A series RC circuit with R = 5 k2 and C = 20 µF has a constant-voltage source of 100 V applied at t = 0; there is no initial charge on the capacitor. Obtain i, UR, VC, and q, for 1> 0. The switch in the circuit shown is closed at 1 = 0, at which moment the capacitor has charge Qo = 500 µC, with the polarity indicated. Obtain i and q, for t> 0, and sketch the graph of q. I kn so v 20 µF

A series RC circuit with R = 5 k2 and C = 20 µF has a constant-voltage source of 100 V applied at t = 0; there is no initial charge on the capacitor. Obtain i, UR, VC, and q, for 1> 0. The switch in the circuit shown is closed at 1 = 0, at which moment the capacitor has charge Qo = 500 µC, with the polarity indicated. Obtain i and q, for t> 0, and sketch the graph of q. I kn so v 20 µF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The triangular voltage pulse shown below is applied to a 200 mF capacitor. a) Write the expressions thatdescribe vc(t) in the five time intervals t < 0, 0 ≤ t ≤ 2 , 2 ≤ t ≤ 6, 6 ≤ t ≤ 8, and t > 8. b) Derive theexpressions for the capacitor current, power, and energy for the time intervals in part (a).
IN THE CIRCUIT SHOWN, CONSIDER THAT V1=20 VDC, R1=1000 Ω, R2=3000 Ω, R3=3500 Ω AND C=1 mF.DETERMINE:A) THE TIME IT TAKES FOR THE CAPACITOR TO REACH ITS FINAL VALUE (5T), WHEN SWITCH 2 (INT 2) IS IN POSITION A AND SWITCH 1 (INT 1) IS CLOSED AT t=0,B) THE ENERGY STORED BY THE CAPACITOR ONCE IT HAS BEEN FULLY CHARGED WITH THE SAME POSITION OF SWITCHES AS ITEM A)C) ONCE THE CAPACITOR HAS BEEN FULLY CHARGED WITH SWITCH 1 CLOSED, SWITCH 2 MOVES POSITION (GOES TO B) AT A NEW t=0. NOW DETERMINE THE VALUE OF THE VOLTAGE ON THE CAPACITOR AT t=3.5 SECONDS
All capacitors were initially discharged. at t = 0, S1 is placed at position 1 and S2 is closed. During this phase, it has been determined that Eth and Rth seen by the equivalent capacitor are, respectively, 20 V and 6.0 kΩ. The time constant is 29 ms. At t = 15 ms, S1 is placed at position 2 and S2 is kept closed. Calculate the equivalent capacitor voltage vT at t = 15 ms. Enter your answer in V rounded to 2 decimal places. At t = 25 ms, S1 is kept at position 2 and S2 is opened. Data: R1 = 5 kΩ, R2 = 3 kΩ, R4 = 2 kΩ, R5 = 20 kΩ, R6 = 12.0 kΩ;
The current flowing through a 10-μF capacitor having terminals labeled a and b is i ab =0.3 exp( −2000t ) Afor t≥0 Given that v ab ( 0 )=0, find an expression for v ab (t) for t≥0. Then,find the energy stored in the capacitor for t=∞..
Consider an LRC series circuit with a resistance of 2.5 ohms, capacitance of 0.1 farad, aninductance of 0.1 henry and electromotive force, volts. Given thatAssume there is no initial charge and no initial current on thecapacitor.The equation of the charge q(t), on the capacitor at any time t q(t)=C1e−5t+C2e−20t+0.05cost+0.2sint . (Do not solve the coefficients). a) State the equation of the current, i(t). b) State the transient and the steady-state current. c) What is the current after a long time.
An RC circuit with a capacitance of 1E-1 farad, and a resistance of 2Ω, has an EMF of E(t)=4cos(t) volts applied to it. a. Find the charge on the capacitor, q(t), with q(0)=6/13, and the subsequenct current, I(t). Solve the problem mathamatically (DE) and try to restrain yourself from solving it using your physics knowledge.
The initial condition current of the inductance is given as iL(0)=1A. circuitBy analyzing the domain of s, we can find the intrinsic solution, forced solution, and exact solution of the current iL(t).find.Element values R1=R2=R3=1Ω, e(t)=Cos 3t Volts,It is L=β H. α=7,β=4
The circuit shown below is an underdamped system, and the current through the inductor has the form iL(t)=e^at ( ) (K1sinwt + K2coswt ) for t≥0 a. Determine the numerical values, including signs, of a and w b. If the initial conditions are iL(0) = 1A and Vc (0) =12V , determine the numerical values, including signs, of K1 and K2 c. Using the numbers determined above, write out the complete expression for iL(t)
The switch in the circuit has been open for a long time before closingat t = 0 s a) Draw the RC circuit for t < 0 and calculate the capacitor voltage just beforethe switching, Vc(0−). b) Draw the circuit after switch has closed (for t > 0), and obtain the Theveninequivalent as seen by the 5 nF capacitor. c) What is the voltage across the capacitor when t → ∞? d) Find the numerical expression for Vc(t) for t ≥ 0 s. e) Find the numerical expression for ic(t) for t ≥ 0 s. f)Find the numerical expression for the power delivered by the voltage controlled current source for t ≥ 0 s.
calculate the time at which the 2 capacitor will have a equal charge. given that the 2 RC circuits (simple) composed of 2mF capacitor, 35kohms resistor, 12V of constant DC source. suppose that at t=0, 1 capacitor is discharged through resistor in its RC circuit (assuming that it is fully charged initially and the DC source is connected) while the other capacitor charged through DC source in its RC circuit through the resistor (assuming that it is uncharged initially).
A current given by i(t)= 3+6 t−−−−−√ (A), where t is measured in seconds, flows through a circuit containing a 14 mF capacitor. Assume the capacitor is initially uncharged. Determine the voltage across the capacitor after 290 ms. Round your answer to 3 significant digits. Value of VC at t= 290 ms is (Volts)
The voltage pulse applied to the 100 mH inductor shown is 0 for t<0 and is given by the expression v(t)=20te−10t V for t>0. Also assume i=0 for t≤0. Sketch the current as a function of time.