A radial feeder used in rural distribution shown in fig.below is connected to a concentrated and static load at the receiving end. The feeder impedance is 0.11 + j0.11p.u.The sending end voltage is 1.0 p.u,the constant power load at the receiving end is 1.0 p.u with a lagging power factor of 0.85.Determine the value of k, Vr and ô Z -R+ jX

A radial feeder used in rural distribution shown in fig.below is connected to a concentrated and static load at the receiving end. The feeder impedance is 0.11 + j0.11p.u.The sending end voltage is 1.0 p.u,the constant power load at the receiving end is 1.0 p.u with a lagging power factor of 0.85.Determine the value of k, Vr and ô Z -R+ jX

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit below, a generator is connected to a load via a transmission line. Given that Rs = 10 Ω, Zline= (4 + j2) Ω, and Zload = (40 + j30) Ω: (a) Determine the power factor of the load, the power factor of the transmission line, and the power factor of the voltage source. (hint: pf can be calculated using the equation below, and θv, θi, θz are the phase angles of the voltage, current and the load impedance, respectively) (b) Specify the capacitance of a shunt capacitor C that would raise the power factor of the source to unity when connected between terminals (a, b). The source frequency is 60 Hz. (hint: increasing the source pf to unity requires that Zab = Zc || (Zline + Zload) be purely real.)
Assume that the two balanced loads in Fig. are supplied by an 840-V rms 60-Hz line. Load I is Y-connected with 30+ j40 S2 per phase, while load 2 is a balanced three-phase motor drawing 48 kW at a power factor of 0.8 lagging. Assuming the abc sequence, calculate: (a) the complex power absorbed by the combined load, (b) the kVAR rating of each of the three capacitors A-connected in parallel with the load to raise the power factor to unity, and (c) the current drawn from the supply at unity power factor condition.
A 50 Hz, 250 V single phase power line has the following loads placed across it in paralell; 4 kW at a pf of 0. 8 lagging; 6 kVA at a pf of 0.6 lagging; 5 kVA which includes 1.2 kVAR leading. Determine the overall pf of the system and the capacitance of the capacitor which, if connected across the mains restore the power factor to unity.
For the power system in the fig. below the magnitudes of the sending and receiving end voltages are 1pu. The related loads are: S1 = 6 + j10 and S2 = 14 + j8 The generation to the busbars are rated: 10 + j15 at bus 1 and 10 + j3 at bus 2. The impedance of the line is j0.05pu. The active power at each end of the busbar is 10 pu. Calculate the following: Load angle, Sending end voltage ,Reactive power at the sending end , Reactive power at the receiving end ,Total reactive power in the transmission line , Load at bus 1 , Power factor at bus 1 ,Load at bus 2 , and Power factor at bus 2.
Two balanced loads are connected to a 240-kV rms 50-Hz line. Load 1 draws 30 kW at a power factor of 0.6 lagging, while load 2 draws 45 kVAr at a power factor of 0.8 lagging. Assuming the RYB sequence, determine: (a) the complex, real, and reactive powers absorbed by the combined load, (b) the line currents, and (c) the kVAr rating of the three capacitors ∆-connected in parallel with the load that will raise the power factor to 0.9 lagging and the capacitance of each capacitor. Verify the results by creating a MATLAB Simulink model and program. Obtain the plots for the currents and voltages
Problem : The industrial load requires 40 kW with a power factor of 0.84 leading. The load voltage is 220 Vrms at 60 Hz, and the transmission line impedance is 0.1 + j0.25Ω. Calculate the active and reactive power losses on the transmission line and determine the required active and reactive power at the input end of the transmission line. The answer given : Pline=4.685 kW, Qline=11.713 kvar, PS=44.685 kW, QS=37.55 kvar and I want to know the concept of 'Complex Power'.
A single phase distributor 1 km long supplies a load of 100A at 0.8 p.f. lagging at its far end and a load of 200A at unity p.f. at its mid-point. Both power factors are referred to the voltage at the far end. The resistance and reactance per km (go and return) are 0.1 Ω and 0.2Ω respectively. If the voltage at the far end is maintained at 200V, calculate feeder current, voltage at the sending end . Also find phase angle between voltages at mid-point and sending end.
Exercise 1: A three-phase 3Φ transmission line has an impedance of 0.62+j35.06Ω/phase and supplies a three-phase load of 100MW with a power factor (fp) of 0.8 lagging at 200kV. Taking 100MVA and 215kV as a base, we ask: d-) Calculate the complex power consumed by the load in p.u;e-) Calculate the voltage at the emitter terminal in p.u;f-) Calculate the LT impedance taking 200MVA and 150kV as a new base. PLEASE, TYPE, HAND WRITING GETS UNDERSTANDING.
A balanced three-phase 60Hz abc systems feeds two delta connected loads in parallel. Load 1 draws 40 kVA (Apparent Power) at a lag pf of 0.8, while load 2 absorbs 24 kW (average power) at a lag pf of 0.9. The line-to-line voltage at the loads, between phase A and B, is VAB = 440 angle 30 V rms. Find: a) The phase current IAB1 for load 1. b) The power factor of the combined loads. Thank you for your assistance.
A 50 Hz, 250 V single phase power line has the following loads placed across it in parallel; 4 kW ata pf of 0. 8 lagging; 6 kVA at a pf of 0.6 lagging; 5 kVA which includes 1.2 kVAR leading. Determinethe overall pf of the system and the capacitance of the capacitor which, if connected across themains restore the power factor to unity.
Three loads are connected in parallel to a 1400 Vrms, 60 Hz single-phase source.Load 1: Inductive load S=125 kVA, GF=0.28Load 2: Capacitive load P=10 kW, Q=40 kVARLoad 3: Resistive load p=15 kw a)Find the total P(kw), Q(kVAr), S(kVA) and the power factor of the source.b)When a capacitor is connected parallel to the loads to make the power factor lagging behind 0.8, find the Q(kVAr) and capacitance (uF) of this capacitor.
An investor own two large stores at Dubai. Both malls are connected in parallel and operating at an unknown voltage. The local utility system voltage is 13.8 kVrms and supplied power to the malls through a feeder line with impedance equal to 1+j2.5 ohms. Store 1 is consuming 400 kW at 0.8 pf lagging while Store 2 is consuming 300 kVAR at 0.75 pf lagging. Determine the following: a) The stores' operating rms voltages. b) The total real and reactive power of the ehole system. c) The overall pf of the whole system.