A resistance of 100ohms, an inductance of 75.0 mH, and a capacitor of 4.0 microF are connected in series with a generator (100 volts at 2500 rad/sec). Find a. the current in the circuit b. the voltage across each circuit component c. the power dissipated in the circuit d. the phase angle between the current and the voltage in the circuit.

A resistance of 100ohms, an inductance of 75.0 mH, and a capacitor of 4.0 microF are connected in series with a generator (100 volts at 2500 rad/sec). Find a. the current in the circuit b. the voltage across each circuit component c. the power dissipated in the circuit d. the phase angle between the current and the voltage in the circuit.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.5P: A 60Hz, single-phase source with V=27730 volts is applied to a circuit element. (a) Determine the...

See similar textbooks

Similar questions

an R-L circuit takes a current of 7amp that lags behind the 231-volt source by 35elec deg. calculate the power factor, power, impedance, resistance, and inductive reactance of the circuit.
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
Subject - Design electrical circuits for single phase AC networks Question - Analyse the methods that improve the power factor of a electrical circuit.
The resistance and reactance of the single-phase 60Hz transmission line conductors are 7.6 ohm and 6.6 ohm respectively. The transmission line delivers 20MW at a power factor of 0.66 lagging to the load with 54kV receiving end voltage. Determine the following a) The inductance of the transmission line in mH b) Sending end power factor c) Percentage voltage regulation d) Percentage Efficiency
For an AC power distribution circuit, the line voltage is 480V and the line current is 53A. The circuit is balanced Delta connected. a. What is the phase voltage measured across each phase?b. What is the phase current for each phase?c. What is the total apparent power drawn by the circuit?d. What is the total apparent power drawn by each phase of the circuit?e. If the circuit has a Power Factor of 85%, what is the total real power drawn from the circuit?
Three-Phase Power Calculations
In the figure, the circuit is given as VRS =√3 . 60V and Zy = 6 + j8. Find the value of C to be connected in order to make the power drawn from the system in a phase 1, to make the load current 1, and to make cos(φ) 1.
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
A series circuit composed of a resistance of 24 ohms, an inductance of 0.09 henry and a capacitance of 8 microfarad, is connected to a 120-volt 50-Hz supply. Calculate (a) the line current, (b) impedance of the circuit, (c) voltage drop, (d) total reactive power, (e) power factor.
The resistance and reactance of the single-phase 60Hz transmission line conductors are 5.4 ohm and 7.4 ohm respectively. The transmission line delivers 45MW at a power factor of 0.65 lagging to the load with 54kV receiving end voltage. Determine the following The inductance of the transmission line in mH Sending end power factor Percentage voltage regulation Percentage Efficiency
Write a report on the Star connection for three phase load experiment using the data/results from the experiment.