A single phase full converter is connected to a 120 V, 60 Hz supply. It has a RL load having L=6.5 mH, R=0.50 and E = 10 V. The average output voltage VDc =60 V. The output average current is assumed constant equal to Ia. The equivalent circuit is given. The firing angle a would be equal to: 太T。 "I = 1 Select one: O a. 45.26° O b. 80.26° O c. 135° O d. 56.26°

A single phase full converter is connected to a 120 V, 60 Hz supply. It has a RL load having L=6.5 mH, R=0.50 and E = 10 V. The average output voltage VDc =60 V. The output average current is assumed constant equal to Ia. The equivalent circuit is given. The firing angle a would be equal to: 太T。 "I = 1 Select one: O a. 45.26° O b. 80.26° O c. 135° O d. 56.26°

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single-phase full converter supplies an inductive load. Supply voltage is 230 V/50 Hz and the firing angle is 60°. Assuming that the output current is continuous and ripple free and equal to 5 Amp. Determine: (i) Average output voltage, (ii) Supply rms current, (iii)Fundamental power factor, (iv) Distortion factor, (v) Input power factor, (vi) Harmonic factor, (vii) Active and reactive power, (viii) Average and rms values of thyristor current
A 500 kW, 600-V DC, 12-phase rotary converter operates as a direct converter at a full efficiency of 0.92 and a power factor pf 0.93. Calculate the; a) AC voltage between rings, b) AC current drawn from a 12-phase transformer fed supply
A boost converter has an input voltage of 5 V. The average output voltage is15 V and the average load current is 0.5 A. If fs = 25kHz, L = 150 μH and C = 220μF, determine(a)duty cycle (b) inductor ripple current(c) inductor peak current (d) output ripple voltage
The boost converter has the following parameters:Vd= 20V, D = 0.6, R = 12.5, L = 65 μH, C = 200 μF, fs= 40 kHz.Determine(a) output voltage, (b) average, maximum and minimum inductor current, (c) outputvoltage ripple.
A buck converter is supplied from a 50V battery source. Given L=400uH, C=100uF, R=20 Ohm, f=20KHz and D=0.4. Calculate: (a) output voltage (b) maximum and minimum inductor current, (c) output voltage ripple
Design a buck converter that converts input DC 50 V to output 30 V/1 A. (Specifications: Inductor current continuous, output ripple voltage effective 10 mV or less, input 50 Vdc, output 30 Vdc/1 A)
In the figure, R = 13.0 Ω, C = 6.26 μF, and L = 50.0 mH, and the ideal battery has emf = 33.0 V. The switch is kept in position a for a long time and then thrown to position b. What are the (a) frequency and (b) current amplitude of the resulting oscillations? Image is attached, thank you
Please do the following, will upvote! Thank you in advance. Do not copy existing chegg answers, I just want gain Kp calculated. A buck converter is to be designed that will convert 42 V input to 12VDC output Calculate the gain Kp required so that the steady state error of the system for a step input is less than 1 % . Assume the triangle wave peak, Vp, has a value of 5 V for your calculations.
I need help with question 1 (e). 1. Design a buck converter and a resistive load operating in CCM mode with the following specifications:(∆V0)/V0= 0.5 %, Vin = 20 V, f =30 kHz, Duty cycle d=0.4, and R =5.33 Ω. Determine(a) the output voltage and current of the buck converter.(b) the Critical(minimum) inductance for CCM mode(c) select L = 600 µH and find the maximum IL,max and the minimum IL,min inductorcurrents.(d) find the capacitor value that corresponds to (∆V0)/V0= 0.5 % for this buck converter(e) redesign the circuit above to achieve an output ripple voltage of 1 % and an inductor current ripple 10 % at the average load current with the same Duty cycle d, frequency, load Resistance,and Vin. Calculate the accepted new L and C.
Q) A boost PWM converter has the following data: V,=8V, Vo=24V, lo=1.25 A, and f; = 200 kHz. Calculate the minimum inductance required for the converter operation in CCM (Continuous Current Mode). Assume 1) = 95 %. Qs)
A dual slope A/D converter has a reference voltage of 8.000 volts. The time to charge the integrating capacitor is 0.516 ms and the time to discharge it is 0.315 ms. What is the unknown input voltage? a. 4.732 V b. 7.175 V c. 3.751 V d. 5.162 e. 4.88 V
The diagram shown below is a typical tuning circuit. Considering this circuit comprises a transformer (with a coil ratio of 20:1 and an HV side voltage of 240V ), a capacitor of impedance -j20Ω, an inductor of impedance j40Ω, and a 50Ω resistor, determine: the current supplied by the source (0.2228) the impedance seen at the supply (HV side)(21540.55) the power dissipated by the resistor(2.482 watts) the operating power factor of the fitting(0.928 lagging) If the capacitor is now removed from the above circuit and is placed in parallel with the secondary of the transformer, redraw the circuit diagram and recalculate parts a. to d. in question (i). Draw the phasor diagram for both series and parallel RLC circuits in parts (i) and (ii). Discuss the effects of changing the capacitor connection in parallel on the power factor of the circuit. State the benefits of using the transformer in the above circuit. Explain the operating principle of the transformer with particular reference to…