A solid steel shaft 4 feet long is stressed to 18 ksi at 18 Hz when twisted through 3 degrees. Use G = 12 x 10^6 psi. DETERMINE: A. Compute the shaft diameter (in inches) B. the torque applied in the shaft (in lb-ft). C. What power (in Horseposer) can be transmitted by the shaft?

A solid steel shaft 4 feet long is stressed to 18 ksi at 18 Hz when twisted through 3 degrees. Use G = 12 x 10^6 psi. DETERMINE: A. Compute the shaft diameter (in inches) B. the torque applied in the shaft (in lb-ft). C. What power (in Horseposer) can be transmitted by the shaft?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: Two cars moving on the same direction have a velocity of 90 ft/sec. Car A is 100 feet behind car B.…

A: Given data the velocity of cars A and B are 90 ft/sec To determine required acceleration of…

Q: The complex mechanical impedance in a pipe at (x 0) is Z =-jp.cS Cot(kL) if the other end (x = L) of…

A: Answer: Each of the impacts considered in this study is symbolized by a different F-value, for a…

Q: 0.6 m 1 m 1200 N.m d,= 30 mm- B A 800 N.m d, = 60 mm Figure 4 c) Consider a shaft in Figure 4 is a…

Q: A steam turbine has an inlet of 3 kg/s water at 1200 kPa and 350°C with a velocity of 15 m/s. The…

Q: Write a report on Reynolds Number's experience. Where

A: Within a fluid exposed to relative internal movement due to varying fluid velocities, the…

Q: A student built a contraption. The student has a 40 kg weight that they need to attach to one of the…

A: This question is based on the concept of kinetic acceleration

Q: Find the general solution for the following first order D.Es? b) x*dy + (y? - xy)dx 0 d) (x + xy -…

Q: A rod hanging from a support whose unit mass is 3900 kg/ m³ has a cross sectional area of 400 mm?…

Q: Water at 20∘C flows through the 20-mm-diameter galvanized iron pipe such that it discharges at C…

Q: Problem (4.7): For the thin-wall tubular sections shown in Figure (4.28); (a) Determine the maximum…

Q: While exploring the wooded areas by York University, a student found a mysterious hatch with a…

Q: An insulated steam pipe located where the ambient temperature is 32C, has an inside diameter of 40…

A: Answer: The heat loss per unit length of pipe is 67.1804 Watt.

Q: A small ship capable of making a speed of 6.8 knots through still water maintains a heading due east…

Q: A container is occupied by a ten kg water and four kg vapor at 0.88 MPa. Determine (a) its…

Q: An open tube mercury manometer is used to measure the pressure in an oxygen tank. When the…

Q: The shaft below is an engine component that is rotating. It is machined from an unknown ductile…

A: Solution: Given Data: Sut=900 MPaR=0.99f=0.9d=0.1 m

Q: (2) A diesel engine developing 1,850 hp at 105 rpm is used on a ship to drive the propeller. The…

A: Shaft and axle are machine members which revolve in the machine like pulley and gears etc. As the…

Q: 9. Give the balanced chemical equation for the decomposition of C2H«O.

Q: The mass center G of the 1400-kg rear-engine car is located as shown in the figure. Determine the…

Q: Cyllndrical tanks are filled with a liquid as shown below. a) ( Calculate the time to completely…

Q: 20- Air enters a nozzle steadily at 280 kPa and 77°C with a velocity of 50 m/s and exits at 85 kPa…

Q: 2. Show how to derive the thermal resistance of the spherical layer against heat conduction as…

A: Heat conduction equation for steady state condition is written and further integrated to get the…

Q: 4. A reservoir of glycerin has a mass of 1200 kg and a volume of 0.952 m³. Find the glycerin's…

Q: ᴀ ꜱᴜᴘᴘʟʏ ᴛᴀɴᴋ ʜᴀᴠɪɴɢ 14ᴍ ʟᴏɴɢ ᴀɴᴅ 1.7ᴍ ᴅɪᴀᴍᴇᴛᴇʀ ɪꜱ ᴜꜱᴇᴅ ᴛᴏ ꜱᴛᴏʀᴇ ꜰᴜᴇʟ ᴏɪʟ ᴡɪᴛʜ 34° ᴀᴘɪ ᴀᴛ 110 °ᴄ. ɪꜰ…

Q: The correction factor should be greater than 1. True or False?

Q: 1. A museum of modern art is displaying an irregular 426-N sculpture by hanging it from two thin…

A: Given W=426N

Q: Create a situation illustrating the cases identified below. (Thermodynamics) a. a process where the…

Q: As part of an industrial pipe system a 6-meter-long by .5 meter inner diameter copper pipe weighing…

Q: ater at 60 degrees Fahrenheit is flowing through a smooth horizontal pipe with an internal diameter…

A: Given:Reynolds number=353000diameter=3 inch

Q: Write down the derivation of formulas and describe each variable of "Relative Motion"

Q: In the attached picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed…

A: Solution: Given Data: Sy=500 MPa

Q: A Determine: al The support and joint reactions. b/ The stress resultants in beam BD. F 3L MaFL-

Q: ᴀ ᴅɪᴇꜱᴇʟ ᴇɴɢɪɴᴇ ᴄᴏɴꜱᴜᴍᴇꜱ ꜰᴜᴇʟ ᴀᴛ ᴀ ʀᴀᴛᴇ ᴏꜰ 192 ᴋɢᴍ ᴘᴇʀ ʜᴏᴜʀ ᴀᴛ 28°ᴀᴘɪ. ꜰᴏʀ ᴄᴏɴᴛɪɴᴜᴏᴜꜱ ᴏᴘᴇʀᴀᴛɪᴏɴ,…

A: Fuel rate, m= 192 kg/hr= 192(24) kg/day= 4608 kg/day API= 28∘ Temperature, T= 45∘ To find: Volume,…

Q: Water flows through a pipe at a velocity of 1 m/s. The pipe has a relative roughness of 0.001 and…

A: Given: V= 1m/sRelative roughness εd=0.001diameter d= 100 mmν=10-6 m2/s To find: Point 1 and 2

Q: If the system is released from rest, determine the speeds of both masses after B has moved 1.7 m.…

Q: Develop the shear and bending moment diagrams for the beam 6 kN/m 2.4 kNm B 4 m .6m.

