A steel pipe with 5-cm OD is covered with a 6.4-mm asbestos insulation [k =0.096 Btu/h ft. °F] followed by a 2.5-cm layer of fiberglass insulation [k =0.028 Btu/h ft. °F]. The pipe-wall temperature is 315°C, and the outside insu- lation temperature is 38°C. Calculate the interface temperature between the asbestos and fiberglass. %3D W

A steel pipe with 5-cm OD is covered with a 6.4-mm asbestos insulation [k =0.096 Btu/h ft. °F] followed by a 2.5-cm layer of fiberglass insulation [k =0.028 Btu/h ft. °F]. The pipe-wall temperature is 315°C, and the outside insu- lation temperature is 38°C. Calculate the interface temperature between the asbestos and fiberglass. %3D W

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.77P: 1.77 Explain each in your own words. (a) What is the mode of heat transfer through a large steel...

See similar textbooks

Similar questions

What is the rate of heat transfer, temperature gradient, and the direction of the heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? - thermal conductivity of Celotex in AES = 0.028.
1. Most bridges contain interlocking steel grates (α steel = 1.2 x 10 - 5 ºC -1 ) that allow the bridge toexpand and contract with the changes in temperature. The Golden Gate Bridge in San Francisco isabout 1350 meters long.(A) The seasonal temperature variation in San Francisco ranges from about 0ºC to 30ºC. Howmuch will the bridge expand between these two extremes?(B) What percent of the length of a subcompact automobile, 2.5 meters, does this gaprepresent?2. Selena has a fire in her fireplace to warm her 20ºC apartment. She realizes that she hasaccidentally left the iron poker (α iron = 1.2 x 10 -5 ºC -1 ) in the fire. How hot is the fire if the 0.60-meter poker lengthens 0.30 cm?3. Just before midnight, when the air temperature of 10.0ºC, Karl stops and fills the 0.0600 m 3 gastank in his car. At noon the next day, when the temperature has risen to 32ºC, Karl finds a puddle ofgasoline (βgas = 3 x 10 -4 ºC -1 ) beneath his car.(A) How much gasoline spilled out of Karl's car?…
What is the rate of heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? thermal conductivity of Celotex in AES = 0.028. Pls determine the temperature gradient and the direction of the heat transfer as well.
3.6 Heat losses through windows in buildings are substantial. What would be the percentage reduction in heat loss that would be mitigated by replacing a window containing a single pane of glass with (a) double-pane low-E insulating glass or (b) a 3-inch-thick sheet of expanded polystyrene sheet? The quoted R values for these items are: • single pane of glass: 0.90 ft 2 hr ° F/Btu, • double pane of low-E insulating glass: 2.3 ft 2 hr ° F/Btu, • 1-inch-thick sheet of polystyrene sheet: 4.0 ft 2 hr ° F/Btu.
Q2: A: The exterior wall of a single-story office building near Chicago is 3 m high and 15 m long. The wall consists of 100-mm face brick, 40-mm polystyrene insulating board. 150-mm lightweight concrete block, and an interior 16-mm gypsum. The wall contains three single-glass of 3 mm thickness windows 1.5 m high by 2 m long. Calculate the heat loss through the wall at design conditions if the inside temperature is (20 °C). The outside temperature is (-18 "C).
Consider the vertical heat sink (see the figure) used to cool a surface at 70 0C. The room temperature is 30 0C. The dimensions are given as (H=2 cm, L=5 cm, t=1 mm, W=15 cm). If the space between the fins is arranged so that the heat transfer rate is maximum, what is the heat transfer rate from the heat sink? Properties of air: ρ=1 kg/m3, k=0.03 W/mK, ν=1.5x10-5 m2/s, cp=1 kJ/kg0C, Pr=0.7
Hi, can you help me with the following problem? A thermally insulated tank of water 2 m x 2 m, depth 1 m is stirred with a paddle for threehours. If the paddle is driven by a motor whose shaft power is 8 kW determine the rate ofchange of temperature in degrees C per hr and the increase in temperature of the water.The specific heat of water is 4200 J/kgC. Identify a system and start your analysis from anappropriate form of the Fist Law of Thermodynamics
Steel pipe 1 cm thick, 1.0 m long and 8 cm deep, covered with 4 cm thick insulation. The wall temperature in the steel pipe is 100 ° C. The ambient temperature around the insulated pipe is 24 ° C. The convection heat transfer coefficient outside the insulation surface is 50 W / (m² K). The thermal conductivity of steel is 54 W / (m K), and the thermal conductivity of the insulation is 0.04 W / (m K). Count; a. Heat loss per meter of pipe = watt. b. Temperature between steel pipe and insulation. = ° C
Steel pipe 5 cm thick, 1.0 m long and 12 cm deep, covered with 8 cm thick insulation. The wall temperature in the steel pipe is 100 ° C. The ambient temperature around the insulated pipe is 24 ° C. The convection heat transfer coefficient outside the insulation surface is 50 W / (m² K). The thermal conductivity of steel is 54 W / (m K), and the thermal conductivity of the insulation is 0.04 W / (m K). Count; a. Heat loss per meter of pipe ... (watts)b. temperature between steel pipe and insulation ... (° C)
As a designer working for a major electric appliance manufacturer, you are required to estimate the amount of fiberglass insulation packing (k = 0.035 W/m K) that is needed for a kitchen oven shown in the figure below. The fiberglass layer is to be sandwiched between a 2-mm-thick aluminum cladding plate on the outside and a 5-mm-thick stainless steel plate on the inside that forms the core of the oven. The insulation thickness is such that the outside cladding temperature does not exceed 40C when the temperature at the inside surface of the oven is 300C. Also, the air temperature in the kitchen varies from 15Cto33C, and the average heat transfer coefficient between the outer surface of the oven and air is estimated to be 12.0W/m2K. Determine the thickness of the fiberglass insulation that is required for these conditions. What would be the outer surface temperature when the inside surface of the oven is at 475C?
1.77 Explain each in your own words. (a) What is the mode of heat transfer through a large steel plate that has its surfaces at specified temperatures? (b) What are the modes when the temperature on one surface of the steel plate is not specified, but the surface is exposed to a fluid at a specified temperature?
1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.