A scaled model of a proposed dam is used to predict the flow conditions in the prototype. If thedesign flood discharge over the spillway is (15000+X00) m³/s, calculate the flow rate that shouldbe established in the model to simulate the flow. Also determine the velocity at the specific pointin the prototype, if a velocity of 1.2 m/s is measured at a corresponding point in the model.Assume the scale ratio as 1:50.

Given data Lr=50Qp=15000+X00 m3/sVm=1.2 m/sX=8

Answered: A scaled model of a proposed dam is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The moment of the torpedo control unit in water was tested with a 1:8 scale scale model in a water tunnel of identical properties with a speed of 20 m/s if the measured moment in the model was 14 Nm. calculate 1) Determine the velocity of the prototype using the Reynolds number analogy. 2) Find the ratio of the forces occurring in the model and prototype. Using the analogy of Euler number 3) find the moment that occurred with the prototype.
A certain lake is proposed as a landing area for large jet aircraft. The touchdown speed of 100 mph upon contact with the water is to be reduced to 20 mph in a distance of 1500 ft. If the deceleration is proportional to the square of the velocity of the aircraft throug the water, a=-kv^2 , find the value of the design parameter k . This parameter serves as a measure of the size and shape of the landing gears vanes that plow through the water. Also, determine the time elapsed during the spedified interval. (1 mile=5280 ft)
(a) State the equation describing the condition at streamline boundary for a two-dimensional flow with velocity V and displacement ds Using the equation, derive the equation of a streamline given by Eq. (4.1): ) (See attached images) (b) A steady, incompressible, two-dimensional velocity field is given by Eq. (4.2) : (see attached images) Where: the x- and y-coordinates are in metres and the magnitude of the velocity is in m/s. Calculate the material acceleration at the points of (x = 2, y= 3)
How would I calculate the fluid acceleration along the nozzle centerline. Here, there is steady flow of water through an axisymmetric garden hose nozzle and alongthe centerline the water speed increases from uentrance to uexit . The centerline water speed increases parabolically through the nozzle. What would be an equation for centerline speed u(x), based on the parameters given in the drawing from x = 0 to x = L ?
A 1:7 scale model simulates the operation of alarge turbine that is to generate 200 kW with a flowrate of 1.5 m3/s.What flow rate should be used inthe model, and what power output is expected?(a) Water at the same temperature is used in bothmodel and prototype.(b) The model water is at 25°C and the prototypewater is at 10°C.
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154mm) at point A to 18 in (429 mm) at point B. The volumetric flow rate is 5.0 *3/sec (130 L/s). The respecLve pressures at points A and B are 10 psia (70 kPa) and 7 psia (48.3 kPa). All lossesare insignificant. What are the direcLon of flow and velocity at point A? (A) 3.2 */sec (1 m/s); from A to B(B) 25 */sec (7.0 m/s); from A to B(C) 3.2 */sec (1 m/s); from B to A(D) 25 */sec (7.5 m/s); from A to B
A group of students designed a model drone with a scaling of 1:20 and tested it in a wind tunnel. The wind tunnelhas a flow conditioning system that can produce a mean velocity of 70 m/s, and the drag force measured at this velocityis 350 N. If the drone in real size should operate at 35 m/s,a. determine the pressure inside the wind tunnel,b. determine the drag force that is acting on the real size drone.
A flow is unsteady if the parameters describing that flow do not vary with time. TRUE FALSE
Given the pump(or fan) characteristics in tabular form of up to 20 points of head, η, and flow rate Q. Using EES program or any other software, draw the pump(or fan) characteristic curves, and the system characteristic ( in the form Es= Δz+kQ²) requiring Δz and k input. The program will enable the user to alter the pump (or fan) and system characteristics (Δz and k) to obtain the new curves and establish the operating point.
A liquid is flowing at a volumetric flowrate of Q per unit width down a vertical surface. Obtain form dimensional analysis, the form of the relationship between Q and the film thickness. The flowrate Q is a function of density ρ, viscosity μ, film thickness δ and acceleration due to gravity g. Show that the volumetric flow rate is directly proportional to density if it is known that the flowrate is inversely proportional to the viscosity.
A prototype spillway has a characteristic velocity of 3 m/sand a characteristic length of 10 m. A small model is constructedby using Froude scaling. What is the minimumscale ratio of the model that will ensure that its minimumWeber number is 100? Both flows use water at 20 ° C.
A prototype ocean platform piling is expected to encountercurrents of 150 cm/s and waves of 12-s period and 3-mheight. If a one-fifteenth-scale model is tested in a wavethe channel, what current speed, wave period, and wave heightshould be encountered by the model?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS