The lap joint shown in the figure below is fastened by six 20-mm diameter rivets. Assuming that p = 50 kN, determine a) the bearing stress in each plate and b) the max. average tensile stress in each plate P P 150 mm ↓ 20 mm ↓ ↑ 20 mm ↑ P P

The lap joint shown in the figure below is fastened by six 20-mm diameter rivets. Assuming that p = 50 kN, determine a) the bearing stress in each plate and b) the max. average tensile stress in each plate P P 150 mm ↓ 20 mm ↓ ↑ 20 mm ↑ P P

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.4P: Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield...

See similar textbooks

Related questions

Q: Train A is traveling at a constant speed VÀ = 34 mi/hr while car B travels in a straight line along…

A: When a body moves on a linear path, then the displacement by the object in a linear direction in a…

Q: Q2/ How will the following increase efficiency of the I.C. engine? 1. Mixing some of exhaust gases…

A: Given questions: 1. Mixing some of exhaust gases with the incoming air 2. Changing air cooling…

Q: P P= 1800 KN allowable shear stress in a bolt=210MPa What is the minimum bolt diameter that may be…

Q: Answer the following question Q4/ A three liters four cylinders C.I. engine has a bore of 9.7 cm and…

Q: e) lost work for non-flow process f) lost work for steady flow process

A: In this problem, it is asking about the answers of parts e and f. so we will answer parts e and f.

Q: Q1. The 93 kg of block C shown in Figure Q1 is being towed with force of P and direction of 45⁰ from…

Q: Q3-A: Determine the x- and y- coordinates of the centroid of the shaded area. | 60 mm 240 mm 120 mm…

Q: Simulate to solve the following ordinary differential equation by using Simulink tool box and…

Q: In the Figure 5, the new length of the cantilever beam due to the inclined force (P) is (in mm):…

Q: An universal coupling is used to connect two mild steel shafts transmitting a torque of 6000 N-m.…

A: Given Torque. T = 6000 N.m Shear stress for the shaft = 55 MPa Shear…

Q: Questions 17-20 According to the truss shown in figure, answer the following questions: 17.The force…

A: Q.18 Given: 3 KN horizontal force at joint H And 4 kN force at joint G and F vertically downward.…

Q: 30 N * "The moment about point A is 35 N 1.5 m B 2m 40% 45° 20 N 2m 80 N.m 58.25 N.M counter…

A: To obtain the moment about point A: MA = ? N. m

Q: ans b please

A: Givenσx=45MPaσy=-60MPaτ=30MPa

Q: 3- In an air standard Brayton cycle, the pressure ratio is 6. The condition of air at the beginning…

A: given; pressure ratio(r)=6 pressure at beginning (P1)=1bar…

Q: The resultant of moments of forces depends on: All the above. O The directions of the applied…

Q: Questions 23, 24 and 25 For the figure shown answer the following: 23. The moment of inertia of the…

Q: What is meant by abnormal combustion in Si engine ? Discuss the various factors which affect…

A: Abnormal combustion: When the combustion gets deviated from the normal behavior resulting in lossof…

Q: In the Figure 3, if m=15 kg and 8=30°, then the weight component of the block parallel to the…

A: Given mass of block = m = 15 Kg Weight of the block W = 15 X 9.81 = 147.15 N

Q: The contractor is instructed to achieve a compacted field dry unit weight of 90% of the maximum dry…

A: Given Maximum density, MDD = 2000 kg/m3 Percentage, x = 90% = 0.9 Find Dry…

Q: j of air in the pipe is limited to 10 m/s and the permissible tensile stress for the material of the…

Q: 1. Fill in the blanks 1) The distribution shape of internal combustion engine can be divided into 2)…

A: Given questions are related to IC engines. [ Note : According to Bartleby's answering guidelines…

Q: driven harmonic oscillator of mass m=0.4 Kg has the equation of motion: 0.4% +0.2x+0.275x= 0.079…

A: Please find the solution below

Q: The 200-mm-diameter gas gun is evacuated on the right of the 8-kg projectile. On the left of the…

Q: 5. Design an oval flanged pipe joint for pipes of internal diameter 50 mm subjected to a fluid…

Q: Design for ", that is, the load can be taken by other members or the effect of fatigue failure…

A: 6) aeroplane 7) high tolerance 8) cause and effect analysis

Q: Liquid water enters a 10-m-long smooth rectangular tube with a 50 mm and b = 25 mm. The surface…

Q: The system in the figure is in equilibrium. A concrete block of mass 215 kg hangs from the end of…

Q: The velocity of A is 3.5 m/s downward, the velocity of B is 4.9 m/s upward, and the velocity of D is…

Q: By using the cosines law, if (a = :40.9 )the force R equals to

A: Given α=40.9o

Q: Q2/ How will the following increase efficiency of the LC. engine? 1. Mixing some of exhaust gases…

A: Given question: How will the following increase efficiency of the IC engine? 1. Mixing some of…

Q: 2. An ideal Diesel cycle receives air at 105 kPa and 315K for isentropic compression. The cycle has…

Q: Design for ", that is, the load can be taken by other members or the effect of fatigue failure…

A: 6) aeroplane 7) high tolerance 8) cause and effect analysis

Q: hornal ab i=k(-200³) 3- If the acceleration of point G is ag = (-261-45.0j) m/s2, determine the…

A: Given Mass, m = 7.5 kg Angular velocity = 18 rad/s Find Force exerted, F

Q: 6. Design for , that is, the load can be taken by other members or the effect of fatigue failure…

A: Solution to first three sub-parts as per our company policy.

