A segment of a generator shaft is subjected to a torque T'and an axial force P, as shown in the Figure Q3. The shaft is hollow (outer diameter d2 = 300A mm and inner diameter di = 250 mm) and delivers 1800 kW at 4.0 Hz. (a) If the compressive force P = 540 kN, determine the stresses produced and the state of plane stress on its surface. Calculate the principal stresses and the maximum in-plane shear stress in the shaft. Specify the orientation of the element in each case. (b)

A segment of a generator shaft is subjected to a torque T'and an axial force P, as shown in the Figure Q3. The shaft is hollow (outer diameter d2 = 300A mm and inner diameter di = 250 mm) and delivers 1800 kW at 4.0 Hz. (a) If the compressive force P = 540 kN, determine the stresses produced and the state of plane stress on its surface. Calculate the principal stresses and the maximum in-plane shear stress in the shaft. Specify the orientation of the element in each case. (b)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.6.18P: A prismatic bar is subjected to an axial force that produces a tensile stress ????=65 MPa and a...

See similar textbooks

Similar questions

A hemispherical window (or viewport) in a decompression chamber (see figure) is subjected to an internal air pressure of 85 psi. The window is attached to the wall of the chamber by 14 bolts. (a) Find the tensile force Fin each bolt and the tensile stress (T in the viewport if the radius of the hemisphere is 14 in. and its thickness is 1.25 in. (b) If the yield stress for each of the 14 bolts is 50 ksi and the factor of safety is 3.0, Find the required bolt diameter. (c) If the stress in the viewport is limited to 500 psi, find the required radius of the hemisphere.
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
• - 3 A rectangular plate in biaxial stress (see figure) is subjected to normal stresses u = 67 MPa (tension) and s = -23 MPa (compression). The plate has dimensions 400 X 550 X 20 mm and is made of steel with E = 200 GPa and v = 0.30. (a) Determine the maximum in-plane shear strain ?max in the plate. (b) Determine the change ?t in the thickness of the plate. (c) Determine the change ?t in the volume of the plate.
A propeller shaft subjected to combined torsion and axial thrust is designed to resist a shear stress of 57 MPa and a compressive stress of 105 MPa (see figure). (a) Determine the principal stresses and show them on a sketch of a properly oriented element. (b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
-18 through 7.3-22 An element in plane stress (see figure) is subjected to stresses o, a., and (a) Determine the principal stresses and show them on a sketch of a properly oriented element. (b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element. 7.3-18 a=2I50kPa, ay=375kPa.Txy.=-460kPa
A solid circular bar of steel (G = 78 GPa) transmits a torque T = 360 N - m. The allowable stresses in tension, compression, and shear arc 90 MPa, 70 MPa, and 40 MPa, respectively. Also, the allowable tensile strain is 220 x 10-6, Determine the minimum required diameter d of the bar, If the bar diameter d = 40 mm, what is Tmax?
A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0,5 in, is subjected to internal pressure p = 375 psi, In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure), (a) Determine the maximum tensile stress ctniXand the maximum in-plane shear stress Tmjv in the wall of the cylinder. (b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T\ (c) If 7 = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively, what is the minimum required wall thickness
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A steel pipe is subjected to a quadratic distributed load over its height with the peak intensity q0at the base (see figure). Assume the following pipe properties and dimensions: height L, outside diameter d = 200 mm, and wall thickness f = 10 mm. Allowable stresses for flexure and shear are o~a=125 MPa and Ta= 30 MPa, If L = 2.6 m, Fmd^0ayM (kN/m), assuming that allowable flexure and shear stresses in the pipe are not to be exceeded. If q0= 60 kN/m, find the maximum height Lraajl(m) of the pipe if the allowable flexure and shear stresses in the pipe arc not to be exceeded.
The flat bars shown in parts a and b of the figure are subjected to tensile forces P = 2.5 kN. Each bar has thickness t = 5.0 mm. (a) For the bar with a circular hole, determine the maximum stresses for hole diameters d = 12 mm and d = 20 mm il" the width h = 60 mm. (b) For the stepped bar with shoulder fillets, determine the maximum stresses Tor fillet radii R = 6 mm and R = 10 mm if the bar widths are h = 60 mm and c = 40 mm.
A W 360 x 79 steel beam is fixed at A. The beam has a length of 2.5 m and is subjected to a linearly varying distributed load with maximum intensity q0= 500 N/m on segment AB and a uniformly distributed load of intensity qQon segment EC. Calculate the state of plane stress at point D located 220 mm below the top of the beam and 0\3 m to the left of point B. Find the principal normal stresses and the maximum shear stress at D. Include the weight of the beam, See Table F-l(b), Appendix F, for beam properties.
-3 An element of aluminum in the form of a rectangular parallelepiped (see figure) of dimensions a = 5.5 in., h = 4.5 in, and c = 3.5 in. is subjected to iriaxial stresses = 12,500 psi, o. = —5000 psi, and ci. = —1400 psi acting on the x,i, and z faces, respectively. Determine the following quantities: (a) the maxim um shear stress in the material; (b) the changes ..la, .11. and 1c in the dimensions of the element: (C) the change .IJ’ in the volume: (d) the strain energy U stored in the element: (e) the maximum value of cr1 when the change in volume must be limited to 0.021%; and (f) the required value of o when the strain energy must be 900 in.-lb. (Assume E = 10,400 ksi and v = 0.33.)