end of the left rod and its pin support at C. After attachment, the strain in the left rod is 1.5 x 10-3 What is the length of the gap A? The cross-sectional areas are 300 mm The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are attached to the ends of the bar, there is a gap A between the lower for rod AC and 250 mm2 for rod BD. Use E 200 GPa for steel. 5. is 0.75 m 1.5 m 2 m

end of the left rod and its pin support at C. After attachment, the strain in the left rod is 1.5 x 10-3 What is the length of the gap A? The cross-sectional areas are 300 mm The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are attached to the ends of the bar, there is a gap A between the lower for rod AC and 250 mm2 for rod BD. Use E 200 GPa for steel. 5. is 0.75 m 1.5 m 2 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.2P: A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas....

See similar textbooks

Similar questions

Two separate cables AC and BC support a sign structure of weight W = 1575 lb attached to a building. The sign is also supported by a pin support at O and a lateral restraint in the '-direction at D. (a) Find the tension in each cable. Neglect the mass of the cables. (b) Find the average stress in each cable if the area of each cable is Ae= 0.471 in2.
The triangular block below is subjected to the Loads P=1200 lb and 400 lb. If AB=8 in, and BC is 6in., resolve each load into components normal and tangential to AC.
A steel rod is acted upon by the loading shown below. 50 mm2 is the area of the circular rod. The coupling sizes at B, C, and D are neglected. Use E st = 200 GPa. c) Force in segment CD, PCD=__________ kN, (insert type of force here) d) Total deformation in the assembly, σ = _____________ mm
The rigid bar ABC is suspended from three wires of the same material. The cross-sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P.
1-Determine the elongation of the steel bar 1m long and 1.5 cm cross-sectional area when subjected to a pull of 1500 kg. Take E=2*10 kg/cm ?
The 981-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 339 mm2. Find the location x (in mm) of P that can be safely applied to the bar if the stresses in AC and BD are limited to 119 MPa and 52 MPa, respectively. Express your answer in two decimal places.
Since the suspended mass is m=1500 kg as shown below; Find the force (F) N and the stress N/mm2 in the bar AC. (d=50mm, s=5mm)
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm2. The cross-sectional area of rod (2) is 18 mm2. For a uniformly distributed load of w = 2.4 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 5.25 m.
Determine the largest weight W in N that can be supported by two wires shown in the figure.The stress in either wire is not to exceed 261 Mpa. The cross-sectional areas of wires AB and ACare 258 mm^2 and 320mm^2 respectively.
A force P of 70 N is applied by a rider to the front hand brake of a bicycle(Pis the resultant of an evenly distributed pressure). As the hand brakepivots at A. a tension T develops in the 460-mm Ions; brake cable (Ae=1.075 mm²), which elongates by δ 6=0.214 mm. Find the normal stress 8and strain e in the brake cable.Brake cable, L = 460 mmHand brake pivot A
A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37.5mm left and 60mm north of the center of gravity and induces a stress of 1.75 MPa compression at point A. What is the stress induced at point C & D in MPa
a) Determine the tensile force T’ in the rope on the side connected to joint B: b) Determine the internal compressive normal force ƒBC in the tube BC: c) Determine the horizontal reaction force Rx and the vertical reaction force Ry in joint A: d) Determine the moment M of the center of bar AB: e) Determine the compressive stress σBC in the tube BC: f) Determine the critical load Pc for the tube BC: g) Which of the following statements about the tube BC is correct: A. The tube BC fails due to yielding B. The tube BC fails due to buckling C. The tube BC fails due to both yielding and buckling D. The tube BC is safe against both yielding and buckling h) Pin C has a diameter of 30 mm; calculate the shear stress τ of the pin C, when considering one cross-section for shear stress calculation: