Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown in the figure.The diameter of rod (1) is 1.75 in. and the diameter of rod (2) is 2.50 in, Determine the normal stress in rod 1. Answer in ksi

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown in the figure.The diameter of rod (1) is 1.75 in. and the diameter of rod (2) is 2.50 in, Determine the normal stress in rod 1. Answer in ksi

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.9P: The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10...

See similar textbooks

Related questions

Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure.…

Q: Q1) (A) Two solid circular cross-section bar as shown in the Figure. If the stress in left portion…

A: Given figure A)given data left portion = 150 MN/m² total elongation of the bar = 0.2mm. Young's…

Q: A force of 40 kN is applied to the edge of the member shown in Figure below. Neglect the weight of…

Q: Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in…

A: Given: Diameter of the rod D=50mm Diameter of the pin Dp=40mm Tensile force F=120kN

Q: Q1) (A) Two solid circular cross-section bar as shown in the Figure. If the stress in left portion…

A: A) Given data, Axial load on the bar, P = 160x103 N Stress on the left portion of the bar, σL = 150…

Q: F1. The rigid bar ABC in the figure is supported by a clevis and pin at its right hand side and by…

A: Draw the free-body diagram of the beam.

Q: Problem 3 The two solid circular rods with a 6.6x10*/F are in an initial stress-free state at a…

Q: Two holes have been formed through a steel bar and a centered axial load is applied as shown in the…

A: Given: P = 32 kN Diameter of hole A = 20 mm Diameter of hole B = 50 mm The steel bar is = 100 x 15…

Q: A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If…

Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure.…

A: Bar width, w= 2.25 in Bar thickness, t= 0.375 in Pin diameter, d= 0.775 in Applied load, P= 4800 lb…

Q: The circular rods AB and BC is joined at B and fixed at the wall at A, as shown in the figure.…

A: Given Data LAB =3700 mm, dAB = 26 mm, EAB = 235 GPa, δgap = 10 mm LBC =5700 mm, dBC = 24 mm, EBC =…

Q: A solid circular composite bar (made of aluminum in segment AB, steel in segment BC and Brass in…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

Q: A horizontal load PP is applied to an assembly consisting of two inclined bars, as shown in the…

Q: Complete answer

A: Given Data: Diameter of OB and AB (D) = 100 mm = 0.1 m Radius of disc (r) = 0.5 m Allowable normal…

Q: 1. In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

Q: The strut is supported by a pin at C and a steel guy wire AB. The wire AB has a diameter of 0.2 in.…

A: Given Data: The diameter of wire AB is: d=0.2 in=0.0166 ft The maximum normal stress that the steel…

Q: A clevis-type pipe hanger supports an 8-in.-diameter pipe, as shown in Figure. The hanger rod has a…

A: Given data: W=2000 lb Need to determine the normal stress in the hanger rod, shear stress in the…

Q: determine the tensile stress induced in the bolt.

A: For solution refer below images.

Q: : The homogeneous bar ABCD shown in Fig., is -ported by a cable that runs from A to B around the…

A: ∑FH=0TAB cos 30°=RD sin 50°RD= 1.1305 TAB∑FV=0TAB sin 30°+TAB+TC+RD cos 50°=WTAB sin…

Q: Q1) (A) Two solid circular cross-section bar as shown in the Figure. If the stress in left portion…

A: As per Bartleby's policy in case of multiple questions I can solve only first one. Please repost…

Q: Activity 1: The mass of the homogeneous bar AB shown in the figure is 2000 kg. The bar is supported…

A: Here, m = 2000 kg τallowable = 60 MPa Now, consider below figure: Some important notes: As AB =…

Q: Q2: A rigid platform weighing 53.5 kN is supported by three equally spaced rods. The arrangement is…

A: Given that, Weight of platform, W=53.5 kN,Temperature rise, ∆T=55.5 °C, Consider the properties as…

Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure.…

A: To Find : The average bearing stress produce in the bar . Given : The width is w=2.25 in. The…

Q: 1. Three vertical rods AB, CD, and EF supports s load of 36 kN. Each of the rods AB and CD has a 200…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1)…

Q: A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as…

Q: A circular rod of a diameter of 100 mm is subjected at its free end to force F1 = 50N and F2=(200j -…

A: In this question, three forces are given. The forces are Point force, F1=50i kN Point force,…

