A solid circular rod with a diameter d= 18 mm is shown in Figure Q-3. The rod is made of an aluminum alloy that has an elastic modulus E = 72 GPa and a Poisson's ratio v = 0.32. When subjected to the axial load P, the diameter of the rod decreases by 0.025 mm. For a factor of safety of 1.75,

A solid circular rod with a diameter d= 18 mm is shown in Figure Q-3. The rod is made of an aluminum alloy that has an elastic modulus E = 72 GPa and a Poisson's ratio v = 0.32. When subjected to the axial load P, the diameter of the rod decreases by 0.025 mm. For a factor of safety of 1.75,

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.4P: A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to...

See similar textbooks

Related questions

Q: Rod AB is fixed to a smooth collar D, which slides freely along the vertical guide shown in (Figure…

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 4500 N…

A: The Point A will be subjected to tensile stress due to bending stress generated by force F.bending…

Q: A nylon [E = 2.48 GPa; v = 0.4] rod (1) having a diameter di = 50 mm. is placed inside a Q-5 steel…

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure: Q 3(a). Axial…

A: Given details: Esteel=200 GPaEBronze=80 GPaEAluiminium=70 GPaLSteel=1 mLBronze=2 mLAluiminium=1.5…

Q: H.W.7: A pin-connected structure is supported as shown in Figure load P is applied. Bar (1) is made…

A: Given data Bar (1) made of brass [oy = 18,000 psi; E = 17 x 106 psi], length of L = 8.0 ft. Bar…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

A: Diameter of each section can be calculated by calculating net force on each section . 1. Calculate…

Q: A 260 mm bar AB with a rectangular cross section of 17 × 30 mm, consists of two aluminium layers…

Q: 2.10-3 A flat bar of width b and thickness 1 has a hole of diameter d drilled through it (see…

A: Given data: - The width of the bar is b. The thickness of the bar is t. The diameter of the hole…

Q: A copper rod of 50mm diameter is surrounded by a steel tube of 100mm external diameter, the ends…

Q: a) The material is 2024-T4 aluminum with a yield strength of 47 ksi b) The rod length L=6 in and arm…

Q: 2. A rigid bar ABDE is being attached to a wall via a pin at A and alloy steel rod BC (E = 250 GPa).…

Q: b) A steel column AB is fixed at its base and is braced at its top by cables as shown in Figure Q4…

Q: A butt connection is shown in the following figure. Plates is Q235 steel; 8.8 Grade M16 high-…

A: Load bearing capacity Loadbearing capacity is the maximum ability of a structural member or…

Q: . Illustrated in the figure is a 1.5 in diameter steel countershaft that supports two pulleys.…

Q: The rod shown in the figure is made of (1020 HR steel). The applied static loads, in the…

Q: A stepped 100 N-m as shown in figure below. Modulus of rigidity of material is 90 GPa, then angle of…

A: Given data: Torque, T=100 N-m G=90 GPa

Q: figure is attached to a shaft with a diameter of d=50mm with a welded seam closed on both sides with…

A: Given:F=8 kNd=50 mm or 0.05 mr=d2=502=25 mm or 0.025 ma=4 mm or 0.004 mτ=180 N/mm2

Q: A vertical steel bar shown in figure Q1 is subiected to a compressive load of 75 kN. If the stress…

Q: 5. An angle bracket ABC is restrained by a high- strength steel wire CD, and it supports a load P at…

Q: A solid circular rod with a diameter d= 16 mm is shown in Figure Q-3. The rod is made Q-3 of an…

A: (a) Calculate the lateral strain by using the decrease in diameter given in the question. Write the…

Q: he bar shown in the following figure has a diameter of 20 mm and is subjected to a force P = 2750 N…

A: Given:d=20 mmP=2750 NF=14000 NSyt=480 MPaPoint A will be subjectd to tensile stress due to bending…

Q: The metallic hollow pipe shown in Figure Q1 is fixed at both its ends, and is under axial…

Q: A portion of the stress-strain curve for a stainless steel alloy is shown in Figure Q-2. A 350 mm…

Q: The A-36 steel rod BC as shown in Figure Q3 has a diameter of 5X mm ( X is a last digit of your…

