A rigid horizontal bar ABC is supported by three vertical rods.There is no strain in the rods before load P is applied. Afterload P is applied, the axial strain in rod (1) is ɛ = 580.00 µe3800 mm(1)Determine the deflection of the rigid bar at B and the normal2100 mmstrain in rods (2) if there is a 0.70-mm clearance in the2100 mm(2)(2)connection between rod (1) and the rigid bar before the loadis applied.Try One|VB|mmE2

To find: The value of vB and ε2. Given Data : Axial strain in rod (1) is ε1 = 580.00 με. Length of…

A rigid horizontal bar ABC is supported by three vertical rods. There is no strain in the rods before load P is applied. After load P is applied, the axial strain in rod (1) is & = 580.00 µɛ 3800 mm (1) Determine the deflection of the rigid bar at B and the normal 2100 mm (2) strain in rods (2) if there is a 0.70-mm clearance in the 2100 mm (2) connection between rod (1) and the rigid bar before the load is applied. Try one mm E2

A rigid horizontal bar ABC is supported by three vertical rods. There is no strain in the rods before load P is applied. After load P is applied, the axial strain in rod (1) is & = 580.00 µɛ 3800 mm (1) Determine the deflection of the rigid bar at B and the normal 2100 mm (2) strain in rods (2) if there is a 0.70-mm clearance in the 2100 mm (2) connection between rod (1) and the rigid bar before the load is applied. Try one mm E2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.7.7P: -7 The truss A BC Shawn in the figure supports a horizontal load P1= 300 lb and a vertical load P2=...

See similar textbooks

Similar questions

A prismatic bar in tension has a length L = 2.0 m and cross-sectional area A =249 mn2. The material of the bar has the stress-strain curve shown in the figure. Determi ne t he elongation 5 of the bar for each of the following axial loads: P = 10 kN, 20 kN, 30 kN, 40 kN. and 45 kN. From these results, plot a diagram of load P versus elongation 5 (load-displacement diagram).
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.
A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is/p = 0.5 in, its length is L = 30 in, and its thickness is/ = 0.5 in. Shear force of I' = 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.
An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
A block B is pushed against three springs by a force P (see figure). The middle spring has a stillness K1and the outer springs each have stiffness k^. Initially, the springs are unstressed, and the middle spring is longer than the outer springs (the difference in length is denoted s). (a) Draw a force-displacement diagram with the force P as ordinate and the displacement x of the block as abscissa. (b) From the diagram, determine the strain energy U1 of the springs when x = 2s. (c) Explain why the strain energy E, is not equal to P
The statically indeterminate structure shown in the figure consists of a horizontal rigid bar AB supported by five equally spaced springs. Springs l, 2, and 3 have stiff nesses 3k, 5k. and k, respectively. When unstressed, the lower ends of all Five springs lie along: a horizontal line. Bar AB. which has weight W, causes the springs to elongate by an amount S. (a) Obtain a formula For the total strain energy of the springs in terms of the downward displacement d of the bar. (b) Obtain a formula for the displacement S by equating the strain energy of the springs to the work done by the weight W.
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
A bungee cord that behaves linearly elastically has an unstressed length L0= 760 mm and a stiffness k = 140 N/m. The cord is attached to two pegs, distance/? = 380 mm apart, and is pulled at its midpoint by a Force P = 80 N (see figure). (a) How much strain energy U is stored in the cord? (b) What is the displacement Scof the point where the load is applied? (c) Compare the strain energy (with the quantity PSC12. Note: The elongation of the cord is not small compared lo its original length.
A 4.75-in, outside diameter polyethylene pipe designed to carry chemical waste is placed in a trench and bent around a quarter-circular 90° bend (see figure). The bent section of the pipe is 52 ft long. Determine the maximum compressive strain If the normal strain cannot exceed 6.1 × 10-3 , what is the maximum diameter of the pipe? If d = 4.75 in., what is the minimum acceptable length of the bent section of the pipe?
A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.