A=A specimen of magnesium having a rectangular cross section of dimension 3.2)mm x 19.1/mm and a gaugelength of 63.5 is pulled in tension. Use the load-clongation characteristics tabulated as follows to:Load0.0 1.38 2.78 5.63 7.43 8.14 9.87 12.85 14.10 14.34 13.83 12.596.99(KN)Al0.0 0.03 0.06 0.12 0.20 0.25 0.641.91 3,18 4.45 5.72(mm)a) Plot the data as engineering stress versus engineering strain.b) Compute the modulus of elasticity.-M. L. 445010c) Determine the tensile strength of this alloy.

Given question: We have to calculate the engineering stress versus engineering strain for the given…

A specimen of magnesium having a rectangular cross section of dimension 3.2)mm x 19.1/mm and a gauge length of 63.5 is pulled in tension. Use the load-elongation characteristics tabulated as follows to: Load 0.0 1.38 2.78 5.63 7.43 8.14 9.87 12.85 14.10 14.34 13.83 12.59 (KN) Al (mm) 0.0 0.03 0.06 0.12 0.20 0.25 0.64 1.91 3,18 4.45 5.72 6.99 a) Plot the data as engineering stress versus engineering strain. b) Compute the modulus of elasticity.Ma L. 495 500 c) Determine the tensile strength of this alloy.

A specimen of magnesium having a rectangular cross section of dimension 3.2)mm x 19.1/mm and a gauge length of 63.5 is pulled in tension. Use the load-elongation characteristics tabulated as follows to: Load 0.0 1.38 2.78 5.63 7.43 8.14 9.87 12.85 14.10 14.34 13.83 12.59 (KN) Al (mm) 0.0 0.03 0.06 0.12 0.20 0.25 0.64 1.91 3,18 4.45 5.72 6.99 a) Plot the data as engineering stress versus engineering strain. b) Compute the modulus of elasticity.Ma L. 495 500 c) Determine the tensile strength of this alloy.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the width and thickness of the leaves (in mm) of a leaf spring using the following specifications: Total load = 140 kN; Number of springs supporting the load = 4; Maximum number of leaves = 10; Span of the spring = 1000 mm; Permissible deflection = 80 mm; Modulus of elasticity, E = 200 kN/mm2; and allowable stress in spring material is 600 MPa.
37) A tensile test specimen has a gage length =3.0 inches and a diameter=0.75 inches. Yielding occurs at a load of 38000 lbs. The corresponding gage length 3.0103 inches (neglect the .2% yield point). The maximum load of 54000lb is reached at gage length 3.453 inches. Determine the modulus of elasticity. (Neglect the .2% offset and round to the nearest whole Msi)
A mild steel bar went through a tensile test conducted at the University of San Carlos Mechanical Engineering Laboratory. The following data was obtained from the test: i. Diameter of the steel bar = 30 mm ii. Gauge length of the bar = 200 mm iii. Load at the elastic limit = 250 kN iv. Extension at a load of 150 kN = 0.21 mm v. Maximum load = 380 kN vi. Total extension = 60 mm vii. Diameter of the rod at the failure = 22.5 mm Determine the Young’s modulus, the stress at the elastic limit, the percentage elongation, and the percentage decrease in area.
A test piece is cut from a brass bar and subjected to a tensile test. With a load of 6.4 kN the test piece, of diameter 11.28 mm, extends by 0.04 mm over a gauge length of 50 mm. Determine: (i) the stress, (ii) the strain, (iii) the modulus of elasticity. (b) A spacer is turned from the same bar. The spacer has a diameter of 28 mm and a length of 250 mm, both measurements being made at 20~ The temperature of the spacer is then increased to 100~ the natural expansion being entirely prevented. Taking the coefficient of linear expansion to be 18 x 10-6/~ determine: (i) the stress in the spacer, (ii) the compressive load on the spacer. rC.G.] [64 MN/m 2, 0.0008, 80 GN/m 2, 115.2 MN/m 2, 71 kN.] Could you please answer thisquestion fully? If you use * could you please explain what you mean by it! Thank You :)
A steel [E = 200 GPa] rod with a circular cross section is 13-m long. Determine the minimum diameter D required if the rod must transmit a tensile force of 23 kN without stretching more than 4 mm. 13.18 mm 28.25 mm 20.13 mm 25.90 mm 21.81 mm
In a tensile test on a specimen of black mild steel of 12 mm diameter, the following results were obtained for a gauge length of 60 mm. Load W(kN) 5 10 15 20 25 30 35 40 Extension x (10-3 mm) 14 27.2 41 54 67.6 81.2 96 112 When tested to destruction. Maximum load = 65 kN; load at fracture = 50 kN, diameter at fracture = 7.5 mm, total extension on gauge length = 17 mm. Find young's modulus, specific modulus, ultimate tensile stress, breaking stress, true stress at fracture, limit of proportionality, percentage elongation, percentage reduction in area. The relative density of the steel is 7.8. Draw the straight line graph.
In a tensile test on a specimen of black mild steel of 12 mm diameter, the following results were obtained for a gauge length of 60 mm. Load W(kN) 5 10 15 20 25 30 35 40 Extension x (10-3 mm) 14 27.2 41 54 67.6 81.2 96 112 When tested to destruction. Maximum load = 65 kN; load at fracture = 50 kN, diameter at fracture = 7.5 mm, total extension on gauge length = 17 mm. Find young's modulus, specific modulus, ultimate tensile stress, breaking stress, true stress at fracture, limit of proportionality, percentage elongation, percentage reduction in area. The relative density of the steel is 7.8. Draw the straight line graph. Answer: breaking stress,true stress at fracture and limit of proportionality.
The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the tube of length L = 10.77 in. Find the maximum safe load P (in lb with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.09 sq, in. area of aluminum = 3.13 sq, in. E of copper = 17082712 ksi E of aluminum = 10068197 ksi allowable stress for copper = 19884 ksi allowable stress for aluminum = 10200 ksi
A tension test was performed on a steel specimen having an original diameter of 12.5 mm and gauge length of 50 mm. The data is listed in the table. Plot the stress–strain diagram and determine approximately the modulus of elasticity, the yield stress, the ultimate stress, and the rupture stress. Use a scale of 25 mm = 140 MPa and 25 mm = 0.05 mm/mm. Redraw the elastic region, using the same stress scale but a strain scale of 25 mm = 0.001 mm/mm.
38) A tensile test specimen has a gauge length =2in. and a diameter= 0.875in. Yielding occurs at a load of 35,500lbs. The corresponding gauge length= 2.0113in (neglect the 0.2% yield point. The maximum load of 45,000lb is reached at a gauge length=2.543in. Determine the modulus of elasticity (neglect the 0.2% offset, and round to the nearest whole Msi)
A bar of 6-mm in diameter is only allowed to decrease at a maximum of 3.96% of its total length. What is the maximum force (Newtons) that can be applied? Consider the shear modulus = 602 MPa, and the Poisson's ratio as 0.20. Express your answer in three decimal places.
The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mmdiameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stressstrain diagram determine the followings properties of the material (Poisson’s ratio of the material is 0.32) : a) Modulus of elasticityb) Yield strengthc) Toughnessd) Resiliencee) Shear modulusf) Bulk modulusg) Ductility as described bypercent change in length