A resistor with a coil connected in series A sinusoidal voltage of 120 volts, 25 Hz was applied to the circuit. In the circuit, 70 volts from the ends of the coil, 80 volts from the ends of the resistor and the current drawn from the source is 1.4 A. Calculate the resistance and inductance of the coil in the circuit.

A resistor with a coil connected in series A sinusoidal voltage of 120 volts, 25 Hz was applied to the circuit. In the circuit, 70 volts from the ends of the coil, 80 volts from the ends of the resistor and the current drawn from the source is 1.4 A. Calculate the resistance and inductance of the coil in the circuit.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter24: Resistive-inductive-capacitive Parallel Circuits

Section: Chapter Questions

Problem 10PP: An RLC parallel circuit is connected to 240 volts. The resistor has a power dissipation of 600...

See similar textbooks

Similar questions

The exciting current of an electromagnet is rated at 12 amperes. When connected across a 122 - volt source the current is 14 amperes. Determine the ohms in a resistor which must be connected in series to limit the current to (a) rated value, and (b) 9 amperes.
In a 3-phase, 4-wire, 400/230 V system, a lamp of 200 watts is connected to one phase and neutral and a lamp of 300 watt watts is connected to the second phase and neutral. If the neutral wire is disconnected accidentally, what will be the voltage across each lamp?
Please kindly help me to answer this question. Please provide all the solutions, givens, and formulas used. Thank you very much! The exciting current of an electromagnet is rated at 12 amperes. When connected across a 122 - volt source the current is 14 amperes. Determine the ohms in a resistor which must be connected in series to limit the current to (a) rated value, and (b) 9 amperes.
How is the total load in volt-amperes for lighting purposes determined? See NEC 220.12 __________
The hot water for the heating system for a small factory is supplied by a single boiler. The bolier is locatd in a small building separate form the factory. The power supplied to the bioler is 240-volt single-phase without a netural conductor. At the present time, the small building housing the bioler has no inside lighting. The business owner desires that four 100-watt lamps be installed inside the building. All lamps are to be connected to a single switch. The lamps are to be connected to the present 240-volt sercvice inside the building. How would you accomplish this task? Explain your answer.
An RLC parallel circuit is connected to 240 volts. The resistor has a power dissipation of 600 watts. If the circuit power factor is 75%, what is the total circuit current (IT)?
A 120 – volt AC voltage is applied across a 20 – ohm resistive load. Find values of current, max voltage, peak–to–peak voltage, average voltage, maximum current, peak–to–peak current, average current, and power. draw the circuit diagram
28. A multiwire circuit must consist of conductors connected to ____. Select one: A. THE SAME PHASES B. DIFFERENT BRANCHES C. THE SAME BRANCH D. DIFFERENT PHASES
Three resistors of 50 Ω, 100 Ω and 200 Ω are connected in delta across the three phases of a balanced 100 volts supply. What are the sequence components in the resistors and in thesupply lines?
Determine the current flow is a circuit having a resistance of 5Ω on 110 volts and 240 volts supply.
What is the value of power delivered by 120(Volt) source.
A non-inductive resistance at 15 ohms in series with a condenser takes 5A from 220V mains. What current will this circuit take from 220-volts 25Hz supply?