A pressure gauge which can be modeled as a Linear Time-Invariant (LTI) system has a time response to a unit impulse input h(t) given by (Ge-2ª +e¬")u(t). For a certain unknown input, the output y(t) is observed to be (4e7t – 8e2“)u(t). For this observed measurement, derive the true pressure input x(t) to the gauge as a function of time. Assume that the input signal is right-sided. -4t

A pressure gauge which can be modeled as a Linear Time-Invariant (LTI) system has a time response to a unit impulse input h(t) given by (Ge-2ª +e¬")u(t). For a certain unknown input, the output y(t) is observed to be (4e7t – 8e2“)u(t). For this observed measurement, derive the true pressure input x(t) to the gauge as a function of time. Assume that the input signal is right-sided. -4t

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Discussion: 1- Measuring the angle of phase shift for every state. set the AC voltage source 15V and using the data in the following table NO. Frequency | Capacitance | Resistance | Inductance 1 2KHZ 0.1uF 100Q 0.1mH 2 20 KHZ 0.1 yF 100 Q 0.1 mH 3 200 KHZ |0.1 pF 100 Q 0.1 mH 2- Draw the phase shift for every state as graph .
What will be the ln (natural logarithmic) value of the temperature (t), if a sensor has medium temperature 140 °C, Initial Temperature 25 °C and actual temperature is 60 °C. ln value of temperature, t
The response of a system is given by xt=0.003cos 30t +0.004sin 30t m. Determine (a) the amplitude of motion, (b) the period of motion, (c) the frequency in Hz, (d) the frequency in rad/s, (e) the frequency in rpm, (f) the phase angle, and (g) the response in the form of xt=Asin (ωt+φ)
The mass of a solid hemisphere is measured once with a digital balance whose resolution is 1 g. The result is m = 50 g. With a caliper, the resolution of which is 0.05 mm, repeated measurements of the diameter D of the hemisphere are carried out. The values obtained for D: 100.30 mm; 100.00 mm; 100.60 mm; 100.10 mm; 100.25 mm; 100.50 mm; 100.40 mm; 100.20 mm; 100.30 mm; 100.35 mm. The result of measuring the mass m is: (a) (50 ± 1) g (b) (50.0 ± 0.58) g (c) (50.00 ± 0.58) g (d) (50.0 ± 0.5) g
A temperature measurement system is composed of a sensor and a readout device. The readout device has a claimed accuracy of 0.6 °C with a resolution of 0.1 °C. The sensor has an off-the-shelf limit of error of 0.5 °C. Estimate a design-stage uncertainty in the temperature indicated by this combination. A displacement transducer has the following specifications: Linearity error:±0.25% reading Drift:±0.05%/°C reading Sensitivity error: ±0.25% reading Excitation: 10-25 V Output: dc 0-5Vdc Range: 0-5 cm The transducer output is to be indicated on a voltme- ter having a stated accuracy of 0:1% reading with a resolution of 10 μV. The system is to be used at room temperature, which can vary by 10 °C. Estimate an uncertainty in a nominal displacement of 2 cm at the design stage. Assume 95% confidence.
10/. A capacitor of 1 μF is connected to a 50 Hz supply. The capacitive reactance (Xc) is ___________. 1591.54 Ω 3183.09 Ω 3.141 Ω 6.283 Ω
A vibrometer with mass 0.86 kg and damping ratio ζ 0.62 is designed to measure vibration in the frequency range ωb = 34.8-84.7 rad/sec. Chose the appropriate stiffness from the given values to guarantee the maximum error will not exceed 2% Note:ZY=r2(1−r2)2+(2rζ)2√ a. 115 N/m b. 367 N/m c. 85 N/m d. 2173 N/m e. 680 N/m
1- I need answer of all sub-parts questions. Thanks The figure shows a simple model of a motor vehicle that can vibrate in the vertical direction while traveling over a rough road. The road surface varies sinusoidally with an amplitude of 0.01 m and a wavelength of 6 m. The vehicle has a mass of 1007 kg. The suspension system has a total spring constant of 40 kN/m and a damping coefficient of 20 kN.s/m. The vehicle average speed is v = 100 km/hr. The objective is to determine the vehicle steady-state displacement amplitude as well as the respective transmitted force. Calculate the forcing frequency of the pumpy road. Calculate the natural frequency of the vehicle SDOF system. Calculate the damping ratio of the vehicle SDOF.
Vibrations Question The governing equation of motion of a single degree–of–freedom (SDOF) system is given by 5xdoubledot(t)+20xdot(t)+1800x(t)=10cos(15t)+30sin(5t)(assume the units are Newtons) and the initial conditions of the system are given asx(0)=0.02m and v(0)=0.95m/sAnalytically obtain the total response of the system
2- I need answer of all sub-parts questions. Thanks The figure shows a simple model of a motor vehicle that can vibrate in the vertical direction while traveling over a rough road. The road surface varies sinusoidally with an amplitude of 0.01 m and a wavelength of 6 m. The vehicle has a mass of 1007 kg. The suspension system has a total spring constant of 40 kN/m and a damping coefficient of 20 kN.s/m. The vehicle average speed is v = 100 km/hr. The objective is to determine the vehicle steady-state displacement amplitude as well as the respective transmitted force. Calculate the resultant frequency ratio of the above model. Calculate the steady state amplitude of the vehicle. Determine the force amplitude that will be felt in the vehicle at the steady-state due to the bumpiness of the road.
A displacement transducer has the following specifications: Linearity error: ±0.25% reading Drift: ±0.05%/°C reading Sensitivity error: ±0.25% reading Excitation: 10-25 V dc Output: 0-5Vdc Range: 0-5 cm The transducer output is to be indicated on a voltmeter having a stated accuracy of 0:1% reading with a resolution of 10 μV. The system is to be used at room temperature, which can vary by 10 °C. Assume 95% confidence. The displacement transducer above is used in measuring the displacement of a body impacted by a mass. Twenty measurements are made, which yield Determine a best estimate for the mass displacement at 95% probability based on all available information.
A displacement transducer has the following specifications: Linearity error: ±0.25% reading Drift: ±0.05%/°C reading Sensitivity error: ±0.25% reading Excitation: 10-25 V dc Output: 0-5Vdc Range: 0-5 cm The transducer output is to be indicated on a voltmeter having a stated accuracy of 0:1% reading with a resolution of 10 μV. The system is to be used at room temperature, which can vary by 10 °C. Assume 95% confidence. The displacement transducer above is used in measuring the displacement of a body impacted by a mass. Twenty measurements are made, which yield X= 17.20mm Sx= 1.70mm Determine a best estimate for the mass displacement at 95% probability based on all available information.