A SSB of 8 m span carries a point load of 10 kN at its centre. It also subjects to a UDL of 1 kN/m over its entire span. Find the maximum deflection of the beam. Take E = 200 kN/mm2, I = 200 x 106mm4.

A SSB of 8 m span carries a point load of 10 kN at its centre. It also subjects to a UDL of 1 kN/m over its entire span. Find the maximum deflection of the beam. Take E = 200 kN/mm2, I = 200 x 106mm4.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.2P: A fixed-end beam AB carries point load P acting at point C. The beam has a rectangular cross section...

See similar textbooks

Related questions

Q: A cantilever beam ACB supports two concentrated loads P, and P2, as shown in the following figure.…

A: Draw a diagram for the problem. Here, x is the distance of the cross-section at which the bending…

Q: The vertical deflection at the free end of a stepped cantilever, subjected to moments (M = 10KN-m)…

A: In the given question,L=5+5 = 10 mM = 10 kN-m

Q: _Is4lhVkfYEXQZh-UZqdpqqMbGT. 1/ 2 100% 1) For beam shown below, find reaction forces in supports A &…

Q: . Figure shows a simply supported beam of span 5m carrying two point loads. Find a). The deflection…

Q: * For the RIGID beam shown, find the :deflection at point B 50 kN A B C 2m 3m 3m +0,025 m ID

A: Value of EI is needed

Q: Since the beam AB shown in the figure is P = 60 kN, L = 3 m and E = 200 GPa, find the deflection at…

Q: A cantilever beam has a length L =12 ft anda rectangular cross section (b = 16 in., h = 24 in.).…

A: Calculate the moment of inertia of the beam. I=bh312 Here, I is the moment of inertia of the beam, b…

Q: 6 The coupling rod of a locomotive 2.5 m long is 4 cm broad and 10 cm deep and of rectangular…

A: The coupling rod of a locomotive 2.5 metres long is 4 cm wide, 10 cm deep, and rectangular in…

Q: The cross section of the wood beam is 4 in. by 8 in. Find the value of P for which the downward…

Q: 3. A round shaft, 45 mm in diameter, carries a 3500 N load, as shown in the Figure. If the shaft is…

Q: A beam ABCDE has simple supports at B and D and symmetrical overhangs at each end (see figure). The…

A: Given that ,

Q: A simple uniformly distributed 20 ft. beam carrying a load of 1000 lb./ft. is simply supported at…

Q: A SSB of 8 m span carries a point load of 10 kN at its centre. It also subjects to a UDL of 1 kN/m…

A: Given data as per question Length of beam =8 m Point load =10 KN UDL =1KN/m E = 200 kN/mm2 I = 200 x…

Q: Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute…

Q: 3 typ. 2,8 10 10 13 16,2 15,7

Q: Q5: A steel beam of length 7m is built in at both ends. It has a depth of 500mm and the second…

Q: 1. A semi-infinite steel beam of second moment of area I, = 4.0 × 10° mmª is supported on an elastic…

A: Write the given information.

Q: A simple beam AB of length L supports aconcentrated load P at the midpoint (see gure).(a) Evaluate…

A: Given data as per question The load applied =P Calculations ∑Fx=0HA=0∑Fy=0RA+RB=P…

Q: 3, Using moment area theorem, find the slope and deflection at the free end of cantilever beam if El…

A: Given DataEI=6×106Nm2M=4kNP=16kN BMD and SFD

Q: Compute the slope and deflection of the simply supported beam shown in figure Q2a. Assume value of E…

Q: 711. A cantilever beam BD rests on a simple beam AC as shown in Fig. P-711. Both beams are of the…

Q: Analyze the given structure and find out the slope teta at point B of the steel beam .Take E=200 GPa…

A: E=200 GPa = 200*109 Pa I=60 x106 mm4=60*106*10-12m4=60*10-6m4 AB=8m BC=15m W=2kN=2*103 N