Q: A homogeneous 2700 kg bar AB is supported at either end by a cable as shown in the figure. Determine…

A: Given data: Mass of the bar, m = 2700 kg. The cross-sectional area of the bronze cable, AB = 55…

Q: A flat plate with a central hole is subjected to an axial tensile force F of 9.8 KN, as shown in the…

Q: B -1.5 m Figure 2 The -red-brass rod AB of 1.5 m and the aluminium rod BC of 1 m, shown in Figure 1,…

Q: Q3.The pinned members shown in Fig. dawn carry the loads Pand 2P. All bars have cross-sectional area…

A: Take moment about point c The angle at A is

Q: piece of wood, 84 mm by 180 mm, is used as a compression block. The grain of the wood makes a 21.2º…

Q: Rod (2) Rod (1)

A: Given that, Diameter of the circular rod, D=50 mm,Diameter of the pin, d=40 mm,Tensile force applied…

Q: A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If…

Q: Home Work: Determine the largest load P that can be supported by the circular steel bracket shown in…

Q: Droblem 6.4: Each member of the truss in Figure (6.21) is a solid circular rod with diameter d=10…

Q: A clevis-type pipe hanger supports an 8-in.-diameter pipe, as shown in Figure. The hanger rod has a…

A: Given data: W=2000 lb Need to determine the normal stress in the hanger rod, the shear stress in the…

Q: pie Loa A simply supported structure is composed of two members AC and BD (connected by a pin joint…

Q: Rigid bar BC is supported by aluminum rod (1) and bronze rod (2), as shown in the figure. Aluminum…

A: Rods will be subjected to tensile or compressive forces which will act along the axis of the rods.…

Q: and (b) the ratio o 3.51 Fig. shows a circular steel bar. (a) and Fig. square st T applied to them.…

A: Given:r=aπ

Q: Calculate the average stress in section a-a of the junction shown in the figure when applying force…

A: Let us assume that the diameter of the bolt is d in mm.

Q: An axial pull is acting on a bar consisting of two different materials is shown in figure.If the…

Q: Determine the largest weight of the picture frame that can be by the two ropes Tas shown in the…

Q: The pinned members shown in figure carry the loads P and 2P. All bars have cross-sectional area A.…

Q: The round bar ABD of 12 mm diameter is fixed to the wall at its left end and has two arms BE and DC…

A: Diameter of bar = 12 mm. It has two arms at a distance of 55 mm and 95 mm from fixed end Arm length…

Q: O Solve two problems on statically indeterminate structures(strain energy method), two on thin wall…

A: Given: The outer diameter of the steel cylinder is D = 360 mm. The inner diameter of the steel…

Q: At room temperature (20°C) a 0.5-mm gap exists between the ends of the rods shown in the figure. At…

A: For aluminum ;A1=2000 mm2=2×103×10-6 m=2×10-3 m ;E1=75 GPa=75×106 kPa ;α1=23×10-6 /°C ;L01=300…

Q: Q1) The block of weight W in the figure below hangs from the pin at A. The bars AB and AC are pinned…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Two solid cylindrical rods (1) and (2) are joined together at flange B and
loaded, as shown in the figure.The diameter of rod (1) is 1.75 in. and the
diameter of rod (2) is 2.50 in, Determine the normal stress in rod 1. Answer
in ksi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
, An arm A BC lying in a horizontal plane and supported at A (see figure) is made of two identical solid steel bars AB and BC welded together at a right angle. Each bar is 22 in. long. (a) Knowing that the maximum tensile stress (principal stress) at the top of the bar at support A due solely to the weights of the bars is 1025 psi, determine the diameter d of the bars. (b) If the allowable tensile stress is 1475 psi and each bar has a diameter d = 2.0 in,, what is the maximum downward load P that can be applied at C(in addition to self-weight
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
A traffic light and signal pole is subjected to the weight of each traffic signal We = 45 lb and the weight of the road lamp WL= 55 lb. The pole is fixed at the base. Find the principal normal stresses and the maximum shear stress on element B located 19 ft above the base (see figure). Assume that the weight of the pole and lateral arms is included in the signal and lamp weights
-18 through 7.4-25 An clement in plane stress is subjected to stresses ax,ay., and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.4-18 sx= 2900 kPa, sy= 9100 kPar,txy=-3750kPa
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.