A propeller shaft in a ship is 400 mm in diameter and 6 m in length. The allowable shearing stress is 60 MPa and the allowable angle of twist is 2°.If G= 65GPa, determine the maximum torque the shaft can transmit.

A propeller shaft in a ship is 400 mm in diameter and 6 m in length. The allowable shearing stress is 60 MPa and the allowable angle of twist is 2°.If G= 65GPa, determine the maximum torque the shaft can transmit.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Related questions

Q: A pipe AB carries water and tapers uniformly from a diameter of 4" at A to 8" at B over a length of…

Q: A local municipality is tasked with managing the sediment from its three streams originating from…

Q: 10. Give the balanced chemical equation for the complete combustion of gaseous methane (CH4).

Q: A composite cantilevered rectangular beam with a length of 1 meter. Height = 65 mm, width = 25 mm.…

Q: square aluminum bar is to support a load of 40 kN on a length of 3 m. ssuming pinned ends, determine…

Q: Compute the normal acceleration when the boy reaches the bottom of the profile. (m/s^2)

Q: two 5 cm diameter, 15 cm long aluminum bars (k=176W/m(degrees Celsius)) with ground surfaces are…

Q: Situation #1: The initial angular velocity of the compound pulley B is 6 rad/s counterclockwise and…

Q: An object is shot upward from the ground with an initial velocity of 640 ft/sec, and experiencés a…

Q: problem: In the tollowing Figures, Find the force torque at the given paints. 200 N Loo N 200 N EMA…

Q: A Carnot engine operating between 527C and 27 C produces 600KW of work. Determine, (a) Qa, KW; (b)…

A: GivenT1=527oC=800KT2=27oC=300KW=600kW

Q: Q=2000J Tout=? V(m/s) D=0.1m air Air at (3.200x10^2) K is entering in a circular pipe at 101325 Pa…

Q: A spring subjected to torsional stress is made of hard-drawn brass wire. The ultimate strength in…

A: Spring are used to absorb energy or restored it slowly or rapidly according to the function of a…

Q: A tensile specimen has an elastic modulus of 50 GPa. If the length of the specimen before being…

A: Answer: ◆ The final length of the specimen is 282 mm. ◆ Therefore, the correct answer is option (d).

Q: Consider all 4 steps and derive and expression for the efficiency of a Carnot cycle that uses a van…

Q: Let's assume the rocket has a rest length of 57 m and the hangar has a rest length of 51 m.…

Q: Isentropic Work of the Steam using the Ideal Rankine Cycle when the system is set at 400 kPaa Boiler…

Q: Suppose the vector field v = (x, y,−z) is the velocity vector for a steady (time independent) fluid…

A: Equation of streamline is given by, dX/u=dy/v=dz/w dX/x=dy/y=dz/-z Integrating 1st and 2nd we get,…

Q: Question 1 A large block of mass 1100 kg is towed at a constant speed UB up an inclined plane at 6°…

Q: Internal pressure and axial tensile force are applied to an open cylindrical tank 605 mm in diameter…

Q: Q,B = 1 ½ inches, BC = 4 inches, Q¿C = 3 inches, Q‚E = 2 inches, EF = 5 %3D hes and Q,Q4 = 5 inches.…

Q: The complex mechanical impedance in a pipe at (x = 0) is Z =-jp.cS Cot(kL) if the other end (x L) of…

A: Answer: Each of the impacts considered in this study is symbolized by a different F-value, for a…

Q: The unit cell has a = 5 A, b=S A, c= 3 A, a = 90, B 65 and y 54. The space lattice for this unit…

Q: Develop the shear and bending moment diagrams for the beam 6 kN/m 2.4 kNm B 4 m .6m.

Q: what is the final answers?

A: There are two subparts to this problem compute the total head loss from A to D if the flow is 1700…

Q: Determine the change in length of the 20 mm diameter rod AD, subjected to the indicated forces (E =…

A: To find Change in length.

Q: Determine the magnitudes of the forces C and T, which, along with the other three forces shown, act…

Q: A Determine: al The support and joint reactions. b/ The stress resultants in beam BD. F 3L MaFL-

Q: A 2-inch line shaft is transmitting 20 hp rotating at 200 rpm, carrying two pulleys spaced 30 inches…

Q: A steel rod is 2.2 m long and must not stretch more than 1.2 mm when a 8.5 kN load is applied to it.…

Q: Calculate the theoretical amount of air fuel ratio required for the combustion of ethane, C2H6

Q: A square steel alloy plate 400 mm on a side has a 90-mm-diameter circular hole at its center. The…

Q: The given figure shows a thermal network with T1 = 325.15 K, T1 = 310.15 K, Rwall = 0.08 K/W, and…

Q: Problems: 2-1 For the figure shown, below, V = 2.5 n/s in the direction shown 1) Make scaled drawing…

Q: A block sits on a plane, and there is friction between the block and the plane. The plane is…

