Answered: An axially loaded bar has normal stress…

Engineering

Mechanical Engineering

An axially loaded bar has normal stress 173 MPa. The shear stress in the bar is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Related questions

Q: A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detennine…

A: Given The outside diameter of hollow steel tube is D=138 mm. The inside diameter of tube is d=120…

Q: Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in…

A: Given: Diameter of the rod D=50mm Diameter of the pin Dp=40mm Tensile force F=120kN

Q: ort square is 1 1/2 inches x 1 1/2 inches in cross section. it is on an axial tensile load of 11,000…

Q: Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane…

A: Given details:Es=205GPaEc=100GPadiameter of rod = 20mm

Q: 1.) A long flat steel bar 6 in. wide and 3/8 in. thick has a 2.5 in. diameter circular hole…

Q: . A hydraulic press exerts a total load of 3.5 MN. This load is carried by two steel rods,…

Q: А cube with an edge of 2·5 cm as shown in Fig. 1.4 was tested in compression. Under a load of 400 kN…

A: In compression, we examined a cube with a 2.5 cm edge, as illustrated in the picture. It failed…

Q: A hollow cylinder of external diameter 50 mm and internal diameter 30 mm is subjected to tensile…

Q: e state of stress at a point in a circular bar under pure torsion is given by T xy = T yx= t and…

Q: A wooden bar is subjected to a tensile stress of 5 MPa. What will be the values of normal and shear…

A: Given data: The tensile stress in wooden bar is σ = 5 MPa. The angle between the section and the…

Q: 8. A solid steel bar of diameter d, = M mm has a hole of diameter d2 = N mm drilled through it. A…

Q: A compression load of P= 50 kips is applied to a 2 in. by 2 in. square post, as shown. Determine the…

Q: 1. Determine the maximum safe load P which may be applied if the shearing stress in the rivets is…

Q: 2. A prismatic bar under an axial load produces a tensile stress of 75MPa on a plane at an angle of…

A: Calculated normal and shearing stress in all faces of the element at an angle of 50 degrees.

Q: A body is subjected to a direct tensile stress of 300 MPa in one plane accompanied by a simple shear…

A: given data tensile stress = 300 MPa simple shear = 200 MPa to determine maximum shear stress

Q: 1:in the following arrangement of structur allowable shear stress in pin C is 16 Mpa calculate the…

A: Given;- W=36N/m D=10mm Shear stress=16Mpa

Q: Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

Q: 1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa,…

A: GivenP=15000NLi=40mmLo=L=?σallow=75MPa=75 N/mm2

Q: Two square bars (15mm thick) are bolted together as shown. Volt's allowable shear stress is 90 MPa,…

Q: The stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.

Q: The formula for Critically Resolved Shear Stress is

Q: If the cross sectional area of bar BD is 0.5 in2, what is the stress in bar BD?

Q: What is the minimum diameter of a bar subjected to an axial load of 6.5 kN if its ultimate stress is…

Q: The compound steel bar shown in Fig. Q1(b) made of three uniform segments marked as 1, 2 and 3 of…

Q: A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear…

A: Given data Direct tensile stress = 300 MPa Shear stress = 200 Mpa

Q: a cylindrical disk with diameter 40 mm and thickness 2 mm is compressed stress = applied…

A: As this is a simple question related to the strength of material subject. As stress formula is given…

Q: The lap joint shown if Fig. is fastened by four 3/4 inch diameter rivets. Calculate the maximum safe…

Q: Rod (2) Rod (1)

A: Given that, Diameter of the circular rod, D=50 mm,Diameter of the pin, d=40 mm,Tensile force applied…

Q: A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of 40 kN.…

A: GivenD=25 mm=0.025md=12 mm=0.012mF=40 kN=40×103 Nσmax=225 MN/m2=225 ×106 N/mAskedσ=?Fmax=?

Q: Calculate the increase in stress for each segment of the compound bar shown. If the temperature…

A: Solution: Given Data: Aal=3 in2Eal=107 psiαal=12.8×10-6/oFAs=1.5 in2Es=29×106…

Q: A cylindrical pressure vessel is designed using steel plating with a thickness equivalent to 15 mm.…

A: Write the given data. t=15 mmD=460 mmH=2.5 mσL=120 MPaσc=50 MPa

Q: Q.1. A. For a hellow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A: 1) Given: Outside diameter D2=138mm Inside diameter D1=120mm Maximum tensile stress=115MN/m2 or…

Q: A circular rod is stretched by a force of 3kN. Solve the diameter of the rod if the stress is not to…

A: Force on rod,P=3KN=3×103NMaximum stress,σ=153MPa=153×106PaLet the diametre of rod=d

Q: The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of…

Q: A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the…

Q: and (b) the ratio o 3.51 Fig. shows a circular steel bar. (a) and Fig. square st T applied to them.…

A: Given:r=aπ

Q: 3. A circular steel bar is subjected to an axial compressive load of 175 kN. The bar has a diameter…

Q: A rectangular 30 mm x 25mm bar of length 250 mm subjected to axial tension load of 75 kN. Determine…

A: As per our guidelines we have to answer only one question. So, post the question seperately and…

Q: Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh If the…

Q: A 1.25 in.-square steel punch is to push through an aluminum plate that is supported on a die, thus…

A: Given The side of the square steel punched part is s=1.25 in. The allowable compressive strength is…

Q: 2.49. A bar of rectangular cross section 20 mm × 3 mm has a central hole of diameter 6 mm. Find the…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: QUESTION 3 Calculate for E=200 GPa: 3.1 The diameter 'd' if the stress is not to exceed 142 MPa 3.2…

A: As per given question we determine the value of D and x

Q: An axial bar fixed at both ends with no loads applied is subjected to an increase of temperature.…

Q: For the figure shown, if the tensile force in member AB is 38 kN and the ........ allowable stress…

A: Given:TAB=38 KNσallow=120 MPa

Q: A wooden bar is subjected to a tensile stress of 5 mpa. What will be the values of normal stress and…

A: Given data The tensile stress σ = 5 MPa. angle between the section and the tensile stress is θ =…

Q: A rod is hanging vertically, supports a load of 2000N. Neglecting the weight of the wire, determine…

A: Given data, P= 2000 N Tensile stress = σ= 140 MPa, N/mm2

Q: For 13 to 15. The compound bar carries the axial forces P and 2P. The working stresses are 40 ksi…

A: (13) To find: The maximum allowable value for P. Given: The length of aluminum bar is LAl=3 ft. The…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

An axially loaded bar has normal stress 173
MPa. The shear stress in the bar is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A wooden bar is subjected to a tensile stress of 5 mpa. What will be the values of normal stress and shear stress across a section, which makes an angle at 250 with the direction at the tensile stress
A hollow cylinder of external diameter 50 mm and internal diameter 30 mm is subjected to tensile load of 150 kN. Then the tensile stress is _____________ MPa