b Πa M 0 k wwwwww Rigid bar

Q: if A = B = C = D = E = 40N Find the net torque at point p. D 350 A B p. E 1m 450 C 1m if A = B = C =…

A:

Q: A 50 mm X 80 mm rectangular steel plate subjected to the uniaxial stress condition is shown in the…

A:

Q: The mass of CO2 is 0.067 kg in a system (with molar mass 44 kg/kmol), occupying a volume of 0.026 m³…

A:

Q: the omnidrive that was mentioned above should be an agriculture related machine

A: Omni drive is an agriculture-related machine that is used to help the farmers in their fields.…

Q: In a piston cylinder system, fluid at 0.8 bar occupying 0.07 m³ is compressed reversibly to a…

A:

Q: What is the weight of a 0.5 slug traveling at 35 ft/s?

A: Given:m=0.5 slugv=35 ft/s

Q: Q3//Find the plastic tensile strain at failure alloy rod have initial length 1m with a 50cm in…

A: given data initial length = 1 m , diameter = 50cm final length = 3 m find the plastic tensile strain…

Q: 2- An ideal Diesel cycle has a compression ratio of 15 and a cutoff ratio of 1.7. Determine the…

A: Diesel cycle is a type of constant pressure heat addition cycle which consists of 4-processes:-…

Q: Determine the width and thickness of the leaves (in mm) of a leaf spring using the following…

A:

Q: Draw the shear and moment diagrams for the beam shown below. 60KN 30KN.m A B. 1m 2m

A: First calculate the reactions at support s

Q: Q1 A Carnot refrigeration cycle absorbs heat at -8°C and rejects heat at 55°C. (a) If the heat…

A:

Q: 6- A liquid has a specific weight of 59 lb/ft' and a dynamic viscosity of 2.75 lb s/ft. Determine…

A: Given data:- specific weight = 59 lb/ft^3 dynamic viscosity = 2.75 lb-s/ft^2 find the kinematic…

Q: e diameter of the spherical container in mm

A: To find Diameter of spherical container.

Q: A 1 lbm/s fluid enters a machine at 170 m/s, 800 kPa, and with a specific volume of 0.3 m3/kg. The…

A:

Q: A small car of mass 2000-kg reared a stalled truck of mass 3000-kg on a straight road. The two…

A: given data  mass of car = 2000kg mass of truck = 3000 kg initial velocity of car = 30 m/s find the…

Q: As the hydraulic cylinder rotates around 0, the exposed length I of the piston rod P is controlled…

A:

Q: (a) Determine the reactions at A and E if P = 830 N. The reactions are positive if to the right or…

A:

Q: A counter flow double pipe heat exchanger using super heated steam is used to heat water at the rate…

A:

Q: An area-variation-based capacitive accelerometer, as shown in Figure below, has the following…

A:

Q: Pressure drop and heat transfer in suction line Decrease compression ratio & discharge temperature…

A: Correct answer: (B) increases compression ratio & discharge temperature

Q: addition process, 175 cm3 at the end, and 1300 cm3 at the beginning of the heat rejection process.…

A:

Q: What are the factors affecting shearing stresses in beams?

A:

Q: 44. Draw a free-body diagram of member AC in Figure P4-4. -2 m 3 m A T 1 12 50 kN FIGURE P4-4

A: Draw free body diagram of member AC.

Q: A load P is supported by two steel springs arranged in series. The upper spring has 20 turns of ¾ in…

A:

Q: Q3: Ethanol at 20°C flows at 0.008 m³/s through a horizontal cast iron (ε = 0.26 mm) pipe with L =…

A: Answer: (a) The pressure gradient: 4115.5 (N/m2)/m. (b) The wall shear stress: 51.4440 N/m2. (c) The…

Q: 12 mm Determine the following: a. Shearing Stress in the head bolt. b. Shearing in the thread c. The…

A:

Q: (a) Using sketches, describe the carburisation process for steel components. (b) The yield stress…

A:

Q: For the system shown in Figure 1, the natural frequency of the system is 170 Hz. The rod has length…

A:

Q: capacity (in gpm) of a 4-1/2 inch impeller centrifugal pump operating at a speed of 345O rpm capable…

A: we have to calculate flow

Q: • Part A The 23 ky slander red is allachod to a spring, which hs an unatretchec length ot 2 m.…

A: Given Datam=23kgl=2mθ=30°

Q: Figure 1: P = 400 kN 30° 1000 mm Area 30 mm 20 mm In Figure 1, if the Young modulus is 200 Gpa, the…

A: Given data:- force P = 400kN find the strain percentage in the direction of the normal force.

Q: If your roll number is 12L3456, 12 represents your batch and 3 is the first digit of your roll…

A:

Q: A control mass system undergoes a three-process power cycle with air as the working fluid. Air at…

A: INTRODUCTION: In this problem, three procedures are sequentially followed by one another. The first…

Q: Pressure drop and heat transfer in suction line Decrease compression ratio & discharge temperature…

A: Answer - Option -B [ Increase compression ratio and discharge temperature ]

Q: In a piston cylinder system, a fluid at 0.6 bar occupying 0.07 m³ is compressed reversibly to a…

A:

Q: The air compressor in the core of the CFM56-5A1 turbofan engine of the Airbus A320 compressors 50…

A: INTRODUCTION: The isentropic process is a constant entropy process, which indicates that anytime a…

Q: Q2. The system shown below is in equilibrium. Find the reactions at A (hinge support) and the force…

A: find the reaction at point A and force at B.

Q: In fluid rotated solid about a vertical axis with angular. a a Velocity (w). The pressure vise (P)…

A: The pressure rise obtained by considering a differential element.

Q: A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal…

A: given data :-  force P= 400kN find the normal force component at point A.

Q: 11- Consider a steam power plant that operates on the ideal regenerative Rankine cycle with a closed…

A:

Q: Technician A says that the PCM illuminates the mil if a defective causes emission levels to exceed…

A: If the emission level exceeds the threshold limit then PCM illuminates the mil. But it is not only…

Q: At a given section a shaft is subjected to a bending stress of 30 MN/m2 and a shear stress of 60…

A:

Q: At t=0, temperature of water suddenly changed from 25°C to 100°C. The transfer function of the…

A: The table for the time and voltage is Time(Sec) Voltage 0.0 0.3 0.1 1.8 0.2 2.8 0.3 3.4…

Q: Consider a conical water tank with a base and height of 8m and 10m, respectively. How much work will…

A:

Q: Q4: The mechanism shown in Figure is in equilibrium for an applied load of P-20 KN. Specifications…

A:

Q: Consider the coupled oscillators shown below with k= 8 N/m, k = 5 N/m and m = 2 kg. Given the…

A: Given : To find :

Q: 1. A bar is subjected to a tensile stress of 100 MPa, Determine the normal and tangential stresses…

A: Givenσ=100Mpaθ=30o

Q: steam power plant of 40% thermal efficiency receives heat of 150 MJ at high temperature while…

A: Given data :- thermal efficiency = 40 % heat received = 150 MJ work for circulating water = 10 MJ…

Q: Ductile cast iron is also known as iron. O cluster O flakes cementite O nodular

A: Ductile iron is also known as, spheroidal or nodular iron.

Q: The reversible first-order gas reaction 1 A2R s to be carried out in a mixed flow reactor. For…

A:

Free Damped Vibrations

Free vibration is a type of vibration in which the external force is removed after giving the initial displacement to a body/system. In other words, in this type of vibration, force is applied at the initial displacement of the system, and after the initial displacement, force is removed, and the system vibrates at the natural frequency.