A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P = 35000 lb and the stress in the steel, aluminum, and bronze sections are limited to 20 ksi, 28 ksi, and 18 ksi, respectively, determine the safest area considering the maximum stress in the aluminum. A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in thefigure. Axial loads are applied at the positions indicated. If P = 35000 lb and the stress in the steel, aluminum,and bronze sections are limited to 20 ksi, 28 ksi, and 18 ksi, respectively, determine the safest areaconsidering the maximum stress in the aluminum.4PSteelAluminum BronzeP2.5 ft3 ft2 ft

A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P 35000 lb and the stress in the steel, aluminum, and bronze sections are limited to 20 ksi, 28 ksi, and 18 ksi, respectively, determine the safest area considering the maximum stress in the aluminum. 4P Steel Aluminum Bronze 2.5 ft 3 ft 2 ft

A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P 35000 lb and the stress in the steel, aluminum, and bronze sections are limited to 20 ksi, 28 ksi, and 18 ksi, respectively, determine the safest area considering the maximum stress in the aluminum. 4P Steel Aluminum Bronze 2.5 ft 3 ft 2 ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
Determine the largest weight W in N that can be supported by two wires shown in the figure.The stress in either wire is not to exceed 261 Mpa. The cross-sectional areas of wires AB and ACare 258 mm^2 and 320mm^2 respectively.
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar. Express your answer in MPa.
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
A thick wall cylinder has 50 mm thick and internal diameter of 300 mm. If stress is limited to 30 MPa, determine the maximum internal pressure. A. 8.1 MPa C. 8.3 MPa B. 8.2 MPa D. 8.4 MPa
A steel tube 3.2 cm in internal diameter, 0.25 cm thick and 4 meters long is coveredand lined throughout with copper tubes 0.20 can thick, 7he three tubes are finnlyattached to each other and united at their ends. This compound tube is subjected to axial tension and the stress produced in the steel tube is60 N/mm2. Determine(a) the elongatio~i of the tube(b) the stress in the copper tubes and(c) the load carried by the combined tube.Efor steel = 2.1 x 16 N/mm2 and,E for Copper = 1.1 x 1 o5 N/mm2
mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. The thickness r,-r; is small compared to r; (a) Determine the axial force F in the ring in terms of p, w and r;. Hint: Consider a FBD by cutting the ring+membrane in two. (b) Determine the hoop stress in the ring. (c) Determine the hoop strain in the ring. The modulus of elasticity for the ring is E. (d) Relate the hoop strain to the change in the inner radius of the ring after this pressure is applied, and use this to get the change in the inner radius in terms of p, E, w, r, and ri- (PLEASE ANSWER ASAP AND CORRECTLY)!
The 1021-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 472 mm2. Find the magnitude of P (in N) that can be safely applied to the bar if the stresses in AC and BD are limited to 110 MPa and 51 MPa, respectively. Express your answer in two decimal places.
A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the limiting stress of the bar is 27.24 kPa determine the cross sectional area of the steel square bar and its dimensions.
an acetylene tank consists of a cylindrical body flat at its base and hemisphere at the other end . the thickness of the metal used in tank is 2mm. the tank has a diameter of 250 mm and 1200 mm long. what is the internal pressure of the tank if the allowable stress of the material is 180MPa a. 3.5 kPa b. 6.8 kPa c. 4.2 kPa d. 5.5 kPa