A steel bar has a length of 2.5 m and cross-section of 200-mm x 100-mm. The modulus of elasticity of this material is 210 GPa and Poison's Ratio is 0.3. The change in width after applying a tensile force of 150 kN is?

A steel bar has a length of 2.5 m and cross-section of 200-mm x 100-mm. The modulus of elasticity of this material is 210 GPa and Poison's Ratio is 0.3. The change in width after applying a tensile force of 150 kN is?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 20CQ

See similar textbooks

Related questions

Q: Which step of the process should an error be found—the construction stage or the run stage

A: Ideally, errors should be caught and corrected as early in the process as possible to minimize their…

Q: A solid steel shaft is to transmit a torque of 10 kN- m. If the shearing stress is not exceed 45…

A: Given data: Transmitted torque, T = 10 kN-m Maximum allowable shear stress, τmax=45 MPa

Q: Example 3: A flow net for flow around a single row of sheet piles in a permeable soil layer is shown…

A: given data K=5×10-3cm/secfrom images of question total head loss=5.6-2.2=3.4mno of drops Nd=6no of…

Q: Problem 5.12 A stream function is given by y Calculate the velocity components and also magnitude…

A: The given stream function is,

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: Following are the given information. Segment 1 =Brass Segment 2 =Aluminum Allowable shear stress of…

Q: a) Find the steel pipe diameter required to convey a maximum of 500 lit/sec of water. The pipe…

A: Given data: Required discharge: Q=500 lit/sec = 0.5 m3/s Pipe length: L= 5km = 5000 m Head…

Q: Volumetric Strain Question 5: The principal stresses at a point in an elastic material are 60 N/mm²…

A: Given- Stresses- σx=60 N/mm2σy=20 N/mm2σz=-50 N/mm2E=100×103 N/mm2μ=0.3 Volumetric strain=?

Q: Given the grid below, perform the eartwork calculations, utilizing the cell method. The dimesions of…

A: The cell has dimensions of 50x50 Existing spot elevation and proposed spot elevation data for…

Q: Determine the required magnitude of force P to maintain equilibrium of the linkage at 0 = 60°. Each…

A: Draw FBD:

Q: Es 3.2m 24 KN PROBLEM 6.6 Using the method of joints, determine the force in each member of the…

A: Objective: To determine the force in each member of the given truss, using the method of joints.…

Q: Problem #3. Compute and plot all moments and sheers. Compute all reactions

A: According to Q&A guidelines, only the first question (Problem#3) will be answered as it is a…

Q: Question- The capillary rise of water is 3cm in a tube. Find the diameter (mm) of tube if surface…

A: Capillary rise h=3 cm=0.03 m, Surface tension s=0.075 N/m, Diameter of the tube = ?

Q: The cable shown in the figure, supports a girder which weighs 40 kN/m. Determine the tension in the…

Q: 2. 50 kips 6 ft B 560 kip-ft 10 ft 6 ft 20 kips/ft 12 ft 6 ft

A: A loaded beam is given as shown and it has been asked to draw shear force and bending moment…

Q: ▼ Part A Determine the axial forces in members BC, CD, and CE of the truss. (Figure 1) Enter your…

Q: Problem 2 An earth dam is built on an impervious foundation with a horizontal filter at the base…

A: Given that:- An earth dam is built on an impervious foundation KH= 3×10^-² mm/sec = 3× 10^-5m/sec…

Q: Tutorial 3 (Analysis of Frames) Find the support reactions, and draw the axial force diagram, shear…

A: Given Data Determine the support reaction and draw axial force diagram, shear force diagram and…

Q: A uniform density sheet of metal is cut into the shape of an isosceles triangle, which is oriented…

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The BEPZA authority decides to conduct a field compaction test by their own facilities. They already…

A: Compaction is a mechanical procedure that increases soil density while also removing air. There is…

Q: Find the shape factor for the tee section as shown in figure. 20 mm 20 mm -120 mm 200 mm

A: Find the shape factor.

Q: A cantilever beam AB as shown in figure is subjected to a point load of 12 kN over a span of 6 m…

A: Given: A cantilever beam AB as shown in figure, Point load, P = 12 kN Span length of beam, l = 6 m…

Q: A = Roll 16 kN/m' 6 m 4 6m + M = 96 kNm 4 m B = Pin

Q: Explain metrology science and what it comprises, as well as the skills and training required to…

A: Metrology is the scientific study of measurement, which involves the development, implementation,…

Q: A small sphere of diameter D and density p, is dropped into a large body of fluid of density p.…

Q: On a B. G track 3° curve, the equilibrium cant is provided for a speed of 70 kmph. (i) Calculate the…