A: (a) Write the given data. d=5X=53 mmσY=260 MPaEs=210 GPaFOS=3

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: A rod as shown in Figure Q1 is fixed to a rigid wall at its end point A and is made of a steel tube,…

A: Answer: (i) The minimum diameter of rod d is 43.245 mm. (ii) The angle of twist of point B relative…

Q: 3 The A-36 steel rod BC as shown in Figure Q3 has a diameter of 50mm and is used as a strut to…

Q: Problem 8 Problem 8.2-6 A spherical steel pressure vessel (diameter 480 mm, thickness 8.0 mm) is…

A: Given data as per question Diameter =480 mm Thickness = 8.0mm E=205 Gpa V =0.30

Q: 3. A hollow cylindrical cast iron column 200 mm external diameter and 25 mm thick is 6 metres in…

A: Given, External diameter, Do=200mmThickness, t=25mmInternal diameter, Di=150mmLength of the column,…

Q: 3 The A-36 steel rod BC as shown in Figure Q3 has a diameter of 5X mm (X is a last digit of your…

A: For solution refer below images.

Q: The horizontal member shown in the figure is loaded by 25 kN at E. It is supported by steel…

A: Permissible stress is stress, which produces due to pressure or forces which does not exceed the…

Q: Consider the steel arm assembly in the figure below that supports load R. Using the Coulomb-Mohr…

A: For solution refer below images.

Q: Q-1 A solid circular rod with a diameter d= 18 mm is shown in Figure Q-3. The rod is made of an…

Q: A portion of the stress-strain curve for a stainless steel alloy is shown in Figure Q-6. A Q-6 350…

Q: A portion of the stress-strain curve for a stainless steel alloy is shown in Figure Q-2. A 350 mm…

A: Write the expression of the normal strain.

Q: Problem (8) The rigid bar ABC in the figure is Figure P-268 pinned at B and attached to the two…

A: Given data as per questionfor steelL=0.9 mA=300mm2E=200×109 Nm2α=11.7μm/(m0c)Distance between AB=0.6…

Q: A steel railroad track is laid at a temperature of 15°F with gaps of 0.18 inchbetween the ends of…

Q: 2.5-3 A rigid bar of weight W = 750 lb hangs from three equally spaced wires, two of steel and one…

A: Given dataWeight of the rigid bar W = 750lbDiameter of wires d = 0.125 inchModulus of elasticity of…

Q: P1.6 Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in Figure…

Q: ILLUSTRATION AND SOLUTION Problem 1: A steel rod with a cross - sectional area of 150 mm2 is…

Q: The figure below are cables ( circular section) supporting a 48 kN. Find the axial stress of each.…

Q: Situation 2 -A steel column of hollow circular cross section is supported on a circular steel base…

Q: The cantilevered bar in the figure is made from a ductile material and is statically loaded with Fy…

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 1500 N…

A: Given:F=500 NP=1500 Nd=40 mmSyt=60MPaI=π64*404 =125663.70 mmStresses acting at point A:The Force…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

A: Please refer to the detailed solution given below, Answers- Minimum diameter required for each rod…

Q: Shown below is a rigid beam ABC that is connected by pinned connections to rod (1) at A, rod (2) at…

A: Given Data: The length of rod 1 is l1= 250 mm. The length of rod 2 is l2 =500 mm. The diameter of…

Q: A torsional moment T = 5,382 Nm and a load P = 55,253 N are applied at the same time to a circular…

Q: A 260 mm bar AB with a rectangular cross section of 17 x 30 mm, consists of two aluminium layers…

A: The structural configuration given above is statically determinate because the there are two…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

i want full answer with the all steps

A solid circular rod with a diameter d= 18 mm is shown in Figure Q-3. The rod is made of
an aluminum alloy that has an elastic modulus E = 72 GPa and a Poisson's ratio v = 0.32. When
subjected to the axial load P, the diameter of the rod decreases by 0.025 mm. For a factor of safety
of 1.75,

