A simple beam AB supports two connected wheel loads P and 2P that are distance d apart. The wheels may be placed at any distance x from the left-hand support of the beam. Assume P = 10 kN, d = 2.4 m, and L = 12 m. a) Determine the distance x that will produce the maximum shear force in the beam and the value of the maximum shear force Vmax. b) Determine the distance x that will produce the maximum bending moment in the beam and draw the corresponding bending moment diagram

A simple beam AB supports two connected wheel loads P and 2P that are distance d apart. The wheels may be placed at any distance x from the left-hand support of the beam. Assume P = 10 kN, d = 2.4 m, and L = 12 m. a) Determine the distance x that will produce the maximum shear force in the beam and the value of the maximum shear force Vmax. b) Determine the distance x that will produce the maximum bending moment in the beam and draw the corresponding bending moment diagram

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm. The cross-sectional dimensions of the beam are b1 = 39 mm, d1 = 82 mm, b2 = 23 mm, d2 = 23 mm, and a = 8 mm. For this material, the allowable tensile bending stress is 20 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam.
A gantry crane of weight W=100 Kg moves across a bridge with the length I=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles.
Consider the beam shown. Suppose that w1 = 600 N/m , w2 = 300 N/m . Follow the sign convention. A) Determine the internal normal force at point C. NC = ? B) Determine the internal shear force at point C. VC = ? C) Determine the internal moment at point C. MC = ?
) A simply supported beam of length L=12 m, carrying UDL 10 KN/m in its entire length of thebeam. Draw the Shear Force (S.F) and Bending Moment (B. M) of the beam.Write down the maximum value of B.M
A gantry crane of weight W=100 Kg moves across a bridge with the length /=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles. So it’s wrong answer 1136 N can anyone how to solve for it different ?
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 3.4 ft, P = 25 kips, and w = 1.1 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
When a beam has only uniformly distributed forces applied, the moment diagram consists of piecewise (answer) forces.
| Let's consider a fixed supported beam subjected to a triangular distributed load as shown in the figure below. The equation of the shear force (0 < x = 2m) Is given by: 400 N/m
Uniformly distributed load on a simple support beam with a length of 6 metersMaximum that occurs on the cross section when q is appliedIf bending stress is 337.5MPa,How many kN/m is the equal distribution load q?(However, the cross section of the beam is wide x height = 40mm x)100 mm.)
The maximum normal bending stress in a beam, Mc/I, occurs along the beam where the bending moment is
Question 1) in FIG loading condition is given beam F force F = 65 kN , first distributed load W 1 = 41 kN / m , w 2 distributed load w 2 = 51 kN / m , θ angle θ = 48 ° and L length of L = 5 m . According to this; Question 1-A) B at the point y direction ( B y ) Determine the support reactions. (Enter yourresultwithout writing kN units.) Question 1-B) to the point in y direction ( A y ) Determine the support reactions. ( Enter yourresult without writing kN units.) Question 1-C) to the point in x direction ( A x ) Determine the support reactions. ( Enter yourresult without writing kN units.)
A simply supported beam of length L = 1 m (A = hinged support, B = Roller support) is shown above subjected to a concentrated load P = 1.7 KN, located at a = 0.4m. (A) By neglecting the weigth of the beam determine all support reactions (B) Write the equations for bending moment and shear force at any section along the beam and draw the shear force and bending moment diagram. (C) State the maximal shear force in [N] (D) Determine the magnitude and location of the maximum bending moment in [Nm]