Q: Since the beam AB shown in the figure is P = 60 kN, L = 3 m and E = 200 GPa, find the deflection at…

Q: Quiz: A straight beam ABCD is rigidly built-in at A and D and carries point loads of 5 kN at B and…

A: A built-in beam, also known as the fixed beam is a type os support in which movement of the beam as…

Q: A simply supported beam (E = 12 GPa) carries a uniformly distributed load q =125 N/m, and a point…

Q: 7. A 4.5 m long cantilever beam of hollow circular section of diameters 150.0 mm and 100.0 mm…

Q: 4. A cantilever of length 2m carries a point le kN at its centre. If E = 10 N/mm?and I 10 area…

Q: A simply supported beam of 6 m length with external diameter 150 mm and thickness 15 mm has maximum…

A: Given data: The length of the beam is l=6 m=6000 mm The external diameter of the beam is D=150 mm…

Q: The overhanging beam ABC of span 5.4 m is constructed of a W360 X 216 rolled-aluminium shape. It…

Q: 9.6-5 Calculate the deflections &g and &e at points B and C, respectively, of the cantilever beam…

A: Given, Mo=36kip-inP=3.8kipsL=8ft=96inchEI=2.25×109lb-in2EI=2250000kip-in2 Deflection at point B,…

Q: -30. Calculate the deflection at point C of a beam subjected to uniformly distributedload w = 275…

Q: Q 1. A simple supported beam of span 9m carries two points loads 210 KN & 125 KN at 2m & 6m from…

A: Given:- the span of simple supported beam=9m Uniform distribution load throughout the beam…

Q: A simply supported beam of dimension 4m x 45mm x 90mm, which is subjected to a mid-point load of 130…

Q: A) Calculate the deflection and rotation at point (c) for the beam showing in figure by using unit…

Q: 5. For the beam shown in the figure, determine the slope at A and B and the value of the maximum…

A: Whenever a beam is subjected to load it tends to bend under loading. This is called deflection of…

Q: Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute…

A: Given Data: Moment =2.7 kN.m Uniformly distributed load =300 Nm and it is distributed on 6m length.

Q: A propped cantilever steel beam is constructedfrom a W12 x 35 section. The beam isloaded by its…

A: Given data as per question Length of the beam =11.5 ft E = 30,000 ksi. For W12 x 35 section q =…

Q: 10.4-2 A fixed-end beam AB carries point load P acting at point C. The beam has a rectangular cross…

Q: A simply supported beam is loaded with apoint load, as shown in the figure. The beam is a steelwide…

A: Given data as per question P = 10 kips f L =10 ft a = 7 ft b = 3 ft

Q: Find the deflection at the mid-point BC of the loaded beam as shown in the figure by the double…

Q: Refer to the previous problem. Calculate the resulting maximum positive moment (kN-m). O 77.4 O 96.8…

Q: Problem 4 For the beam shown below, find the value of EIY at 2m from R2. E= 18500MPA and; beam cross…

A: Moment area method is easier method used to find slope and deflection. It is generally used in case…

Q: A fixed-end beam is subjected to a pointload at mid-span. The beam has a rectangular crosssection…

A: given; →P=12KN =12*103N→L=4m =4*103mm→hb=2→E=11GPa =11*103MPa (a)maximum deflection(δmax)=2mm

Q: Q2. Calculate the slope and deflection of a SSB with span 5m carrying a point load of 20kN at 2m…

A: Given Data, There is a simply supported beam. L = Length of the beam = 5 m E = Young's Modulus of…

Q: 2. A simple supported beam of length 4 m carries a point load of 7.25 kN at mid span and a…

Q: bläi 4 For a beam, as shown in the below figure, the deflection at the free end are 8 kN 6kN/m A_c!…

A: A free-body diagram of the above beam is given as, On using force equilibrium in a vertical…

Q: Compound beam ABC is loaded by pointload P 51.5 kips at distance 2a/3 from point A anda triangularly…