Q: Find the volume of the solid generated by revolving the specified region about the given line R…

Q: 1. A piston-cylinder device contains 10.0 lb,m of water initially at 225 psia and 25.59 ft. Now 4000…

Q: Which of the following working fluids could NOT used in a reverse Brayton cycle operating betwe…

A: Answer is steam.

Q: According to the World Intellectual Property Organization (WIPO), Intellectual property (IP) refers…

A: Despite the fact that construction is a mature industry, it continues to create new equipment,…

Q: At steady state, a device receives a stream of saturated water vapor at 210°C and discharges a…

Q: 6-A heat engine receives 6kW from 250°C source and reject heat at 30°C. Examine each of three cases…

A: Heat input, Qin= 6 kW= 6000 W Source temperature, T1= 250∘C= 250+ 273 K= 523 K Sink temperature, T2=…

Q: 2. Crates A and B weigh 100 lb and 50 lb, respectively. If they start from rest, determine their…

Q: Why are the highest values of Gxy (shear modulus) and Vxy (Poisson ratio) at different angles of…

Q: An aircraft has a total mass of (1.26x10^2) kg and a wing area of (2.3000x10^1) m². It operated with…

A: Chord line is the line joining the leading and tailing edges of the airfoil. Profile line is defined…

Q: ndly show your complete handwritten solution. Answers in m

A: SteelE=200GPa=200000MPaL=3mAluminiumE=70GPa=70000MPaL=2mP=20KNA=500mm2 To-Find:- a) Deformation of…

Q: 09:48 Today Edit 09:44

Q: L12 Find 2/2 and o(42)

Q: two 5 cm diameter, 15 cm long aluminum bars (k=176W/m(degrees Celsius)) with ground surfaces are…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

TORSION

A solid steel shaft 4 feet long is stressed to 18 ksi at 18 Hz when twisted through 3 degrees. Use G = 12 x 10^6 psi.

DETERMINE:

A. Compute the shaft diameter (in inches)

B. the torque applied in the shaft (in lb-ft).

C. What power (in Horseposer) can be transmitted by the shaft?

PROVIDE FBD THANK YOU

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1:

VIEW

Step 2:

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A solid steel shaft 6 m long is stressed at 80 MPa when twisted through 8°. Using G= 83 GPa, compute the shaft diameter. What power can be transmitted by the shaft at 30 Hz?
SOLID STEEL SHAT 5m LONG IS STRESSED AT 80 MPa WHEN TWISTED THROUGH 4º. USING G = 83 GPa, COMPUTE THE SHAFT DIAMETER. WHAT POWER CAN BE TRANSMITTED BY THE SHAFT AT 20 Hz.
A solid shaft 5 m long is stressed to 60 MPa when twisted through 4 deg . Using G = 83 GPa, what power (Hp) can be transmitted by the shaft at 20 rps?
A solid steel shaft of 15m long is stressed at 32 MPa when twisted through 50.Using G =83Gpa .Compute the shaft diameter .What power can be transmitted by the shaft at 40Hz.
A solid steel shaft 5 m. long is stressed to 60 MPa when twisted through 4°. Using G = 83 GPa, compute the shaft diameter. Convert your answers to mm. Based on the problem above, what power can be transmitted by the shaft at 20 r/s? Convert your answer to Mega Watts.
4. Find the diameter of steel line shaft to transmit 10 hp at 150 rpm with a torsional deflection not to exceed 0.08 deg foot length.
Pls answer thank you! Find the diameter of a steel line shaft to transmit 10 horsepower at 150 revolutions per minute with a torsional deflection not exceeding 0.08 degree per foot of length.
A 6m long solid steel pole is emphasized at 80 MPa when twisting through 6 °. Using G = 83 GPa, calculate the diameter of the shaft. What power can the column transmit at 30 Hz
A solid steel shaft is stressed at 100 Mpa when twisted through 6 degrees. Compute the Diameter of the shaft and the Power it transmits at 25 Hz given the following data: Length of shaft = 15 metersG = 83 GPa
A shaft is designed to transmit power of 100 kW at 180 rpm. The allowable shear stress is 50MPa and modulus of rigidity of 80 GPa. The angle of twist is not to exceed to 1° in 4-meter length A. Calculate the diameter of the shaft in inches. B.If the shaft in A is to be fitted to a hub with material SAE 0105 and fit classification of FN3, what will be the maximum and minimum stresses based on the interference of metal.
Shaft length, L and a different allowable maximum shear stress, τmax and subject to a different Torque, T. For steel use a shear modulus, G=81,000 MPa. A steel shaft L meters long is subjected to a torque T. If the shear stress is limited to τmax, calculate: a) The minimum shaft diameter required. b) The angle of twist over the length of the shaft. c) The Power output if your shaft is rotating at 2000 rpm. L= 1.6m, τmax=100MPa , T=1.3kN-m
A hollow steel shaft is transmitting 15 kW at 420 rpm. Calculate the thickness of the shaftwhere outside diameter is 50 mm and allowable shear stress acting in the shaft is 70 MPa