A pump is used that has a Power Pb= 40HP and works with an efficiency of 85% to drive a flow rate Q of oil through the system shown in the figure. The suction pipe has a diameter D1= 10 inches and the discharge pipe has a diameter D2=8 inches; Between the suction tube and the discharge tube there is a differential pressure gauge with mercury, which shows a column h = 45 in. Find the flow

A pump is used that has a Power Pb= 40HP and works with an efficiency of 85% to drive a flow rate Q of oil through the system shown in the figure. The suction pipe has a diameter D1= 10 inches and the discharge pipe has a diameter D2=8 inches; Between the suction tube and the discharge tube there is a differential pressure gauge with mercury, which shows a column h = 45 in. Find the flow

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe 50 cm in diameter carries water (l0°C} at a rate of 0.5 m 3 / s. A pump in the pipe isused to move the water from an elevation of 30 m to 40 m. The pressure at section 1 is 70kPa gauge, and the pressure at section 2 is 350 kPa gauge. What power in kilowatts and inhorsepower must be supplied to the flow by the pump? Assume h L = 3 m of water and α 1 =α 2 = 1. Find the following Draw the Schematic diagram Drive the energy equation Calculate pump head Power requirement
At one point in a pipeline the water's speed is 3.00m/s and the gauge pressure is 5.00•10^4 Pa. Find the gauge pressure at a second point in the line, 11.0m lower than the first, if the pipe diameter at the second point is twice that at the first. note: density of water is 1000 kg/m^3.
Need asap A horizontal pipe of cross section 1.5 in2 has a constriction of cross section of 2 cm2 . Gasoline flows in the larger pipe with a speed of 500 m/hr. Find the speed in the constriction in ft/min. SHOW COMPLETE SOLUTION and conversion
A horizontal air duct reduces in cross-section area from 0.070 m^2 to 0.020 m^2. Assuming no losses, what pressure change (in Pascal) will occur when 6.67 N/s of air flows? (Use Sp.Wt. = 31.4 N/m^3 for the pressure and temperature of air involved.)
1. For a given pump, the diameter, the gauge pressures at the inlet and outlet are −30 × 103 P a and 200 × 103 P a, respectively. If the flow rate is 0.1 m3/s, and the power required is 25 kW, find the efficiency. The intake and discharge are at the same height. 2. The impeller of a radial-flow turbine has an outer radius of 4 f t, turning at 200 rpm. The volume flow rate is 1000 ft3/s, and it discharges in the axial direction. Neglect all losses. If the tangential component of the velocity at the inlet is 5 f t/s, find: (a) The torque exerted on the impeller. (b) The power developed by the machine.
A 200 mm long pipe slopes down at 1 in 100 and tapers from 0.25m diameter to 0.15 diameter at the lower end. If the pipe carries 100 litres of oil of specific gravity 0.85 find the pressure at the lower end. The upper end gauge reads 50 KPa.
The head-discharge characteristic relationship of a pump is given by:H = 40 - 200*Q^2, where H is the total head generated by the pump in meters and Q is the discharge in m^3/s. The pump lifts water through a pipe 0.3 meter diameter over a distance of 1000 meters against a static lift of 25 meters. Find the operating/ duty point (H and Q) if the friction coefficient of the pipe 'f ' is 0.03.
Water flows steadily through a horizontal 30 degree pipe bend. At the inlet point 1, the diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kPa gauge. At the outlet point 2, the diameter is 0.38 m and the pressure is 145 kPa gauge. Determine the forces F_x and F_y necessary to hold the pipe stationary.
smooth steel pipe of diameter 500 mm and length 850 m carries water at the rate of 0.05 m3/sec. Find the head lost due to friction. Take Kinematic Viscosity of water as 0.018 x 10 m2/sec
A horizontal air duct in cross-sectional area from 0.75 ft 2 to 0.20 ft 2 . Assuming no losses, whatpressure change P A -P B will occur when 1.50lb/s of air flows? Use specific weight 0.200lb/ft 3 for thepressure and temperature conditions involved. Assuming elevation at A and B is at the same level. (PLEASE draw a diagram if you could, that would be so helpful than you so much)
In Figure below, a syringe has a piston moves to the right at speed of 18 mm/s by mean of force 2.25 N with no leakage. Find the lengths of each of the cylinder and the needle, if the diameters of the cylinder=5mm and the needle=0.3 mm respectively? [Take the viscosity is 9.8*10^-4 Pa.s and the density of medication is 800 kg/m^ 3 ]
1. in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is flowing with a speed of 1.50m/s. the pipe narrows to 2.50cm. what is the pressure in the narrower region if water behaves like an ideal fluid of sensity 1000kg/m3 2. tensile stress a. the ratio of elasic modules to strain b. the applied force per crosssectional area c. the ratio of change in length to the orig length d. the strain per unit legth e. the same as force