A: given; lets take reaction force at A=RAlets take reaction force at…

Q: 3. FIND THE REACTIONS USING THREE MOMENT EQUATION AND SLOPE DEFLECTION EQUATION AND DRAW THE SHEAR…

A: E1=constantMLLLELIL+2MCENTERLLELIL+LRERIR+MRLRERIR+6AQELILLL+6AbERIRLR=…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

A SSB of 8 m span carries a point load of 10 kN at its centre. It also subjects to a UDL of 1
kN/m over its entire span. Find the maximum deflection of the beam. Take E = 200 kN/mm2,
I = 200 x 106mm4.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simply supported beam (E = 1600 ksi) is loaded by a triangular distributed load from A to C(see figure). The load has a peak intensity q0= 10 lb/ ft, and the deflection is known to be 0.01 in, at point C. The length of the beam is 12 ft, and the ratio of the height to the width of the cross section is (h:b) 2:1, Find the height h; and width h of the cross section of the beam.
-5 Calen1ate the deflections S 3a nd
A symmetric beam A BCD with overhangs at both ends supports a uniform load of intensity q (see figure). Determine the deflection SDat the end of the overhang. (Obtain the solution by using the modified form of Castiglianos theorem.)
An aluminum bar having a rectangular cross section (2.0 in. × 1.0 in.) and length L = 30 in. is compressed by axial loads that have a resultant P = 2800 lb acting at the midpoint of the long side of the cross section (sec figure). Assuming that the modulus of elasticity E is equal to 10 × 106 psi and that the ends of the bar are pinned, calculate the maximum deflection and the maximum bending moment Mmax.
A fixed-end beam AB carries point load P acting at point C. The beam has a rectangular cross section (b = 75 mm, h = 150 mm). Calculate the reactions of the beam and the displacement at point C. Assume that E = 190 GPa.
A propped cantilever steel beam is constructed from a W12 × 35 section. The beam is loaded by its self-weight with intensity q. The length of the beam is 1L5 ft. Let E = 30,000 ksi. Calculate the reactions at joints A and B. Find the location of zero moment within span AB. Calculate the maximum deflection of the beam and the rotation at joint B.
A wide-flange beam (W 12 x 35) supports a uniform load on a simple span of length L = 14 ft (see figure). Calculate the maximum deflection max at the midpoint and the angles of rotation Sat the supports if q = 1.8 kips/ft and E = 30 × 106 psi. (Use the formulas of Example 9-1.)
A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.
A heavy object of weight W is dropped onto the midpoint of a simple beam AB from a height h (see figure). Obtain a formula for the maximum bending stress ^ma* due to tne filing weight in terms of h, st, and 5st, where it is the maximum bending stress and Sstis the deflection at the midpoint when the weight W acts on the beam as a statically applied load. Plot a graph of the ratio o"max/ö"it (that is, the ratio of the dynamic stress to the static stress) versus the ratio iifS^r(Let h/S^ vary from 0 to 10.)
A cantileverbeam^Cßsupportstwo concentrated loads Ptand A, as shown in the figure. Calculate the deflections SBand 8Cat points B and C, respectively. Assume Px= 10 kN, P\ = 5 kN, L = 2.6 m, E = 200 GPa, and / = 20.1 x I0ft mm4.
Copper beam AB has circular cross section with a radius of 0.25 in. and length L = 3 ft. The beam is subjected to a uniformly distributed load w = 3.5 lb/ft. Calculate the required load P at joint B so that the total deflection at joint B is zero. Assume that£ = 16,000 ksi.
A cantilever beam AB of length L = 6 It is constructed of a W 8 x 21 wide-flange section (see figure), A weight W = 1500 lb falls through a height h = 0.25 in. onto the end of the beam. Calculate the maximum deflection £m.iy of the end of the beam and the maximum bendini* stress *rm,vdue to the falling weight, (Assume E = 30 X 10 psi,)