Determine the maximum deflection of a simply supported beam carrying a hydraulic cylinder in a machine used to press bushings into a casting as shown in the figure. The force exerted during the pressing operation in 45 kN. The beam is rectangular, 35 mm thick and 150 mm high, and made of steel (E = 207 Gpa). For deflection: L/2 YB max Between A and B y -PL3 48EI at center - Px. 48E (312-4x2)

Determine the maximum deflection of a simply supported beam carrying a hydraulic cylinder in a machine used to press bushings into a casting as shown in the figure. The force exerted during the pressing operation in 45 kN. The beam is rectangular, 35 mm thick and 150 mm high, and made of steel (E = 207 Gpa). For deflection: L/2 YB max Between A and B y -PL3 48EI at center - Px. 48E (312-4x2)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.5P: A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used...

See similar textbooks

Similar questions

A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A gold-alloy microbeam attached to a silicon wafer behaves like a cantilever beam subjected to a uniform load (see figure). The beam has a length L = 27.5 m and rectangular cross section of a width b = 4.0 m and thickness t = 0.88 m. The total load on the beam is 17.2 N. If the deflection at the end of the beam is 2.46 m is what is the modulus of elasticity Egof the gold alloy? (Use the formulas of Example 9-2.)
A propped cantilever beam, fixed at the left-hand end A and simply supported at the right-hand end B, is subjected to a temperature differentia] with temperature T1on its upper surface and T2on its lower surface (see figure).
A simple beam AB of length L and height h (see figure) is heated in such a manner that the temperature difference 7= T{between the bottom and top of the beam is proportional to the distance from support A: that is, assume the temperature difference varies linearly along the beam: T2- Tt= Tax in which 7"0 is a constant having units of temperature (degrees) per unit distance. Determine the maximum deflection SW9Xof the beam, Repeat for a quadratic temperature variation along the beam, so T2+T1= Tax
Solve the preceding problem for an aluminum column with b = 6,0 in., t = 0.5 in., P = 10 kips, and E = 10.6 × 106 ksi. The defied ion at the top is limited to 2.0 in.
A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression is 400 MPa. The total load P that may be supported by the pad is 900 kN. Using a factor or safely 3.0 with respect to ultimate strength, determine the outer diameter of the pier if the thickness, is of the cross section is 12 mm.
A simply supported slender column is subjected to axial load P = 175 kips applied at distance e = 0,5 in. from joint s A and B (see figure). The column has a circular cross section with an outer diameter of 10 in. and wall thickness of 0.5 in. Calculate the height of the column if the maximum deflection caused by the axial loads is 0,1 in. Assume that E = 29,000 ksi.
A square wood platform is 8 ft × 8 ft in area and rests on masonry walls (see figure). The deck of the platform is constructed of 2-in. nominal thickness tongue-and-groove planks (actual thickness 1.5 in.; sec Appendix CL) supported on two S-ft long beams. The beams have 4 in. × (i in. nominal dimensions (actual dimensions 3.5 in. × 5.5 in.). The planks arc designed to support a uniformly distributed load n ( lb/ft" i acting over the entire top surface of the platform. I be allowable bending stress for the planks is 2400 psi and the allowable shear stress is 100 psi. W ben analyzing the planks, disregard their weights and assume that their reactions are uniformly distributed over the top surfaces of the supporting beams. (a) Determine the allowable platform load Mr. (lb/ft2) based upon the bending stress in the planks. (b) Determine the allowable platform load if-. (lb/ft-) based upon the shear stress in the planks. (c) Which of the preceding values becomes the allowable load alolow on the platform? Hints: Use care in constructing the loading diagram for the planks, noting especially that the reactions are distributed loads instead of concentrated loads. Also, note that the maximum shear forces occur at the inside faces of the supporting beams.
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
A retaining wall (Fig. a) is constructed using steel W-shape columns and concrete panel infill (Fig, b). Each column is subjected to lateral soil pressure with peak intensity q0(Figs, b and c). The tensile and compressive strength of the beam is 600 MPa. Select the most economical W 360 section from Table F-l(b) based on safety factor of 3.0.
A cantileverbeam^Cßsupportstwo concentrated loads Ptand A, as shown in the figure. Calculate the deflections SBand 8Cat points B and C, respectively. Assume Px= 10 kN, P\ = 5 kN, L = 2.6 m, E = 200 GPa, and / = 20.1 x I0ft mm4.
Assume that the deflected shape of a beam AB with immovable pinned supports (see figure) is given by the equation v = - sinx/L, where is the deflection at the midpoint of the beam and L is the length. Also, assume that the beam has constant axial rigidity EA. Obtain formulas for the longitudinal force H at the ends of the beam and the corresponding axial tensile stress t. For an aluminum-alloy beam with E = 10 × 106 psi, calculate the tensile stress twhen the ratio of the deflection S to the length L equals 1/200, 1/400, and 1/600.