Q2: The tool shown in Fig.2 is used in a gluing operation to press a thin laminate to a thicker substrate. If the wheels at points A and B both have 2 in diameter and have frictionless bearings, and a 20 Ib vertical force to the handle of the tool, determine the forces applied to the top of the laminate and the bottom of the substrate. 20 10 in- Iaminate substrate Fig.2

Q2: The tool shown in Fig.2 is used in a gluing operation to press a thin laminate to a thicker substrate. If the wheels at points A and B both have 2 in diameter and have frictionless bearings, and a 20 Ib vertical force to the handle of the tool, determine the forces applied to the top of the laminate and the bottom of the substrate. 20 10 in- Iaminate substrate Fig.2

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.55P: A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of...

See similar textbooks

Similar questions

The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
Draw the FBD of the entire frame, assuming that friction and the weights of the members are negligible. How many unknowns appear on this FBD?
A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
The uniform ladder of weight W is raised slowly by applying a vertical force P to the rope at A. Show that P is independent of the angle .
In a hydraulic press, the small cylinder has a diamter of 1 in, while the large piston has a diameter of 8 in. If a force of 120 lbs is applied to the small piston, what is the force on the large piston, neglecting friction.
In a hydraulic press, the small cylinder has the diameter of 8 cm while the larger piston has thediameter of 22 cm. If the force of 600 N is applied to the small piston, what is the force on thelarger piston, neglecting friction?
Problem 2.- The small piston of a hydraulic lift (Fig. 3) has a cross-sectional area of 3.00 cm2 and its large piston has a cross-sectional area of 200 cm2 What force of magnitude F1 must be applied downwards to the small piston in order to lift a load whose weight is Fg = 15.0 KN?
Weights of 2, 4, 6 and 8 N are fastened to the corners of a 2 m x 2 m frame. If it weighs 10 N, where would the fulcrum (the support point) be placed to balance the frame and the weights?
One end of a post weighing 400 Nand with height h rests on a roughhorizontal surface with ms = 0.30.The upper end is held by a ropefastened to the surface and makingan angle of 36.9° with the post. A horizontal force F isexerted on the post as shown. (a) Ifthe force F S is applied at the midpointof the post, what is the largest value it can have without causing the postto slip? (b) How large can the force be without causing the post to slip ifits point of application is 6/10 of the way from the ground to the top of thepost? (c) Show that if the point of application of the force is too high,the post cannot be made to slip, no matter how great the force. Find thecritical height for the point of application.
In the above system with frictionless pulleys, 45 lb and W weights are hung on both sides. What must the weight W be in order for the 300 lb block to overcome the μ friction force and move on?
A mechanism is used to apply a constant load Q to the seat in the manner illustrated. 1. Determine the following for the angle: - the lengths of LBE and LAB, in m - in degrees, the angles ? and ? 2. Compile the FBDs of members AB, FG, EBH, and GHI in their entirety. 3. Determine the forces involved in the following situations, in Newtons: - FG-member - H-pin - AB-cylinder hydraulic