A reheat-regenerative engine receives steam at 207 bar and 593°C, expanding it to 38.6 bar, 343 degrees * C At thispoint, the steam passes through a reheater and reenters the turbine at 34.5 bar, 593°C, hence expands to 9 bar, 492degrees * C at which point the steam is bled for feedwater heating. Exhaust occurs at 0.07 bar. Beginning at the throttle(point 1), these enthalpies are known (kJ/kg):ht= 3511.3 h4= 322.9h2 = 3010.0h5 = 2308.1h6= 163.4h2 = 3082.1h3= 3662.5h7= 742.83h7=723.59h4= 3205.4For ideal engine, sketch the events on the Ts plane and for 1 kg of throttle steam, find (a) the mass of bled steam, (b) the work, (c)the efficiency, and (d) the steam rate. In the actual case, water enters the boiler at 171°C and the brake engine efficiency is 75%(e) determine the brake work and the brake thermal efficiency. (f) Let the pump efficiency be 65%, estimate the enthalpy of theexhaust steam.

Answered: Image /qna-images/answer/2d02e307-7a34-4512-a627-419c1184aa48.jpg

A reheat-regenerative engine receives steam at 207 bar and 593°C, expanding it to 38.6 bar, 343 degrees * C At this point, the steam passes through a reheater and reenters the turbine at 34.5 bar, 593°C, hence expands to 9 bar, 492 degrees * C at which point the steam is bled for feedwater heating. Exhaust occurs at 0.07 bar. Beginning at the throttle (point 1), these enthalpies are known (kJ/kg): ht= 3511.3 h4= 322.9 h2= 3010.0 h2 = 3082.1 h5=2308.1 h6 163.4 h7 742.83 h7=723.59 h3= 3662.5 h4= 3205.4 For ideal engine, sketch the events on the Ts plane and for 1 kg of throttle steam, find (a) the mass of bled steam, (b) the work, (c) the efficiency, and (d) the steam rate. In the actual case, water enters the boiler at 171°C and the brake engine efficiency is 75% (e) determine the brake work and the brake thermal efficiency. (f) Let the pump efficiency be 65%, estimate the enthalpy of the exhaust steam.

