Answered: A steel boiler 2.5 m in diameter has a…

A steel boiler 2.5 m in diameter has a wall thickness of 25 mm. The internal pressure is 1.6 MPa. Calculate the factor of safety if the maximum permissible stress for it is 250 MPa?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Related questions

Q: PROBLEM: 1 A pair of wheels of a railway wagon carries a load of 50 kN on each axle box, acting at a…

Q: A thin cylindrical pipe with an inside diameter of 300 mm is 6 mm thick and fitted with end covers.…

Q: Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane…

A: Given details:Es=205GPaEc=100GPadiameter of rod = 20mm

Q: A steam boiler is to have a 300-mm-diameter hand hole placed on one end. If the maximum internal…

Q: A square tie bar 20 mm x 20 mm in section carries a load. It is attached to a bracket by means of 6…

Q: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected…

Q: The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of…

A: Given Data The diameter of pin is:d=24mm=24×10-3 m The width of the rectangular bar is:b=70…

Q: For a closed end cylinder where the inner radius is 20 mm and outer radius is 40 mm, and the…

A: Sddd

Q: Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by…

Q: Q3. For a closed end cylinder where the inner radius is 20 mm and outer radius is 40 mm, and the…

A: given data inner radius = 20 mm outer radius = 40 mm internal pressure = 5 Mpa

Q: Example: The coupling shown in Fig. below is constructed from steel of rectangular cross-section and…

A: For the given coupling P = 50 kN dia of bolt (d) = 15 mm To determine (i) the shear stress in…

Q: Q2. Two 35 mm shafts are connected by a flanged coupling The flanges are fitted with 6 bolts on 125…

Q: 4. A ring made of 2-5 cm diameter steel bar carries a pull of 10 kN. Calculate the maximum tensile…

A: Given: The diameter of ring, d = 2.5 cm 0.025 m The load, P = 10 kN The mean radius, R = 15 cm =…

Q: Design a knuckle joint to two connect two co-axial steel rods with 45C8 (S= 380 N/mm) to support a…

A: given data

Q: 13.9 (8) A thick cylinder has an internal diameter of 75 mm and an external diameter of 125 mm. The…

Q: An axially loaded bar has normal stress 173 MPa. The shear stress in the bar is

A: given data : Maximum principal stress (σ1)=173 MPaMinimum principal stress (σ2)=0

Q: A steel pipe 1.5m in diameter is required to carry an internal pressure of 650kPa. If the allowable…

Q: The shaft of a hand operated wire rope hoist is supported on bearings A and B. The shaft is keyed to…

Q: 1. Problem 1: Segment AB of the bar is a hollow tube with an outer diameter of 1.5 inches and a wall…

Q: 1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa,…

A: GivenP=15000NLi=40mmLo=L=?σallow=75MPa=75 N/mm2

Q: . Find the thickness of the flat end cover plates for a 1 N/mm2 boiler that has a diameter of 600…

Q: hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine…

A: Given, the tensile load, P=400kN=400000N Stress, σ=120MPa Area, A=14πD2-14π1002=14πD2-10000

Q: Jason took a steel rod, 15.29-mm in diameter, and held snugly (but without any initial stress)…

A: Given: The diameter of rod, D = 15.29 mm The coefficient of thermal expansion, α = 13.6x10-6 mm/mmoC…

Q: What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of…

Q: PROBLEM 6/6 F = 520 kN Determine the stress in each aluminum and steel bars after 0.2 mm F = 520 kN…

Q: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected…

A: Given:Pressure, P=7.875 MPadiameter, d=400 mmthickness, t=20 mm

Q: |P2=20kN 0.5 m A P1=100kN 40 mm 40 mm 25mm 25mm

A: Area of cross-section,A=50*80A=4000 mm2Moment of inertia about normal axis,Ix=50*80312 Ix=2133333.33…

Q: A cylindrical pressure vessel has an internal diameter of 2 m and is fabricated from plates 20 mm…

Q: A rubber block with dimensions 120x120x120 mm is a rigid mold It is compressed with a vertical force…

Q: 41.) A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is…

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

A: Given A steel bolt Tensile load P=40kNMajor diameter(d1)=6 mmMinor diameter d2=4 mmAverage tensile…

Q: 3.9 A thin cylindrical steel drum, 10 mm thick, is subjected to an internal pressure of 1,5 MPa and…

A: Given data: N=259 rpmσ=120 MPa Need to determine the diameter of the drum.

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

A: The formula for the hoop stress can be expressed as,

Q: A scuba tank is being designed for an internal pressure of 2,685 psi with a factor of safety of 2.0…

Q: The wall thickness of a spherical thank is 8mm, calculate the diameter if allowable stress is 140MPa…

Q: The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of…

Q: A cylindrical pressure vessel is fabricated from steel plating that has wall a thickness of 10 mm…

Q: Figure Q5 shows a thick cylinder of [A] mm intemal radius and [B] mm outer radius is subjected to an…

A: Given data: Inner Radius = A Outer Radius = B Internal Pressure = 60 MN/m2 External Pressure = 30…

Q: A 30 mm square is drawn on the rim of a large steel pressure vessel. The biaxial stress situation in…

Q: how many 15 mm holes will be required to keep the cover plate in position?

A: GIven: Internal pressure=1.3 MPA Diameter of the plate=300 mm diameter of bolt=12 mm Allowable…

Q: 1. Can you treat this cylinder as Thin-Walled Cylinder? Prove that? 2. Calculate the tangential and…

A: Stress: Stress is nothing but force per unit area. It is represented by σ & the SI unit of…

Q: a) A steam engine cylinder has an effective diameter of 350 mm and the maximum steam pressure acting…

A: solving the part (a)

Q: A mild steel tie-rod has to carry an axial load of 60KN. The maximum permissible stress is 200N/mm2.…

Q: For the figure shown, if the tensile force in member AB is 38 kN and the ........ allowable stress…

A: Given:TAB=38 KNσallow=120 MPa

Q: 1.7 The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given, Diameter of wooden post = d = 8 in Length of square concrete footing = L = 12 in Working…

Q: 1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20…

A: as per guideline i have to solve only first question

Q: A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is…

Q: For the pin connection shown, determine the normal stress acting on the gross area, the normal…

A: Given data Given force system

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

. A steel boiler 2.5 m in diameter has a wall thickness of 25 mm. The internal pressure is 1.6 MPa. Calculate the factor of safety if the maximum permissible stress for it is 250 MPa?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of 18 MPa? Use a design stress of 80 MPa?
Q // If the value of the highest load we get from the tensile test of a wrought iron model with a circular . section is (52 kN) with an axial stress of ( 460 Mpa), calculate the diameter of the examined model
A hollow cylinder of external diameter 50 mm and internal diameter 30 mm is subjected to tensile load of 150 kN. Then the tensile stress is _____________ MPa
A tube from aluminium with an outside diameter of 50 (mm) and a wall thickness of 5 (mm) is used as a compression member. If the axial normal stress in the member must be limited to 90 MPa, what is the maximum force (in kN) that the member can support.
What will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the stress in the rod is not to exceed 95 MN/m²?
A cylindrical pressure vessel with a diameter of 600 mm is to be fabricated from steel plates of thickness 16 mm. Compute the maximum value of the internal pressure it can hold inside if the tangential stress is limited to 140 MPa with a safety factor of 2.4. a. 4.28 MPa b. 5.28 MPa c. 3.11 MPa d. 6.09 MPa
A thin cylindrical pressure vessel with closed-ends is subjected to internal pressure. The ratio of circumferential (hoop) stress to the longitudinal stress is?