Example :- Calculate the power in W/m3 required for mixing an oil of relative density 0.93 and viscosity 18 N.s/m2 in a tank of 15 Cm diameter and 20 Cm height filled to three- fourths of its volume with oil, if the speed of the agitator is 500 rpm. Calculate the speed of agitator if the same mixing is carried out at the same Reynolds number in a doubled volume tank.

Example :- Calculate the power in W/m3 required for mixing an oil of relative density 0.93 and viscosity 18 N.s/m2 in a tank of 15 Cm diameter and 20 Cm height filled to three- fourths of its volume with oil, if the speed of the agitator is 500 rpm. Calculate the speed of agitator if the same mixing is carried out at the same Reynolds number in a doubled volume tank.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the power required per meter of width of stream to force lubricating oil through the gap between two horizontal flat plates under the following conditions: Distance between plates, 6 mm Flow rate of oil per meter of width, 100 m3h Viscosity of oil, 25 cP Density of oil, 0.88 g/cm3 Length of plates, 3 m Assume that the plates are very wide in comparison with the distance between them and that end effects can be neglected.
Calculate the pressure drop through horizontal sanitary stainless steel tubing (9 mminner radius and 1.2 m long) for an apple juice drink that flows with a velocity of 3.13 ms -1 . The density and viscosity of apple juice drink are 1100 kg m -3 and 0.8 x 10 -3 kg m -1 s -1 , respectively. Use the Moody diagram to solve this problem.
The Reynolds number is defined for a pipe as (velocity· diameter· density) / viscosity. What isthe Reynolds number for water flowing at 10 ft/ s in a pipe with a diameter of 6 in? What are itsdimensions?
fluid kimematics mechanical, A crude oil having kinematic viscosity of 0.4×10-4 m2 per second is flowing through a pipe having diameter 0.3 m at the rate of 300 litres per sec. calculate the head lost due to friction for a length of 50 m of the pipe?
An oil is in laminar flow in a ½ in ID tube at 6 gal/min. The oil viscosity is 300 centipoise, and its density is 60 lb/ft³. Calculate the radial position at which the point velocity is equal to the average velocity in inches.A. 0.177B. 0.085C. 0.244D. 0.221
A Pipe used to transport an oil of specific gravity of 0.90 & 0.03poise at a Velocity of 1.6977m/s with a flow rate of 3cubic meter per second. A Pipe was used to conduct a test using water at 20 degree celsius with a velocity of 5.0931m/s. Find the diameter of the prototype. Viscosity of water at 20 degree celsius is 0.01poise
A shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant clearance. If the power required to rotate the shaft is 2204 W, find the viscosity of lubricant oil in the clearance. Take length of sleeve as 150 mm. Assume a linear velocity profile in the fluid film.
Define or describe each type of fluid: (a) viscoelastic fluid, (b) pseudoplastic fluid, (c) dilatant fluid, (d) Bingham plastic fluid.
Water with a dynamic viscosity of 0.892 cP flows in a smooth pipe of diameter, D = 50 mm and length, L = 10 m. The cross-sectional mean velocity is 1.50 m/s. What type of flow is observed? Calculate the discharge, the entrance length and the friction coefficient. Please solve according to question... I need all answers... Thank you
An oil is in laminar flow in a ½ in ID tube at 6 gal/min. The oil viscosity is 300 centipoise, and its density is 60 lb/ft³. Calculate the velocity at the center of the tube in ft/sA. 5.4B. 12.5C. 19.6D. 9.8
liquid (density 800kg/m3, viscosity 10−3 kg/ms) has to be supplied at a mean speed of 2m/s through a pipe of diameter 12.5mm with a surface roughness equivalent to that for structural steel. What is the magnitude of the pressure gradient necessary to achieve this flow? Your answer should have a positive sign and be to the nearest 10 Pa/m. You may wish to use the Moody diagram.
The flow rate of water in a garden hose is measured using the bucket-andstopwatch method. Filling a 5-L bucket takes 75 seconds. If the inner diameter of the hose is 10 mm and the density and viscosity of water are approximately 998 kg m-3 and 0.9 cP, respectively, (a) is the flow inside the hose laminar or turbulent? (b) If the flow rate is adjusted such that the flow is with Re = 2100, how long would it take to fill the same bucket?