A power is to be distributed to the consumers either by a 3-wire DC system or by a 3- phase three wire system .Compare the amount of copper required in the two systems .Assume the same voltage between the outer wire and neutral wire . same percentage loss, balanced load and unity power factor . the middle wires are of half of cross-sectional area as that of outers

A power is to be distributed to the consumers either by a 3-wire DC system or by a 3- phase three wire system .Compare the amount of copper required in the two systems .Assume the same voltage between the outer wire and neutral wire . same percentage loss, balanced load and unity power factor . the middle wires are of half of cross-sectional area as that of outers

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.9P: For the circuit shown in Figure 2.24, compute the voltage across the load terminals.

See similar textbooks

Similar questions

A resistor, in series with a 138-microfarad capacitor, is connected to a 60-cycle source.If the voltage drop across the capacitor is 115 volts and the power taken by the circuitis 922 watts, calculate (a) the circuit current, (b) the ohmic value of the resistor, (c) theline voltage, (d) the circuit power factor. draw the circuit diagram
Discuss the differences between the current coil and voltage coil of a wattmeter from a design point of view.What will be the consequences if the current coil and voltage coil of a wattmeter are interchanged by mistake?What are the possible errors in this measurement?Can you measure power in an ac circuit by using an ammeter and voltmeter? If No, why? If yes, how?What is to be done if the wattmeter reads in the negative direction?
Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v
q1: Discussion of power quality aspects that need to be considered before installing the power factor correction unit
1. A resistor, in series with a 138-microfarad capacitor, is connected to a 60-cycle source. If the voltage drop across the capacitor is 115 volts and the power taken by the circuit is 922 watts, calculate (a) the circuit current, (b) the ohmic value of the resistor, (c) the line voltage, (d) the circuit power factor. Please show complete solution and the circuit diagram. Please round off answers up to the 3rd decimal place. Thank you!
A) An equalizer is a jumper used to parallel the series field of two compound DC generators when the two generators are being run in parallel to share an electrical load. a) true b) false B) The ohmic value of an equalizer is not important as long as it is made out of copper. a) true b) false C) How is the efficiency usually expressed?a) in watts b) in kilowatt-hours c) in percentage d) none of the above
A power plant has a capacity factor of 40.9% and a plant use factor of 45.2%. How many hours per year was the plant not operating?
(b).Explain with reasons why hydro power generation is sometimes disadvantageous.
1. With an elegant diagram, discuss the three-phase power measurement using the three-watt meter method and write down the flaws in this method.
Investigate the topic of power quality in electrical systems. What are the different types of power quality issues, and how can they be mitigated to ensure a reliable power supply?
Briefly explain 3 benefits of improving power factor
A 100-kVA, 3,000-V, 50-Hz, 3-phase starconnected alternator. The effective resistance to ohmic resistance is 1.5. The ohmic resistance is obtained by connecting two terminals to a dc source. The current and voltage are 15 A and 6 V. A field current of 40 A produces short-circuit current of 200 A and an open-circuit e.m.f. of 1040 V (line value). Calculate the full-load percentage regulation and efficiency at a power factor of 0.8 lagging, with field and stray power losses equal to 2750 W.