A: Graphical representation of forces may be applied externally, reactions ( normal force, tension,…

Q: Determine C/R for the

A: To determine C/R using block diagram Verify the result using signal flow graph. Topic : Control…

Q: The scoop holds a 2,000 N weight concentrated at G. If all links are in duplicate, determine the…

A: W=2000N∑MB=0Fkjx(180+100+160)=2000×200Fkjx=909.09N(−ve)∑FN=0FcB cos14.04°+Fkjx=0FCB=+937.08N…

Q: 1. A museum of modern art is displaying an irregular 426-N sculpture by hanging it from two thin…

A: Given W=426N

Q: Determine the Internal Shear and Moment at point C of the Beam shown. w = 5 kips/ft A В 9'- P = 10…

Q: Two cars moving on the same direction have a velocity of 90 ft/sec. Car A is 100 feet behind car B.…

A: Given data the velocity of cars A and B are 90 ft/sec To determine required acceleration of…

Q: Water at 200∘F enters the radiator at A with an average velocity of 4 ft/s and a pressure of 60 psi.…

A: given data for a radiator Vavg=4ft/spa=60 psi…

Q: For a 34.4 mm diameter smooth pipe, calculate the threshold velocity (m/s) and corresponding flow…

Q: 9. Give the balanced chemical equation for the decomposition of C2H«O.

Q: Moment of Inertia of an Area w.r.t (a) the x-axis (b) the y-axis Determine the second moment of the…

Q: centrifugal pump develops a head of 16.8 m at 1500 rpm. Rated capacity is 0.015 m3/s. Determine the…

Q: A fluid is weighted in a laboratory. It is found that 6 LITERS of the fluid weight 37 N. What is the…

A: Given:Volume of the fluid, V=6 liters or 0.006 m3fluid weight, w=37 N

Q: There are 1.5 kgm of gas for which R=0.377kJ/kg-K and k=1.3 that undergo an isometric process from…

A: Given Mass, m = 1.5 kg Heat removed, Q = - 1500kJ R =…

Q: A stress-strain diagram for a polymer is shown. Identify items A, B, and C. A= lower yield point; B…

A: Given

Q: A steel pipe has an inside diameter of d = 350 mm and an outside diameter of D = 158 mm. The length…

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A propeller shaft in a ship is 325 mm in diameter and 4.875 m in length. The allowable shearing stress is 55 MPa and the allowable angle of twist is 3°. If G= 50 GPa, determine the maximum torque the shaft can transmit.
A propeller shaft in a ship is 350mm in diameter and 5.25 m in length. The allowable shearing stress is 50MPa, and the allowable angle of twist is 1 degree. If G=85GPa, determine the maximum torque the shaft can transmit.
A solid shaft is to transmit 22kW at 110 rpm. Determine the diameter of the shaft if the shearing stress is not exceed 35 MPa and the angle of twist is limited to 5 degrees in a length of 4m. Use G=86 GPa.
A hollow cylindrical shaft has outer diameter of 115 mm and inside diameter of 75 mm. Determine the maximum torque that can be applied if shearing stress is limited to 50 MPa andthe shaft can only sustain a twist of 0.8 degrees per meter. Use G = 83 GPa. Express your answer in N-m.
An aluminum shaft of two segments is shown below. Determine the allowable torque if the shear stress is not to exceed 30MPa and the angle of twist between the ends of the bar is not exceed 2.3°? (Assume G=80GPa)
Calculate the unit shearing stress at the inner surface of a hollow shaft which D = 150 mm and d = 80 mm due to a torque of 30 kN-m. A)26.3 MPa B)33.6 MPa C)20.4 MPa D)18.4 MPa
A solid shaft having a diameter of 100mm has an allowable shearing stress of 80 MPa. Determine the maximum torque in KN-m that the shaft can carry without exceeding the allowable shearing stress.
A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so as not to exceed a shearing stress of 42 MPa and an angle of twist of more than 5 degrees in a length of 3 meters. G = 83 GPa
a solid shaft in a rolling mill transmits 20 kw at 2r/s. determine the diameter of the shaft if the shearing stress is not exceed to 40 Mpa and the angle of twist is limited to 6 in length of 3m. use G=83 gpa.
Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer diameter and 80mm inner diameter. The shear stress is limited to 70 MPa, and the angle of twist must not exceed 0.4 degrees in a length of one meter. Use G = 83 GPa for steel.
A 2-in diameter steel shaft rotates at 240 rpm. If the shearing stress is limited to 12 ksi, determine the maximum horsepower that can be transmitted.
Q3 A hollow shaft with an external diameter of 160 mm transmits a maximum torque of 16 kN.m.If the maximum shear stress is limited to 50 MPa, calculate the inside diameter of the shaft. Also determine the angle of twist in degrees for a shaft length of 7 m as well as the minimum shear stress in the shaft (G=84 GPa).