A pump rated at 700W is used to transfer water from an open tank at ground level, to another open tank 18m above ground at a rate of 3.25 kg/s. Neglecting friction losses, determine the efficiency of the pump. O 81.98% 67.42% 88.29% 58.94% Which among the following is an assumption made by the Bernoulli equation? O the pump must operate at 100% efficiency the flow is comppletely horizontal friction is negligible in the flow ल the pressure on one side must be atmospheric

A pump rated at 700W is used to transfer water from an open tank at ground level, to another open tank 18m above ground at a rate of 3.25 kg/s. Neglecting friction losses, determine the efficiency of the pump. O 81.98% 67.42% 88.29% 58.94% Which among the following is an assumption made by the Bernoulli equation? O the pump must operate at 100% efficiency the flow is comppletely horizontal friction is negligible in the flow ल the pressure on one side must be atmospheric

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . What is the resulting flow rate in the system if three pumps are used in series? (a) 0.56 m^3/s (b) 0.48 m^3/s (c) 0.33 m^3/s (d) 0.36 m^3/s HINT: what is the resulting Flow-rate in the system if three pumps are used in series ? Choose correct option above
PAY ATTENTION TO THE QUESTION : What is the resulting flow rate in the system if three pumps are used in parallel? (a) 0.483 m^3/s (b) 0.364 m^3/s (c) 0.333 m^3/s (d) 0.563 m^3/s 1. The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . IT SAYS : if theee pumps are used in parallel PAY ATTENTION Multiple choice choose correct answer
1) Interpret solar power in the context of environmental impact.2. What is the rigid dichotomy between windmill and diesel-driven pumps?3. For a normal windmill-driven pump at 3 m/s wind speed, the yield at a 10 m Head is typically 0.12 liters/s per m2 of rotor area, value windmills in the context of yield.
A Francis turbine rotates at 1600 rpm and a flow rate of 1 m3/sec enters it. The inlet and outlet diameters are 1.2 m and 0.55 m, respectively, and the corresponding sections between the blades are 0.24 m2 and 0.08 m2. The outlet angle of the water from the distributor is 10º, the outlet angle of the wheel b2 = 40º and the manometric efficiency of the turbine is 78%.Determine:a) The net jumpb) The torque and power on the shaft
A pumped storage power plant with a head of 150 m, with a flow rate of 6 cms for power generation and pumping, and continuous operation for 8 hours each time. Try to find (1) the power output during power generation and the total daily power generation; (2) pumping water Hourly power and total daily power demand; (3) Pumped storage power plant efficiency; (4) Adjust the pool capacity? Assuming that the water loss is 8% of the total drop, the combined efficiency of the turbine and generator is 85%, and the efficiency of the pump is 65%.
A centrifugal pump pumps water at a flow rate of 7 m³/s to a height of 10 m. If the pump works at the best efficiency point, find the pump impeller diameter, pump speed, the best efficiency value of the pump, the head at the best efficiency value, and the specific speed of the pump, given that CQ=0.15 CH=6 CP=0.75.
Three pumps are connected in parallel. According to pump performance curves, the shutoff head of each pump is as follows: Pump 1: 7 m Pump 2: 10 m Pump 3: 15 m If the net head for this pump system is 9 m, which pump(s) should be shut off? (a) Pump 1 (b) Pump 2 (c) Pump 3 (d) Pumps 1 and 2 (e) Pumps 2 and 3
What is the flow rate of water through the system shown for the turbine to produce 20 kW. Neglect friction in your calculations. Q=10.75m3/s, P=204kw/273hp
A pump is 2.2 m above the water level in the sump and has a pressure of –20 cm of mercury at the suction side. The suction pipe is of 20 cm diameter and the delivery pipe is short 25 cm diameter pipe ending in a nozzle of 8 cm diameter. If the nozzle is directed vertically upwards at an elevation of 4.2 m above the water sump level, determine the power input in KW into the flow by the pump. Neglect all losses. a.20.31 b.24.04 c.0.10 d.0.52
A hydroelectric power plant site where the average elevation of the headwater is 565 m, the tailwater elevation is 485 m. The base of the centerline of the turbine nozzle is 10 m above the tailrace and the water flow was determined to be equal to that volume flowing through a rectangular channel 9 m wide and a depth of 1.20 m and an average velocity of 4.6 m/s. If the turbine efficiency is 95%, penstock efficiency is 90%, generator efficiency is 85%. The plant is operated 24 hours a day with a load factor of 0.70 and the utilization factor of 0.75. If the turbine is an impulse turbine, determine; The power output of the turbine. The average annual energy production.
Which quantities are added when two pumps are connected in series and parallel? (a) Series: Pressure change. Parallel: Net head (b) Series: Net head. Parallel: Pressure change (c) Series: Net head. Parallel: Flow rate (d) Series: Flow rate. Parallel: Net head (e) Series: Flow rate. Parallel: Pressure change
A pump at 65% efficiency is used to transport water from a large open reservoir to a point 10m above at a rate of 450 L/min, into a vented tank. Assuming friction is negligible and that the efficiency of the motor is 77%, determine electricity required to keep the process running for 24 hours.