A pressure gauge tester is shown in Figure 3.3. The cylinder is filled with oil, B,-475x10-12PA-. The diameter of piston is D=15 mm, the screw pitch t-2mm. At the atmospheric pressure, the volume of oil in the cylinder including pipeline is V=250cm³. For the reading of 25.0MPA in the pressure gauge, how many revolutions do the handwheel must screw in?

A pressure gauge tester is shown in Figure 3.3. The cylinder is filled with oil, B,-475x10-12PA-. The diameter of piston is D=15 mm, the screw pitch t-2mm. At the atmospheric pressure, the volume of oil in the cylinder including pipeline is V=250cm³. For the reading of 25.0MPA in the pressure gauge, how many revolutions do the handwheel must screw in?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

From the setup shown in the figure: If the manometer reads 60 mm, determine the gage pressure at B. If the pressure at B is 3.5 kPa, determine the manometer reading. Hg A Water Air 750 mm 200 mm 80 mm B Oil S=0.8
7) For the manometer setup shown, determine the difference in pressure between A and B. oll, s = 0.85 Water 680 mm Bo 1700 mm YWater 8) A differential manometer is attached to a pipe as shown. Calculate the pressure difference between points A and B. is h. 100 mm re A Mercury A B Oil, s = 0.90 %3!
Hemispherical dome - SG = 0.8 4 m 60 kPa 3 m 3 m Water 2 m B
This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The manometer is open to the atmosphere. There is no flow in the pipe. What will be the gage pressure reading at A? correction: 3.75 mm should be 375 mm en Me Do not write the unit. You will only input the numerikal answer in the space provided. Unit of the Correct Answer. kPa Decimal Places required in the firal answer 3
• A simple U tube manometer is given below. The pressure at which side is higher? o Left o Right o Left = right • In order to calculate the pressure difference at locations 1 and 2 (P2 - P1), we need to know the length of the inclined tube L, as is shown below. o True o False A fow section fow device Fluid
1. A differential manometer is attached to a pipe as shown. Calculate the pressure difference between points A and B. ₪t Mercury o..A 2. A manometer is attached ched and the mercury. to a water tank shown in the figure (a.) find the height of the free water surface above the bottom of the tank; (b.) Find the pressure at the interface of the water to a O water ROPERTON 100mm 0.15m 0.15m Oi, s 0.9 0.2m Hg(13.6)
c) The orifice flowmeter shown in Figure 4 is used to obtain the flowrate of oil inside a conduit. The diameter of the orice, d is one third of the pipe diameter, D with pressure difference recorded as 25 kPa. The pipe diameter D is 6 cm, discharge coefficient Ca, is 0.60, Bis the ratio of orifice diameter to pipe diameter and Oilspedific gravity, SG is 0.95. If the h is 7 cm, i. Calculațe the vollime flowrate of oil inside the conduit. ii. Determine the mass flowrate of oil inside the conduit. iii. Explain why the discharge coefficient Ca, for the orifice meter is higher compared to the venturi and nozzle meters. D=6 cm d Figure 4
A differential manometer is attached to a pipe, as shown in the figure. Calculate the pressure difference between points A and B (P,- P, ). Mercury (s.g. = 13.6) 0.6 ft y Oil B (s.g. = 0.91) %3D
Part 2Two pipes are connected by a manometer as shown. Determine the pressure difference, between the pipes in kPa.
1. A block, 1ft square and 9 inches deep floats on a stratified liquid composed of a 6in layer of water above a layer of mercury. Determine the weight of the block if the position of its bottom is 1 inch below the mercury. 2. At point A in a pipeline carrying water, the diameter is 1m, the pressure is 98kPa and the velocity is 1m/s. At point B, 2m lower than A, the diameter is 0.5m and the pressure is 20kPa. Determine the direction of flow. Show detailed computation. 3. What is the hydraulic radius of the channel shown: 1.5m 1.5h 4. wty A vertical right-angled triangular surface has a vertex in the free surface of a liquid. Find the force on one side. 1.5m 1:2m
Water flows through a pipe reducer shown in figure 2. The static pressure in the large diameter pipe and the small diameter pipe are measured by the inverted U-tube manometer containing oil of specific gravity less than one. Determine the manometer reading, thus show that h is given by the equation h = ng(1-SG) la SG Water Figure 2 The diameter of a pipe changes gradually from 75 mm at a point A, 6 m above datum, to 150 mm at B, 3 m above datum. The pressure at A is 103 kPa and the velocity of flow is 3.6 m/s. Neglecting losses, with the aid of a neat sketch, determine the pressure at B.
For the manometer shown, determine the pressure at the center of the pipe. J - Mercury , sg= 13.55 Oil, sg= 0.80 1.5m