A single phase, 60Hz, short transmission line receives 700 MW at 0.95 lagging pr at 327.8 KV from the generator. Using circuit analysis, determine: a. Sending-end current, Is b. Receiving-end voltage, Vr c. Receiving-end current, Ir d. Receiving-end Real, Reactive, and Apparent Power Power loss (real component) in the transmission line e. 6.4 Ω M + Vs j70 Ω Co + ZVR

A single phase, 60Hz, short transmission line receives 700 MW at 0.95 lagging pr at 327.8 KV from the generator. Using circuit analysis, determine: a. Sending-end current, Is b. Receiving-end voltage, Vr c. Receiving-end current, Ir d. Receiving-end Real, Reactive, and Apparent Power Power loss (real component) in the transmission line e. 6.4 Ω M + Vs j70 Ω Co + ZVR

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.25P

See similar textbooks

Similar questions

Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
A short 3 phase transmission line, connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10Megawatts at 0.8 power factor lagging, 30kV at the receiving end. If the minimum transmission line efficiency is to be limited to 96%, estimate the per phase values of resistance and inductance of the line.
Question-2) The parameters of a three-phase transmission line are given as Z = (12.84 + j72, 76)Ω and y = j5, 83x10^-4 mho. At the end of the line, a power of 55 MVA with a power factor of 0.8 is drawn under 132 kV voltage. Accordingly, calculate the line head voltage, active and reactive power values per line, and voltage regulation of the line using the nominal π circuit.7-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the line head voltage (phase-phase voltage) and enter it in the box below. (The value will be entered in kiloVolts. Only the amplitude value of the voltage will be entered. The phase value will NOT be entered!!! Two digits after the comma will be sufficient. )8-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the active power value per line and enter it in the box below. (The value will be entered in MegaWatt. It will be sufficient to take two digits after…
A short 3-phase transmission line connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10 MW at 0.8 lagging power factor at 30 kV at the receiving end. If the minimum transmission efficiency is to be limited to 96%, estimate the per phase value of resistance and inductance of the line.
A 500 kV, 60 Hz uncompensated three-phase transmission line is 500 km long. The line has three ACSR 1113-kcmil (Finch) conductors per phase with parameters Current carrying capability of single ACSR 1113-kcmil (Finch) conductor is 1,110 A. Calculate the theoretical maximum (steady state stability limit) real power that this line can deliver and compare with the thermal limit of the line. Assume VS = VR = 1.0 per unit and unity power factor at the receiving end.
A 69-kV, three phase short transmission line is 16km long. The line has a per phase series impedance of 0.125 + j0.4375 ohms per km. Determine the sending end voltage, voltage regulation, the sending end power, and the transmission efficiency when the line delivers:(a) 70 MVA, 0.8 lagging power factor at 64 kV.(b) 120 MW, unity power factor at 64kV.
A three-phase transmission line is 160 km long and supplies a load of 12 MW at 0.85 powerfactor lagging at 80 kV, 50 Hz. Each conductor has a resistance of 0.275 Ω / km, an inductivereactance of 0.5625 Ω / km and a capacitance to neutral of 0.008625 µF / km. Calculate the line-to-line sending end voltage and the sending end current, using: i. The nominal T method.ii. The nominal Π method. If the sending end voltage remains constant, estimate the approximate rise in voltage at thereceiving end when the load is switched off. Hence calculate the per unit voltage regulation ofthe transmission line.
A short 3-phase transmission line connected to a 33kV, 50 Hz generatingstation at the sending end is required to supply a load of 10 MW at 0·8lagging power factor at 30 kV at the receiving end. If the minimumtransmission efficiency is to be limited to 96%, estimate the per phasevalue of resistance and inductance of the line.
A three phase 220KV, 50Hz transmission line supplies a power of 100MW at a power factor of 0.8 lag at the receiving end. The Series resistance, reactance, and shunt susceptance per phase per Km are 0.082, 0.8 2, and 6 x 10-6mho respectively. Determine the efficiency and regulation for transmission line lengths of 60Km and 200Km (use π)
A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0•85 p.f. lagging by means of a transmission line. The series impedance of a single conductor is (20 + j52) ohms and the total phases-neutral admittance is 315 microsiemens. Shunt leakage may be neglected. Using the nominal T approximation, calculate the line voltage at the sending end of the line. If the load is removed and the sending end voltage remains constant, find the percentage rise in voltage at the receiving end.
A 3-phase overhead transmission line delivers a load of 80 MW at0.8 p.f. lagging and 220 kV between the lines. Its total seriesimpedance per phase and total shunt admittance per phase are 200ohms with an angle of 80 degrees and 0.0013 mho with an angle of90 degrees per phase respectively. Using nominal-T method,determine the following:(i) A, B, C, D constants of the line(ii) Sending end voltage(iii) Sending end current(iv) Sending end power factor(v) Transmission efficiency of the line
A 3-ph, 60 Hz, 200 km long, 220 kV transmission line has per km per phase constants of resistance 0.033 Ω, inductive reactance 0.33 Ω, capacitive susceptance 3.3x10 -6 mho. The load at the receiving end of the line is 500 MW at 0.95 power factor leading and voltage has dropped to 209 kV. Using the PI model, calculate the voltage, current and power factor at the sending end. Please answer in typing format solution please only typing format Please I will like it please reply to