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A flat bar of width b and thickness t has a hole of diameter d drilled through it (see figure). The hole may have any diameter that will fit within the bar. What is the maximum permissible tensile load Pmaxif the allowable tensile stress in the material is st?
A hollow circular tube T of a length L = 15 in. is uniformly compressed by a force P acting through a rigid plate (see figure). The outside and inside diameters of the tube are 3.0 and 2.75 in., respectively. A concentric solid circular bar B of 1.5 in. diameter is mounted inside the lube. When no load is present, there is a clearance c = 0.0I0 in. between the bar B and the rigid plate. Both bar and tube are made of steel having an c[autoplastic stress-strain diagram with E = 29 X LO3 ksi and err= 36 ksi. (a) Determine the yield load Pt- and the corresponding shortening 3yof the lube. (b) Determine the plastic load Ppand the corresponding shortening Spof the tube. (c) Construct a load-displacement diagram showing the load Pas ordinate and the shortening 5 of the tube as abscissa. Hint: The load-displacement diagram is not a single straight line in the region 0 ^ P ^ Pr
Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.
Around brass bar of a diameter d1= 20mm has upset ends each with a diameter d2= 26 mm (see figure). The lengths of the segments of the bar are L1= 0.3 m and L2= 0.1 m. Quarter-circular fillets are used at the shoulders of the bar, and the modulus of elasticity of the brass is E = 100 GPa. If the bar lengthens by 0.12 mm under a tensile load P, what is the maximum stress ??maxin the bar?
The figure shows an idealized structure consisting of a rigid bar with pinned connections and linearly elastic springs. Rotational stiffness is denoted R, and translational stiffness is denoted . Determine the critical load PCTfor the structure from the figure part a. Find PCIif another rotational spring is added at B from the figure part b.
A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
The assembly shown in the figure consists of a brass core (diameter d:= 0.25 in.) surrounded by a steel shell {inner diameter d2= 0.23 in., outer diameter di= 0.35 in.}. A load .P compresses the core and shell that both have a length L = 4.0 in. The module of elasticity of the brass and steel are Eb=15 X 10fi psi and Es= 30 X 10fi psi, respectively. (a) What load P will compress the assembly by 0.003 in? (b) IF the allowable stress in the steel is 22 ksi and the allowable stress in the brass is 16 ksi. what is the allowable compressive load Pallow? (Suggestion: Use the equations derived in Example 2-8.)
A trimetallic bar is uniformly compressed by an axial force P = 9 kips applied through a rigid end plate (see figure}. The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter of L.25 i n., the brass tube has an outer diameter of 1.75 in., and the copper tube has an outer diameter of 2.25 in. The corresponding modulus of elasticity are f, = 30, 000 ksi, Eb= 16,000 ksi, and E = 18,000 ksi Calculate the compressive stresses ers, ab, and cin the steel, brass, and copper, respectively, due to the force P.
A horizontal rigid bar ABC is pinned at end A and supported by two cables at points B and C. A vertical load P = 10 kN acts at end C of the bar. The two cables are made of steel with a modulus elasticity E = 200 GPa and have the same cross-sectional area. Calculate the minimum cross-sectional area of each cable if the yield stress of the cable is 400 MPa and the factor of safely is 2.0. Consider load P only; ignore the weight of bar ABC and the cables.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A compressive load P is transmitted through a rigid plate to three magnesium-alloy bars that are identical except that initially the middle bar is slightly shorter than the other bars (see figure). The dimensions and properties of the assembly are as follows: length L = 1.0 m, cross-sectional area of each bar A = 3000 mm", modulus of elasticity E = AS GPa, and the gap s = 1.0 mm. (a) Calculate the load Ptrequired to close the gap. (b) Calculate the downward displacement 5 of the rigid plate when P = 400 kN. (c) Calculate the total strain energy V of the three bars when P = 400 kN (d) Explain why the strain -energy V is not equal to PS/2. Hint: Draw a load-displacement diagram.
A long slender column ABC is pinned at ends A and C and compressed by an axial force F (sec figure). At the midpoint B, lateral support is provided to prevent deflection in the plane of the figure. The column is a steel wide-flange section (W 250 × 67) with E = 200 GPa. The distance between lateral supports is L = 5.5 m. Calculate the allowable load P using a factor of safety n = 2.4, taking into account the possibility of Eu 1er buckling about cither principal centroidal axis (i.e., axis 1-1 or axis 2-2).