Homework Questions from Fellow Students

Browse our recently answered homework questions.

Q: 5 - There are 4 pulleys in each block of a set of rope pulley blocks. If the efficiency is 70% when…
Q: i need the right answer please quick i give u good feedback the answer is bellow
Q: The beam is made of steel and has a profile of a hollow triangle with the wall thickness of 4 mm.…
Q: 1-1, Draw the influence lines for: (a) the reaction at B (By), and the (b) shearing force and (c)…
Q: Q2: Find the equivalent mass of the rocker arm assembly shown in the figure with respect to the x…
Q: ۲/۱ : +0 العنوان In the mechanism shown in Figure of, the crank AB, which is 100 mm long rotates a…
Q: what is the haet flux due to radiation across one square meter of fin surface area in a vehicle's…
Q: A composite wall is made of wood (Zw = 0.0127 m), cork-board (Lcb = 0.1016 m), and concrete…
Q: A rod that has a solid circular cross-section with a diameter of 30 mm is subjected to the shown…
Q: A machine part made of cast aluminum has the properties Sut = 40 kpsi, Suc = 35 kpsi and ε = 0.045.…
Q: 4: Find the smallest force P that the worker must apply to the bar CD in order to initiate uphill…
Q: Color the entire pipe systems for the  green for the grease wastepink for the sanitary lineblue for…
Q: please i need her solving and the right final answer of this numbers bellow
Q: Could I get this question broke down and fully explained?  thanks
Q: Question: B08-5 This is a question based on the text book ‘’Mechanics of Materials’’ , please reply…
Q: Q3: Draw the free-body diagram and derive the equation of motion (EOM) using: (1) Newton's 2nd law…
Q: mechanical
Q: Some area, A, is bounded by the functions: y = 1, x = 0 and y = 10 - x2 a) On a sketch of the…
Q: A-7.6: A drive shaft resists torsional shear stress of x = 40 MPa and axial com- pressive stress σx…
Q: Question: B05-3 This is a question based on the text book ‘’Mechanics of Materials’’ , please reply…
Q: A cylindrical pressure vessel of 2 m radius and 0.05 m wall thickness is manufactured from a steel…
Q: very urgent i need the right answer quick please
Q: 7: Determine the range of cylinder weights W for which the system is in equilibrium. The coefficient…
Q: 400 300 LL 1.1 A console consists of two bars, which are flexible supported and connected to each…
Q: %११। A 1.:Po Steam Powerpc Wed He Home IGHT Desion 52 Regences YIW Hed f me what you want to go…
Q: Problem 7 (7 points, CCO #9) / Gradescope Solve the PDE Iw Iw x + sin(y) = 0 მყ მე analytically…
Q: What would be the pressure just downstream of the shock?
Q: Determine the maximum mass of the engine, which can be supported with the system of chains shown in…
Q: 1. A fan that can provide air speeds up to 50 m/s is to be used in a low-speed wind tunnel with…
Q: (previous test for fluids 3, exam prep) The pump whose performance data is plotted in Figure 4 was…
Q: Use graphical imaging to determine the accelerations of the given four-bar / inline slider…
Q: 6-36 4 kN 1.5 m 8 kN ד 2 m 2 m Determine the forces in members AF, BF and BC using method of…
Q: quickk pls
Q: Τρ סוי D2L Notes de cours 2 - MA... D2L Solutions d'examen -... B https://uottawa.brights... ChatGPT…
Q: In this question,, which cup will full first, explain well
Q: QUESTION #4 For the beam show below, determine the reaction RA and the distance (d). 0.2 kN 2.7 kN…
Q: The tripod shown supports a 5-m by 2-m rectangular panel through member AB, which is parallel to…
Q: please very urgent i need the right answer please be carfully
Q: Consider the truss shown in (Figure 1). Suppose that F = 13 KN. Determine the force in member CD and…
Q: 3. A pulley is driven by a flat belt running at a speed of 600 m/min. The coefficient of friction…
Q: 4. Solve the following differential equations: a- y" +zy' ty = x² b- y" -4y = Sinx <- 4"+zy! +y=ex…
Q: En el sistema de engranes planetarios que se muestra, los ra-   dios de los engranes A, B, C y D son…
Q: 17: Determine the force in members CD, CF, and GF using method of sections. State whether each…
Q: ⚫ A thin silicon chip and an 8-mm-thick aluminum substrate are separated by a 0.02-mm-thick epoxy…
Q: Solve with method of sections
Q: If σY = 50 [ksi], determine the factor of safety for this state of stress against yielding, based on…
Q: Determine the gross take-off weight of the aircraft
Q: A circular shaft has a diameter D = 40 mm and a length L = 1.5 m and is made of structural steel…
Q: Q4: A steel cantilever, the factor of safety is 2, the sensitivity factor 0.9, surface finish factor…
Q: The two cross sections shown below, (a) and (b), are subjected to a vertical shear force as shown.…