Design a sequence detector that detects the sequence 1010. This detector has one input X, and one output Y. The output Y is set to 1 only when the input sequence for X is a 0 followed by a 0 by followed by another 0 and finally followed by a 1, detecting the sequence, otherwise the output Y is set to 0. Using D-type flip-flops in designing this detector. 1.Show the state diagram 2.Show the state table 3. Draw the logic diagram of the designed device

Design a sequence detector that detects the sequence 1010. This detector has one input X, and one output Y. The output Y is set to 1 only when the input sequence for X is a 0 followed by a 0 by followed by another 0 and finally followed by a 1, detecting the sequence, otherwise the output Y is set to 0. Using D-type flip-flops in designing this detector. 1.Show the state diagram 2.Show the state table 3. Draw the logic diagram of the designed device

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

For the standard synchronous decade up counter circuit using JK flip-flops, shown in Floyd, the counter starts in the state decimal 11 after the power is first turned on. Determine the next state of the counter in decimal.
3-Design and draw the circuit of a synchronous counter that counts in a continuous loop as (...-0-2-4-6-0-2-4-...) using T-type flip flops. When unintentionally encountered numbers that are not in the counting index, have the counter point to the nearest number in the counting index. Take minterms (SOP) as reference in your transactions. The circuit you have drawn is understandable
You are tasked to design a control unit for a light display. The light display design has three light components, see Figure 4.1a. Design a state machine that will control the sequence of the display (see Figure 4.1b). Your design should include three edge triggered D flip-flops, with each of the components controlled by one D flip-flop. Individual states of the sequence have been pre-defined (see Figure 4.1b), and the sequence should be run as an infinite loop. Any unused states can be treated as Don’t Cares. Your answer should include the following: a) A state diagram for the monitoring unit. b) A transition table. c) Based on the transition table in part b), use Karnaugh Maps to derive input equations the three D flip-flops. Show the full circuit design for the display control unit. Use a block diagram for each D flip-flop.
5.10 Implement a 4-bit up counter with T flip flops by doing the following. Up counter means countingfrom 0000 to 1111. Down counter means counting from 1111 to 0000.[1] How many flip flop is needed to implement this counter?[2] Derive a state diadram for this counter.[3] Derive a truth table for this counter with T flip flop[4] Develop state input equations[5] Sketch a logic diagram for this counter.
Design an Octal Counter with D flip-flops.a) Draw the state diagramb) Draw the state tablec) Draw the counter circuit
Design a sequential circuit with two flip-flops A and B, and one input x_in. When x_in = 0, the state of the circuit remains the same. When x_in = 1, the circuit goes through the state transitions from 00 to 01, to 11, to 10, back to 00, and repeats. a. Using D Flip-Flop. b. Using JK Flip-flop.
1. If a j-k flip flop has the j and k inputs connected to 5volts while being clocked it will: A. Toggle B. Enter the race condition C. Be set D. Be reset 2. What is the minimum number of J-K flip-flops needed to construct a divide by eight circuit? A.4 B.3 C.8 D.2
Question 2: The circuit below is a synchronous sequential circuit based on D-type flip-flops (DFFs): (a) Write the excitation and state equations for the two DFFs. (b) Express the output equation for the outputz. (c) Determine the present and next state table of the circuit. (d) By using the result obtained in (c), sketch the circuit using JK flip-flops (JKFFs).
Design a traffic light system with 2 push button input and 3 light output (red, orange, green) using sequential or counter circuit using counters and use flip-flops (use logic.ly for design).
Convert a single J-K flip flop to a T-flip flop. Include all steps involved. What is the next count if the counter started with 000 and 011 (unused states)? i want the anwer for the second qustion
1. Asequential circuit with two D flip-flops A and B, two inputs, x and y ; and one output zis specified by the following next-state and output equationsA(t + 1) = xy’+ A’y‘B(t + 1) = xB+ B‘+ xB’z = A‘B(a) Draw the logic diagram of the circuit.(b) Draw the corresponding state diagram. 2.A sequential circuit has two JK flip-flops A and B and one input x . The circuit is describedby the following flip-flop input equations:JA = A‘x’+ B’KA = A’+ By’JB = A’+ xB’KB = AB+ xy’z = B‘y‘ + Bx‘y’(a) Draw the logic diagram(b) Draw the state diagram of the circuit.
Design a state machine that will control the sequence of the display (see Figure 4.1b). Your design should include three edge triggered D flip-flops, with each of the components controlled by one D flip-flop. Individual states of the sequence have been pre-defined (see Figure 4.1b), and the sequence should be run as an infinite loop. Any unused states can be treated as Don’t Cares. c) use Karnaugh Maps to derive input equations the three D flip-flops. Show the full circuit design for the display control unit. Use a block diagram for each D flip-flop.