A reheat-regenerative engine receives steam at 207 bar and 593°C, expanding it to 38.6 bar, 343 degrees * C At this point, the steam passes through a reheater and reenters the turbine at 34.5 bar, 593°C, hence expands to 9 bar, 492 degrees * C at which point the steam is bled for feedwater heating. Exhaust occurs at 0.07 bar. Beginning at the throttle (point 1), these enthalpies are known (kJ/kg): ht= 3511.3 h4= 322.9 h2= 3010.0 h2 = 3082.1 h5=2308.1 h6 163.4 h7 742.83 h7=723.59 h3= 3662.5 h4= 3205.4 For ideal engine, sketch the events on the Ts plane and for 1 kg of throttle steam, find (a) the mass of bled steam, (b) the work, (c) the efficiency, and (d) the steam rate. In the actual case, water enters the boiler at 171°C and the brake engine efficiency is 75% (e) determine the brake work and the brake thermal efficiency. (f) Let the pump efficiency be 65%, estimate the enthalpy of the exhaust steam.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A power plant uses a gas-turbine to produce electricity. Assume that the gas-turbine operates on the ideal Brayton cycle has a pressure ratio of 8. The outside air temperature is 27 C and without preheating, the air is drawn into the compressor. The air compressed in the compressor and its pressure and temperature increase. Thereafter it is supplied into the combustion chamber where its temperature increases to 1023 C at constant pressure. Thereafter, hot air is drawn into the turbine. By considering the air-standard assumptions, determine (a) the gas temperature at the exits of the compressor and the turbine (b) the back work ratio (c) the thermal efficiency
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 2. Determine the quality of steam at the last stage of isentropic expansion in the turbine.
Water is the working fluid in a supercritical ideal reheat cycle. Steam enters the first-stageturbine at 320 bar, 640°C, and expands to 120 bar. After being reheated it enters thesecond-stage turbine at a temperature of 600°C, where is expands to a pressure of 0.06bar. The steam is then condensed until it is a saturated liquid.Question:Determine:(a) The thermal efficiency of the cycle(b) The back work ratio of the cycle
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. Determine the enthalpy of steam entering the reheater.
In a closed cycle gas turbine there is two stage compressor and two - stage turbine. All the components are mounted on the same shaft. The pressure and temperature of air at inlet to the first stage compressor are 1.5 bar and 20 °C respectively . The maximum cycle pressure and temperature are limited to 750 ° C and 6 bar. A perfect intercooling and reheating are used between the compressors and the turbines. A regenerator whose effectiveness is 0.7 was employed. Assuming the compressors and turbines efficiencies as 0.82 , calculate : a . Thermal efficiency of the cycle. b. Mass of working fluid for a power output of 350 kW. Assume the working fluid is air has c = 1.005 kJ / kg K , y = 1.4
power plant has steam entering at 70 bar, 450°C into HP turbine. Steam is extracted at 30 bar and reheated up to 400°C before being expanded in LP turbine upto 0.075 bar. Some portion of steam is bled out during expansion in LP turbine so as to yield saturated liquid at 140°C at the exit of open feed water heater. Considering HP and LP turbine efficiencies of 80% and 85% determine the cycle efficiency. Also give layout and T-s diagram.
In a Rankine Cycle , saturated liquid water at 1 bar is compressed isentropically to 150 bar. First by heating in a boiler and then by superheating at constant pressure of 150 Bar, the water substance is brought to 750 K. After Adiabatic reversible expansion in a turbine at 1 Bar, it is then cooled in a condenser to a saturated liquid. What is the thermal efficiency of the cycle (%)?
In a Thermal Power Plant with a Rankine cycle, superheated steam at 50 bar and 500°C enters the turbine, its isentropic efficiency is 0.8. The condenser that is operating at 0.05 bar delivers saturated liquid to a feed pump, its isentropic efficiency is 0.7. Determine the thermal efficiency of the Power Plant and the mass flow of steam required to generate 50 MW of net power.
Superheated steam at 18 MPa and 560°C enters the turbine of a power plant which operates on actual vapor power cycle. The pressure at the exit of the turbine is 6 kPa, and liquid leaves the condenser at 4.5 bar and 26.0°C. The pressure is increased to 18.2 MPa across the pump. The turbine and pump have isentropic efficiencies of 82% and 77%, respectively. For the cycle, determine (a) the net work per unit mass of steam flow (in kJ/kg), (b) the heat transfer to steam passing through the boiler (in kJ per kg of steam flowing), (c) the thermal efficiency (in %) and the (d) heat transfer to cooling water passing the condenser (in kJ per kg of steam condensed).
A power plant uses a gas turbine to produce electricity. Assume that the gas-turbine operates on the ideal Brayton cycle has a pressure ratio of 8. The outside air temperature is 27 C and without preheating, the air is drawn into the compressor. The air compressed in the compressor and its pressure and temperature increase. Thereafter it is supplied into the combustion chamber where its temperature increases to 1023 C at constant pressure. Thereafter, hot air is drawn into the turbine. By considering the air-standard assumptions, determine (a) the gas temperature at the exits of the compressor and the turbine (b) the back work ratio (c) the thermal efficiency
A power plant uses a gas turbine to produce electricity. Assume that the gas-turbine operates on the ideal Brayton cycle has a pressure ratio of 8. The outside air temperature is 27 °C and without preheating, the air is drawn into the compressor. The air compressed in the compressor and its pressure and temperature increase. Thereafter it is supplied into the combustion chamber where its temperature increases to 1023 °C at constant pressure. Thereafter, hot air is drawn into the turbine. By considering the air-standard assumptions, determine (a) the gas temperature at the exits of the compressor and the turbine (b) the back work ratio (c) the thermal efficiency
1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheatpressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, massflow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following:(a) ideal turbine work(b) ideal pump work(c) theoretical thermal efficiency(d) the steam rate(e) heat rate of the cycle(f) actual work of the pump if pump isentropicefficiency is 89%(g) actual turbine work if turbine isentropic efficiencyis 90%