A rection turbine has guide vane angle 30° the runner blades make an angle of 80° relative to the tanget at inlet .the blades width at inlet is 1/4 of the outer diameter .the water does not have any tanget velocity at outlet.the head is 25 m and the rotational speed of the runner is 16.67 rotation per second (rps) the turbine efficiency is 88% determine the runner diameter at the inlet and the power developed by this turbine

A rection turbine has guide vane angle 30° the runner blades make an angle of 80° relative to the tanget at inlet .the blades width at inlet is 1/4 of the outer diameter .the water does not have any tanget velocity at outlet.the head is 25 m and the rotational speed of the runner is 16.67 rotation per second (rps) the turbine efficiency is 88% determine the runner diameter at the inlet and the power developed by this turbine

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Similar questions

A Kaplan turbine working under a head of 43 m deve-lops 15,400 B.H.P. The dia of theboss is 0"3 times the dia ofrunner. Determine the speed and dia of runner, if speed ratio is2, flow ratio as 0-65 and overall efficiency as 91%.
The general energy balance equation for a turbine is: Qnet + Wnet = ΔmH + ΔKE + ΔPE What does it mean when the term ΔmH is negative? Describe what changes occured to the fluid's energy, and where it went.
A centrifugal pump delivers 25 liters of water per second against a head of 10 meters and running at 1300 rpm requires 10 kW of power. Determine the discharge, head of the pump and power required if the pump runs at 1500 rpm. (Ans. 0.0288cumec or 1.73 cu.m./min , 13.31m, 15.36kw)
A Pelton wheel is to be designed for a head of 400 m when running at 500 rpm. The Pelton wheel develops 10000kW shaft power. The blade angle at outlet is 15º. The relative velocity of water is reduced by 5% by moving over the buckets. Velocity of the buckets = 0.45 times the velocity of the jet, overall efficiency = 0.8 and coefficient of the velocity = 0.98. If the Pelton wheel is provided with three nozzle, find (i) The diameter of jet (ii) Total flow rate and the force exerted by a jet on the buckets
The mean radius of an axial flow reaction turbine is 2.6 ft. and the axial velocityis 25 ft./s. The wicket gates are turned at an angle such that relative velocity at theinlet flow makes an angle of -45° with the blade velocity. The wheel and hub radiiare 3.6 ft. and 1.6 ft., respectively. The turbine rotates at 240 rpm. If water leaves theblade in a purely axial direction, calculate H and all relevant angles.Ans: H=81.87 ft.; α1=31.8°; β2=20.93°
Consider an inward flow reaction turbine in which velocity of flow at inlet is 3.8m/s. The 1m diameter wheel rotates at 240rpm and absolute velocity makes an angle of 16° with wheel tangent. Determine (1) velocity of whirl at inlet, (2) absolute velocity of water at inlet, (3) vane angle at inlet, and (4) relative velocity of water at entrance. Show the schematic diagram and complete solution with units.
A francis turbine is having a inlet diameter of 2.0 m and an outlet diameter of 1.2 m. Thebreath of the blade is constant as 0.2 m. The runner rotates at a speed of 250 rpm with adischarge of 8 m3/sec. The vanes are radial at the inlet and the discharge is radially outwards atthe outlet. Calculate the angle of guide vane at the inlet and blade angle at the outlet.
Q:/ Discuss the relation betwveen the head pressure and flow rate for the benefits of connecting the pumps in parallel ?
In a francis turbine the vane angle at the entry to the runner is 90degrees, which is rotationg at 75rpm, outer radius is 0.6m and inner radius is 0.3m, velocity at entry and exit to the vanes is 1.8m/s. The water is discharged radially. If the discharge is 1.42m3/s and neglecting friction in the runner calculate: the vane angle at discharge the ouput power developed
In reaction turbine has outer and inner diameters of the wheel as (1m) and (0.5m) respectively. The vanes are radial at inlet and the discharge is radial at outlet and the water enters the vanes at in angle of (10o). Assuming the velocity of flow to be constant and equal to (3m/s) find the speed of the wheel and the vane angle at outlet.
A 5 MW turbine is developed under an effective head of 320 m. The turbine efficiency is85%. Velocity coefficient of the nozzle is 99%.(a)Select which is the appropriate turbine based on effective head. (b)What should be the wheel diameter in meters assuming it is 12 times the diameter of the jet?
A two stage centrifugal pump is designed to discharge water at a total head of 70 m with an overallefficiency of 0.76. The pump runs at 2331.6 rpm. The actual head developed (per stage) is 65% ofthe theoretical head. The flow at the inlet is pure radial. The impeller at the exit has a diameter of D2=0.219m and a width b2=0.0216m .The outlet blade angle is ?= 28°. Determine:1. The flow rate of the pump.2. The output power of the two stage centrifugal pump. Take ρ= 1000kg/m^3g=9.81 m^2/s