A pure compound called “TULIP” is used as a primary standard to measure concentrations of IRIS. The volume of the acid that reacts with a known mass of tris tells us the concentration of the IRIS. Find the true mass of TULIP (density = 1.45 g/mL) if the apparent mass weighed in air is 100.00 g. The density of the calibration weights used is 8.00 g/mL.

A pure compound called “TULIP” is used as a primary standard to measure concentrations of IRIS. The volume of the acid that reacts with a known mass of tris tells us the concentration of the IRIS. Find the true mass of TULIP (density = 1.45 g/mL) if the apparent mass weighed in air is 100.00 g. The density of the calibration weights used is 8.00 g/mL.

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter3: Statistical Tests With Excel

Section: Chapter Questions

Problem 9P

See similar textbooks

Similar questions

What are the differences between systematic and random errors and how do they effect accuracy and precision? In what circumstances would you use standard addition (versus a normal calibration curve) to determine the amount of an analyte in a sample? A urine sample, containing analyte Z is analysed by the standard addition method where 5 mL of the original sample was mixed with increasing amounts of a Z standard and each solution diluted to a volume of 50 mL prior to analysis. A plot of the final concentration of the standard in each of the 50 mL samples (x axis) versus The measured signal from the analysis of each 50 mL sample (on y axis) produced a straight line with the general equation: y = 44.72x + 4.06 what was the final concentration of Z in the 50 mL standard addition sample? what was the initial concentration of Z in the original urine sample?
You are provided with a stock standard with a concentration of 100 mg/L, and a solution of unknown concentration. Prepare calibration standards using a 10 mL volumetric flask and a 1 mL piston pipette, and measure on the UV/Vis spectrophotometer (400 nm). Determine the concentration of the unknown after a 1:40 dilution, and provide the concentration of the initial solution. i need to learn how to do the calculations and draw a calibration curve to find concentration of unknown sample after i find the absorbances.
The labware we used in Quant Lab is divided into “qualitative” or “quantitative” analytical purpose. One of the important laboratory skills we learned is to know what specific apparatus is appropriate for the task at hand. For the following procedures, which SPECIFIC glassware, or balance ( CORRECT NAMES, be specific ) should be used? Weigh 1.5 g of hydroxylamine to be ready for the spectrophotometric determination of iron. ______________________ Weigh three crucibles in gravimetric analysis. __________________ Measure out 2 mL of concentrated H2SO4 solution to dissolve the copper oxide ore sample.. _________________
To quantify the amount of ethanol in a beverage, a technician prepared the first solution which contained 4.90 grams unknown, 1.00 grams acetonitrile, and 4.10 grams water. After the GC analysis which reported the peak areas of 5,742 for ethanol and 3,829 for acetonitrile, the technician added 0.20 grams ethanol to the first solution and ran the GC analysis again. This time, the peak areas of 6,382 for ethanol and 3,709 for acetonitrile for solution 2 were obtained. What was the percent by mass ethanol in the original beverage?
A 0.1 g amine-containing compound is dissolved in water then diluted to 100 mL. You subject it to spectroscopic analysis, in order to get the concentration of amine in this compound. Next, you get 1 mL of the previously diluted sample then dilute it again to 250 mL for measurement. Then, you fill 3/4 of a 1-cm cuvette with this diluted sample, and you run an analysis using an AAS. The recorded absorbance is 0.545 at 410 nm. What is the molecular weight of the compound? (The molar absorptivity is 1.23 x 104 cm-1 mol-1 L.)
CHOICES: Increase, Decrease, No Effect and WHY 1. The actual concentration of the sodium hydroxide used in the calibration part of the experiment was lower than the stated value. However, the NaOH solution used in the determination of ΔHrxn was of the correct concentration. [magnitude of ΔHrxn] 2. The test tube used in the determination of the ΔHrxn for nitric acid was still wet with water. [ magnitude of ΔHrxn] 3. The actual concentration of the sodium hydroxide used in the calibration part of the experiment was lower than the stated value. [Ccal] 4. A wet pipette was used to transfer 10.00 mL of 1M HNO3 in the determination of ΔHrxn. [magnitude of ΔHrxn] 5. The thermometer and stopper were inserted to the test tube 5 minutes after adding the base in the calibration part. [Ccal]
How many grams of NaAsO, should be weighed out to prepare a stock solution of 100 mg/L in 500 mL deionized water. Use the stock solution to prepare 4 different standard solution that can be used to prepare an analytical calibration curve to measure the concentration of 750 sample in the concentration range of 10-35 mg/L. Draw a proposed calibration curve (based on the results you achieved).
25 ml of pickled brine was taken from an apple pickled with vinegar and diluted to 500 ml, 25 ml of this was taken and acidity was determined with 0.2 N (Factor: 1.05) NaOH. In the main trials, 6.3 ml - 6.5 ml - 6.9 ml, respectively, 0.1 ml base was used in the analysis without using the sample.For example, how many ppm is its acidity?
Why would you use the method of standard addition to calibrate a measurement instead of a calibration curve?
Ben ran through the experiment and found the best-fit line listed below for his standard calibration curve of absorbance vs concentration in M. y = 3214.0x + 0.0076 Ben then prepared a solution that had 5.00 mL 0.002 M iron(III) nitrate in 1 M nitric acid, 3.00 mL 0.002 M potassium thiocyanate, and 2.00 mL DI water. If the absorbance for the solution was 0.436, calculate the equilibrium concentration of iron(III) thiocyanate in the solution. Report your answer in mM with three places after the decimal.
3c. A solution containing 2.50 mM X (analyte) and 1.20 mM S (standard) gave peak areas of 2509 and 7132 respectively, in a chromatographic analysis. Then, 1.00 mL of 6.00 mM S was added to 5.00 mL of unknown X and the mixture was diluted to 10.0 mL. This solution gave peak areas of 4016 and 3138 for X and S, respectively. Calculate i. the response factor for the analyte ii. the concentration of S (mM) in the 10.0 mL of mixed solutioniii. the concentration of X (mM) in the 10.0 mL of mixed solutioniv. the concentration of X in the original unknown solution
Which of the following are necessary steps in performing paper chromatography? I. Saturate the chamber with the vapor of the mobile phase II. Allow the chromatogram to touch the sides of the beaker III. Place the spots at the same height as the solvents IV. Spot the samples 2 cm apart from each other a. I and IIIb. I and IVc. I, III and IVd. II, III and IV