A small county board is composed of threecommissioners. Each commissioner votes on measurespresented to the board by pressing a button indicatingwhether the commissioner votes for or against ameasure. If two or more commissioners vote for ameasure, it passes. Design a logic circuit that takes thethree votes as inputs and lights either a green or a redlight to indicate whether a measure passed.

A small county board is composed of threecommissioners. Each commissioner votes on measurespresented to the board by pressing a button indicatingwhether the commissioner votes for or against ameasure. If two or more commissioners vote for ameasure, it passes. Design a logic circuit that takes thethree votes as inputs and lights either a green or a redlight to indicate whether a measure passed.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

i)Simplify the expression in the image shown below using the Kamaugh map ii)Illustrate the results gotten on a logic circuit
A limited company has four directors A, B, C, D holding 35%, 30%, 20% and 15% of the shares respectively. A major decision must have a support of minimum 60% of the stock. Design a combinational logic circuit for the voting in the company. Use a decoder to design the circuit. Show the truth table of the circuit.
Prove (A+B)(A+C) = A+BC. Draw the logic circuit diagram for both sides
There are 5 gates in a metrobus, 1 of which is to get on and 4 to get off. The number of passengers inside is desired to be seen on the LCD connected to the P2 port. Get-on gate is controlled by the P0.2 while get-off gates are controlled by the P0.3, P0.4, P0.5, and P0.6. The sensors generate Logic-1 while passing passengers. Since the passenger carrying capacity of the metrobus is 294, if the number of passengers exceeds the number of 294, the warning LED connected to the P0.7 pin is required to light up. Since other pins of P0 are used for other purposes, it is not desired to be changed. Can you write the answer with assembly code using 8051 - AT89S8253 architecture?
a) Design a logic circuit with three inputs A, B, C and an output that goes LOW only when A is HIGH while B and C are different. Draw and upload the circuit if you can, or at least describe it in words. b) Which logic gates produce a 1 output in the disabled state? c) Which logic gates pass the inverse of the input signal when these gates are enabled? d) What is the normal resting state of the SET’ and RESET’ inputs of a latch circuit (the prime is same as bar)? What is the active state of each input? e) What is the normal resting state of the NOR latch inputs? What is the active state?
The expression given is an SOP simplification of which logic circuit?
A LED is connected to the output of the Q logic system and if the A, B and C signals given below are applied to the electronic circuit formed, create a truth table and show at what time intervals the LED will light up.
A combinational logic circuit that compares between two 2-bit numbers A (A1 A0) and B(B1 B0) is designed. Output F is high when ? > ? and low when ? < ?. 1) Are there any undefined outputs? If there are any undefined outputs what are the inputs?
A coin-operated cold drink dispenser will provide cold drink (D) under the following conditions: The correct coin (C) is inserted AND A paper cup is in position (P) AND The selector is set t Orange (O) OR Sprite (S) OR Lemonade (L) Write the Boolean expression for the output of the dispenser. Represent the operation of the dispenser in logic circuit 4 get a logic circuit to mimic corporate checking system for operators of a company
Which of the following statements accurately represents the best method of logic circuit simplification? a. Actual circuit trial and error evaluation and waveform analysis b. Boolean algebra and actual circuit trial and error evaluation c. Karnaugh mapping and circuit waveform analysis d. Karnaugh mapping and Boolean algebra
Create a logic diagram out of this boolean expression. CD+BD+BC+AD+AC+AB Note: All inputs A B C and D must be together.
Book used is Digital Logic with Verilog Design by Brown & Vranesic. Study the counting circuit diagram below and answer the following questions: a. Based on the circuit drawing, is the Clock Positive-Edge Triggered or Negative-Edge Triggered? b. How was this determination made? c. What are the minimum and maximum valkues of the circuit? Explain. d. There are 3 grayed out boxes we refer to this symbolic use as _____________. Why are these used in circuit design?