Assume a 30, Y-connected generator with Van 120° volts supplies a A-connected load with Z, jN through a transmission line with impedance of jo.12 per phase. The load is also connected to a A-connected generator with V,"b" = 1Z0° through a second transmission line which also has an = - impedance of jo.12 per phase. Find 1. The load voltage Va'b' 2. The total power supplied by each generator, Sy and S,

Assume a 30, Y-connected generator with Van 120° volts supplies a A-connected load with Z, jN through a transmission line with impedance of jo.12 per phase. The load is also connected to a A-connected generator with V,"b" = 1Z0° through a second transmission line which also has an = - impedance of jo.12 per phase. Find 1. The load voltage Va'b' 2. The total power supplied by each generator, Sy and S,

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.47P: Two three-phase generators supply a three-phase load through separate three-phase lines. The load...

See similar textbooks

Similar questions

5. Solve the following problem: A THREE-PHASE GENERATOR SUPPLIES THREE LOADS IN PARALLEL BY MEANS OF A TRANSMISSION LINE (CONDUCTORS) OF 0.4 + J0.5 OHMS. LOAD No1 5.0 KVA AND POWER FACTOR OF 0.85 BACK. LOAD No2 8.0 KW AND 3.0 KVAR. LOAD No3 6.0 KVA, POWER FACTOR OF 0.80 BACK AND 480 VOLTS. DETERMINE THE GENERATOR PARAMETERS (POWER, POWER FACTOR, OHMS, CURRENT AND VOLTAGE MAGNITUDE).
A 3 phase synchronous generator has a synchronous reactance Xs of 9 Ω perphase, a no-load line to neutral AC voltage E of 12 kV and a line to line terminalvoltage of V of 17.3 kV.(a) Derive the formula for the 3 phase power produced by the generator in terms ofthe power angle δm, |V |, |E|, and Xs. (δm is the angle between E and V ).(b) The power angle δm = 30 degrees. Calculate the 3 phase real power delivered to thegrid at the terminals of the generator.(c) The real power increases when the power angle δm increases, but there is amaximum possible theoretical power that the generator can produce. Calculate themaximum 3 phase real power. Solve A-C
Non-Reactive Loads of 10kW, 20kW and 12kW are connected between the neutral and the red, yellow and blue phases respectively of 3-phase, 4 wire . The line voltage is 400. If a three phase motor is now started ,taking 150 A from the lines at a power factor of 0.3 lagging What should be the total current in each line and the neutral wire? Find the total real and reactive power supplied to the loads
A 3 phase mesh-connected AC generator has a power angle of 15.4 degrees and synchronous impedance of 0.5 + j10 per phase while delivering 300A to its load at a lagging power factor and 13,200 volts line to line. Find the no load emf in volts, line to line.
The following data pertain to two three-phase, parallel-connected, 2,2 kV alternatorsthat are on no load:Machine A: 300 kVA, Xs = 20%Machine B : 500 kVA, Xs = 30%The excitation of A is reduced so as to circulate its full-load current. Assume themachines remain synchronised and calculate:(a) the induced emf of machine A(b) the terminal voltage
Consider the configuration from Problem 1, except that each phase of the transmission line has an impedance of ݆1.5 Ω. a. Determine the line currents. b. Determine the line‐neutral voltage for each branch of the 3Φ load. c. Determine the complex power consumed by the 3Φ load. d. Determine the complex power produced by the 3Φ source. e. Determine the power consumed by the transmission line. f. Determine the load power factor, and the power factor observed by the source. problem 1 : Each leg of a symmetric, Y‐connected, 3Φ load has an impedance of 10∠36.87° Ω, and is connected to A 60 Hz, balanced, positive‐sequence, Y‐connected 3Φ voltage source with Vrms .3Φ source via an ideal transmission line (that is, the connection from the source to the load has zero impedance).
A 250V, 50 Hz single-phase supply feeds the following loads (i) incandescent lamps taking a current of 10A at unity power factor, (ii) fluorescent lamps taking 8A at a power factor of 0.7 lagging, (iii) a 3 kVA motor operating at full load and at a power factor of 0.8 lagging, and (iv) a static capacitor. Determine, for the lamps (incandescent and fluorescent) and motor, (a) the total current, (b) the overall power factor, and (c) the total power. (d) Find the value of the static capacitor to improve the overall power factor to 0.975 lagging.
Two three-generator are parallel at 6.6 kV and delivering 3000 kW at 0.8 pf. The impedance for machine A is 0.5+j10 ohm and for B 0.4+j12 ohm. The excitation of A is adjusted to deliver 150 A at lagging pf. Determine the induced emf of machine A.
A balanced Y load having a load of 3 + j4 Ω in each leg is connected to a three-phase, three wire, Δ-connected generator having a line voltage of 120 V. What Are: Line Voltage (EL), Generator Phase Voltage (), and Load Phase Voltage ()? Load Phase Current (), Generator Phase Current (), and Line Current (IL)? Phase Real Power (P) and Phase Reactive Power (Q)? Total Real Power (P) and Total Reactive Power (Q)?
Electric Machine; Check image, all question there. Consider the above approximate equivalent circuit for IM. A six-pole, 220Volt (line to line), 50Hz, Y connected, three phase IM has the following on a per phase basis: R1=0.5Ω , R2=0.25 Ω, X1=0.75 Ω, X2=0.5 Ω, Xm=100 Ω, Rc=500 Ω The friction and windage loss is 150 W. Determine the following at its rated slip of 3.5% a)Total Impedance(Zt) b)Rotor Copper Loss c)Core loss(Pm) d)Shaft Power(P0) e)Efficiency
A three-phase transmission line receiving end voltage is rated at 21 kV. A load of 1500 KW is connected at the receiving end of the transmission line 70 km long. The parameters of the transmission line are given by r = 0.09 Ω/km and x = 0.8 Ω/km. If the machine is working at 0.65 power factor lagging. Determine a) The series reactance of the transmission line b) Sending end line voltage c) Percentage Voltage regulation d) Percentage Efficiency
Shown are two buses connected via a transmission line. Connected to Bus 1 is a generator(modelled as a voltage source V1), and to Bus 2 is a generator( with Voltage V2) and a load. The line impedance Z = R + jX is not known. Three-phase load is forecasted as 100MW + 60MVar. Generator at Bus 2 is scheduled to deliver 40MW and its excitation is adjusted for the machine to deliver 55 MVar. Voltage at Bus 1 is 241 KV angle 10 deg, while voltage at bus is 230 kV; use V2 as the reference for all angles. 1. What is the current (RMS) in amperes drawn by the load connected to Bus 2? 2. How much real power (in MW) is delivered by the generator connected to Bus 1? 3. What is the total real power loss along the line, in percent of the load? 4. What is the X/R Ratio of the line impedance?