To be transmitted is V, = 12 cos (59t + 10), the impedance of the generation system is neglected, the impedance of the transmission line ZLiena = 20 + j8, the transmission line is connected to an arrangement It is necessary to transmit the electrical power coming from a generation system, the voltage a of two loads configured in parallel of magnitude Z1- = 2+ j6 and Z2-load = 12 + j10. a) Analyze the losses of the system (load and transmission line) without the use of transformers b) By applying the power transmission transformers, analyze the losses of the system (load and transmission line). c) Analyze the efficiency of the system if the power factor is 0.7, considering the output power 45 KW!

To be transmitted is V, = 12 cos (59t + 10), the impedance of the generation system is neglected, the impedance of the transmission line ZLiena = 20 + j8, the transmission line is connected to an arrangement It is necessary to transmit the electrical power coming from a generation system, the voltage a of two loads configured in parallel of magnitude Z1- = 2+ j6 and Z2-load = 12 + j10. a) Analyze the losses of the system (load and transmission line) without the use of transformers b) By applying the power transmission transformers, analyze the losses of the system (load and transmission line). c) Analyze the efficiency of the system if the power factor is 0.7, considering the output power 45 KW!

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5. A single phase overhead transmission line has a supply voltage of 34 kV and a sending end current of magnitude 40 A at 0-8 p.f. lagging is feeding a certain load. The total resistance and inductance of the line are 5 and 21 mH respectively. Draw the practical circuit used and the devices necessary to perform this experiment. Then calculate the sending end power, receiving end current, voltage, power factor, receiving end power and line efficiency Vs 34000 Is 40 Cosos 0.8 R 5 Ps Ir Vr Cosor Pr n 21e-3
4 Sinusoidal voltage source of us(t) = [100 cos ωt]V , (ω = 20Mrad s ) voltage is connected to the input of a transmission line of h = 10m length. The wawe parameters of the line and the impedance of the loading two-pole connected to the output at ω angular frequency are: Z0 = (49, 5 - j2)Ω, γ = (0, 5 + j40)km-1, and Z2 = Z0. Find the voltage amplitude at the nearest point to the source where the voltage phase angle is 0! a) U = 100V b) U = 92, 4V c) U = 36, 8V d) U = 50V
If the normalized admittance visible at a distance d from the load impedance is 1 - j5, how many mho should the input admittance of the parallel side line that must be connected to the 50 ohm transmission line at position d be? (mho = 1/ohm)
Exercise 1: A three-phase 3Φ transmission line has an impedance of 0.62+j35.06Ω/phase and supplies a three-phase load of 100MW with a power factor (fp) of 0.8 lagging at 200kV. Taking 100MVA and 215kV as a base, we ask: d-) Calculate the complex power consumed by the load in p.u;e-) Calculate the voltage at the emitter terminal in p.u;f-) Calculate the LT impedance taking 200MVA and 150kV as a new base. PLEASE, TYPE, HAND WRITING GETS UNDERSTANDING.
S.4) the length of a three-phase power transmission line with a Nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/km. From the end of the line, a 56 MW star connected load is fed with a power coefficient of 0.8 back under a 64 kV interphase voltage. If the line head voltage of the transmission line is 69 kV, calculate the capacity and power of the star-connected capacitor to be shunted into the load connected to the end of the line.
A HV transmission line having receiving end load is 300MVA, 50 Hz line from poin A to point B. Resistance 0.13 ohm/KM , for 160 KM Inductance XL= 0.4 ohm per kilometer Parallel admittance j318 × 10-6 Power Factor 0.8770, 0.8477 lagging, unity and 0.8770, 0.8477 leading Assume desired voltage at the receiving end of the transmission line is not less than 380kV., if the line is supplying rated voltage and apparent power at various power factors given Estimate : a. Sending end voltages b. Voltage regulation c. Efficiency of the transmission line d. Give a technical explanations on the results obtained
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / phase. A load with a power factor of cos2 = 0.8 forward is fed from the end of the line. Since the line voltage at the beginning and end of the line of the energy transmission line is wanted to be kept constant at 115 kV, a) Active and reactive powers drawn from the beginning and end of the line, b) Calculating the power consumed along the energy transmission line and the efficiency of the line. S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34, C = j0.0018316 S. At the beginning of the line, it is desired to write 1920 MW active power and 600 MVAr reactive power lines under 7650kV line voltage. According to this business, a) Calculate the line end magnitudes (U2, I2 and P2). b) What value does the end voltage take when the load fed from the end of the line is deactivated? S.3) The length of a phased energy transmission line with a…
A single phase distributor 1 km long supplies a load of 100A at 0.8 p.f. lagging at its far end and a load of 200A at unity p.f. at its mid-point. Both power factors are referred to the voltage at the far end. The resistance and reactance per km (go and return) are 0.1 Ω and 0.2Ω respectively. If the voltage at the far end is maintained at 200V, calculate feeder current, voltage at the sending end . Also find phase angle between voltages at mid-point and sending end.
In the circuit below, find the value of the load impedance ZL, which must be connected to the output of the circuit for MAXIMUM POWER TRANSFER. If this load impedance you found is connected, what is the amplitude, phase angle and angular frequency values of the circuit that will pass through the circuit? AB=34, BA=43
For the power system in the fig. below the magnitudes of the sending and receiving end voltages are 1pu. The related loads are: S1 = 6 + j10 and S2 = 14 + j8 The generation to the busbars are rated: 10 + j15 at bus 1 and 10 + j3 at bus 2. The impedance of the line is j0.05pu. The active power at each end of the busbar is 10 pu. Calculate the following: Load angle, Sending end voltage ,Reactive power at the sending end , Reactive power at the receiving end ,Total reactive power in the transmission line , Load at bus 1 , Power factor at bus 1 ,Load at bus 2 , and Power factor at bus 2.
The two loads in the circuit shown can be described as follows: Load 1 absorbs 8 kW at a leading power factor of 0.8. Load 2 absorbs 20kVA at a lagging power factor of 0.6. 1. Determine the power factor of the two loads in parallel.2. Determine the apparent power required to supply the loads, themagnitude of the current, Is, and the average power loss in thetransmission line.3. Given that the frequency of the source is 60 Hz, compute the value ofthe capacitor that would correct the power factor to 1 if placed inparallel with the two loads. Recalculate the values in (b) for the loadwith the corrected power factor.