Q: The machine element shown is fabricated from steel. The density of steel is 7850 kg/m³. Determine…

A: Given, a=35 mm,b=60 mm,c=20 mm,d=40 mm,e=70 mm,Density of steel, ρ=7850 kg/m2

Q: 2 calculate the ideal cycle efficiency and specific steam consumption (s.s.c.) of a reheat rankine…

A: Given data: Cycle : Reheat Rankine cycleThrottle conditions : 8 MPa and 773 KReheat temperature =…

Q: a=2.1m (1) C = 2m B C b=3.1m d = 1.8m P = 30 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa…

Q: Q4/ A projectile is launched with an initial v, of 75 m/s at an angle of 60° with respect to the…

Q: Shown in the figure is a 258-kg homogeneous cylinder that slipping on the rolls without horizontal…

Q: Water is heated at constant pressure from 5.0 MPa, 140 ºC to 500 ºC. Determine the rate of heat…

Q: Design for that is, the load can be taken by other members or the effect of fatigue failure…

A: 6) aeroplane 7) high tolerance 8) cause and effect analysis

Q: A double window called thermopane is one in which two layers of glass are used separated by a layer…

A: Given Data The change in temperature is: ∆T=27.8 K The thickness of the glass is: xgGlass=6.35 mm…

Q: Consider an air standard otto cycle that has a heat addition of 2800 kJ/kg of air, a compression…

A: Otto cycle is a type of constant volume Heat Addition clockwise cycle consist of 4-reversible…

Q: Water is the working fluid in an ideal Rankine cycle. Superheated vapor enters the turbine at 10…

Q: A WATER TANK IS “L1” IN DIAMETER AND “L2” HIGH. IF THE TANK IS TO BE COMPLETELY FILLED, DETERMINE…

Q: In the Figure 6, the absolute force value in the bar AB is (in kN): Figure 6: y 5 m/ A 20 KN 5 m 5 m…

Q: 1. Assume 1 kg of steam expand isentropically from 2 MPa and 360°C to 0.040 MPa. Find: a) work for…

A: Solution to the first question (a) and (b) parts:

Q: In the Figure 6, the absolute force value in the bar BC is (in kN): Figure 6: 5 m/ y A 20 kN 5 m 5 m…

Q: Q4/ A projectile is launched with an initial v₂ of 75 m/s at an angle of 60° with respect to the…

Q: Box Beam Box Beam Support at A a b с a = 1.7 ft, b = 3.4 ft, and c = 2.55 ft. P = 3300 lb box beam…

Concept explainers

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.

Question

The lap joint shown in the figure below is fastened by six 20- mm diameter rivets. Assuming that p = 50 kN, determine a) the bearing stress in each plate and b) the max. average tensile stress in
each plate
P
P
150 mm
↓
20 mm
000
↓
↑
20 mm
↑
P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680 MPa, and for the bronze (σY)br=490 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm If the yield stress for the steel is (σY)st=610MPa, and for the bronze (σY)br=490MPa(, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa.
The system is initially unstressed but the right support is moved 3 mm to the right whereas the left support remains fixed. Determine the axial stress in bar 1 in MPa. (Numerical absolute answer only without units in 3 decimal places)
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680MPa, and for the bronze (σY)br=490MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa. Express your answer to three significant figures and include appropriate units.
A lever ABC is pinned at C and attached to a 12-mm diameter control cable AD. a. If the allowable tensile stress in the control cable is 140 MPa, what is the maximum safe value of the load P applied as shown in the diagram? b. What is then the shearing stress developed in the 20-mm diameter pin support at C? c. What is the bearing stress between the pin and the 25-mm thick support plates at C?
A-36 Aluminium rod shown in figure Q1a is 2.5 m long and must not stretch more than 1.5 mm when an 10.5 kN load is applied to it. Knowing that E = 75 GPa, determine (i) the smallest diameter rod which should be used, (ii) the corresponding normal stress caused by the load.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Draw appropriate FBDs showing how the internal forces were determined. A square bar (side length = 50 mm) is welded to a fixed supporting slab. A 30-mm diameter pin is inserted in the bar. When the loading shown is applied, determine the following: a. maximum normal stress in the bar (MPa) and bearing stress between the pin and the bar (MPa)b. stress in the weld between the bar and the supporting slab (MPa)c. shear stress in the pin (MPa) and shear stress in the bar (MPa)
The assembly shown below consists of a brass shell (1) fully bonded to a ceramic core (2). The brass shell [E = 115 GPa; α = 18.7 x 10-6 /°C] has an outside diameter of 50 mm and an inside diameter of 35 mm. The ceramic core [E = 290 GPa; α = 3.1 x 10-6 /°C] has a diameter of 35 mm. At a temperature of 15°C, the assembly is unstressed. Determine the largest temperature increase that is acceptable for the assembly if the normal stress in the longitudinal direction of the brass shell must not exceed 80 MPa.
Determine the safe wall thickness of a 50 inches steel tank with internal pressure of 8 Mpa. The ultimate stress is 296 Mpa. The factor of safety to use is 3. A. 2 in B. 3 in C. 5 in D. 4 in
@2 The support consists of solid brass post surrounded by a steel tube. Before the load is applied, the gap between these two parts is | mm. Given the dimensions shown in the figure, determine the greatest axial load that can be applied 0 the rigid cap A if the maximum allowable stress in brass is (Guiin)se = 150 MPa and the maximum allowable stress in steel is (Gun ) = 200 MPa. E, = 200 GPa and Ey,= 100GPa.
A crane hook shown in figure below is made of 30 mm diameter steel rod. The distance between the centroidal axis of the rod and centre of curvature of the hook is 50 mm. Determine the load 'F' so that the maximum stress in the rod is not to exceed 40 N/mm². Proper Answer plz.