Q: Draw the shear and moment diagram

Q: Determine the volume of excavation works required, assuming that Erika does not allow a quantity…

A: Given Equilateral Traingle : Volume = Area * Length = 1/2 * 6* 4*4 = 48 yd^2

Q: Question #15, Case 5: Highway accident A flagger was killed on a highway construction project when a…

A: In this scenario, the deceased woman's family's insurance company can sue the driver, the…

Q: Compute and plot all moments and sheers Compute all veactions

A: According to Q&A guidelines, only the first question (Problem#3) will be answered as it is a…

Q: Given the figure and the following data: Determine (a) the width of base b on the conditions: a.1…

A: Given The unit weight of the concrete = 2.4 T/m3 The coefficient of friction between the base and…

Q: At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is…

A: Initial temperature (Ti) = 60°F Bar-1: Width of bar1 = 3 in. Thickness of bar1 = 0.75 in. L1 = 32…

Q: 4. For the compound beam and loads as shown, find (a) the maximum reaction at C (b) the maximum…

A: I have solved this problem in detail although I have used it by logic and by self inspection which…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm and a…

Q: The water table at a location is at the ground surface and the saturated unit weight of the soil is…

Q: 3 Draw the influence line for the force in (a) member JI, (b) member IE, and (c) member EF. L Lapo B…

A: Influence line Diagram are used to show the response of each section at any distance across any…

Q: Water is flowing at a critical depth of flow = 1.4 m in a channel shown in the figure below.…

A: Critical Depth (Yc) = 1.4 m Discharge (Q) and Specific energy (E) in the channel = ?

Q: Problem A bridge girder consists of W 760 x 161 and a channel C 380 x 50.4 and joined by 2 - 22 mm Ø…

A: Maximum bending stress in tension is the maximum stress in the beam due to the bending moment .…

Q: The magnitude of the reaction exerted on the L-shaped bar at B is 70 lb. (Figure 1) Figure 17 in 14…

Q: Differential leveling between BMS A, B, C, D, and A gives elevation differences (in meters) of…

A: We know that Adjusted elevation is given by Initial elevation + Correction Adjusted elevation =…

Q: A combined footing is proposed to support two columns, C1 and C2, with loads equal to 2000 kN and…

A: (i) Soil Bearing Capacity: The bearing capacity of the soil can be calculated using the following…

Q: The spool shown in (Figure 1) has a mass of 100 kg and radius of gyration about its mass center of…

A: Following are the given information. Mass of spool, m=100 kg The radius of gyration about its mass…

Q: The duty of a crop is 432 hectares per cumec and the base period of the crop is 100 days. The delta…

A: Given- The base period of the crop, B = 100 days Duty of crop, D = 432 hectares/cumec The delta of…

Q: 1) Calculate the exceedance probability, p and recurrence interval, Tp (years of the observed data…

A: Given:- The maximum rainfall and runoff of a catchment for 21 years To determine:- 1) The…

Q: 4-4 An engineer wishing to obtain the speed characteristics on a bypass around her city at a…

A: Given- An acceptable limit = ±1 mi/h The total spot speed sample = 130 The variance = 25 (mi/h)2…

Q: When subjected to a torque, a circular shaft undergoes a twist of 1° in a length of 1200 mm, and the…

A: Given that :- Length = L = 1200 mm maximum shear stress = τmax=80 N/mm2 Modulus of rigidity = G =…

Q: A 3.2 meter thick silty sand stratum intersects one side of a reservoir. The stratum has a hydraulic…

Q: Determine the volume of 50-mm plain concrete bedding.

A: Following are the given information. Thickness of plain concrete bedding =50 mm=0.050 m Length of…

Q: 4-5 An engineer wishing to determine whether there is a statistically significant difference between…

A: Given data- To Find- Whether the average speed of large trucks and passenger cars be same?

Q: he platform scale consists of a combination of third and rst class levers so that the load on one…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduce the problem statement

VIEW

Step 2: Determine longitudinal strain

VIEW

Step 3: Determine lateral strain

VIEW

Step 4: Determine the change in width

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
The frame of a space shuttle type vehicle must have a high yield strength and high stillness, and the most important design factor is weight. Of all the materials presented in this chapter, what material might be the most suitable for the frame of a space shuttle? Assume that there will be both tensile and compressive stresses. For a space shuttle, cost is not a limiting factor. (a) You can eliminate entire classes of materials from consideration with a brief statement about their unsuitability. (b) What material has the highest specific yield strength? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (c) What material has the highest specific elastic modulus? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (d) Compare the materials with the highest specific yield strength and highest specific elastic modulus for suitability in the space shuttle frame. (C) Discuss the suitability of the top-rated material for this design from the viewpoint of the ability to produce a frame.