The cake mix, whose initial temperature is 25°C, will be baked at 120°C in a cylindrical mold. It takes 802 h for the core temperature of the cake to reach 98°C and this time is considered sufficient for baking the cake. Calculate the diameter of the mold in which the cake should be placed. h=68.6 W/m?K, d=840 kg/m³ cp=3400 J/kgK, k=1.2 W/mK, A=3.07

The cake mix, whose initial temperature is 25°C, will be baked at 120°C in a cylindrical mold. It takes 802 h for the core temperature of the cake to reach 98°C and this time is considered sufficient for baking the cake. Calculate the diameter of the mold in which the cake should be placed. h=68.6 W/m?K, d=840 kg/m³ cp=3400 J/kgK, k=1.2 W/mK, A=3.07

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.16P

See similar textbooks

Similar questions

Partially-frozen ice cream is being placed in a package before completion of the freezing process. The package has dimensions of 8 cm by 10 cm by 20 cm and is placed in air- blast freezing with convective heat coefficient of 50 W/(m2 K) for freezing. The product temperature is -5°C when placed in the package, and the air temperature is -25°C. The product density is 700 kg/m3, the thermal conductivity (frozen) is 1.2 W/(m K), and the specific heat of the frozen product is 1.9 kJ/(kg K). If the latent heat to be removed during blast freezing is 100 kJ/kg, estimate the freezing time.
A long steel rod 0.305 m in diameter is initially at a temperature of 588 K. It is immersed in an oil bath maintained at 311 K. The surface convective coefficient is 125 W/m2 -K. Calculate the temperature at the center of the rod after 1 h. The average physical properties of the steel are k = 38 W/m-K and α = 0.0381 m2/h.
During a cold winter day, wind at 55 km/h is blowing parallel to a 4m high and 10m long wall of a house. If the air outside is at 5 degrees Celsius and the surface temperature of the wall is 12 degrees Celsius , determine the rate of heat loss from the wall by convection. What would your answer be if the wind velocity has doubled? From Table A-1:thermal conductivity, k = 0.0246 W/m degrees Celsiusviscosity, v = 1.4 x 10^-5 m^2/sPrandtl no. Pr = 0.717
A long 8-cm-diameter steam pipe whose external surface temperature is 90°C passes through some open area that is not protected against the winds. Determine the rate of heat loss from the pipe per unit of its length when the air is at 1 atm pressure and 7°C and the wind is blowing across the pipe at a velocity of 50 km/h.
. Castor oil at 36 °C flows over a 6 m long and 1 m wide heated plate at 0.06 m/s. For a surfacetemperature of 96 °C, determine (i) the thermal boundary layer thickness at the end of the plate,(ii) the local heat transfer coefficient at the end of the plate, and (iii) the rate of heat transfer fromthe entire plate
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
air at a dry ball temperature of 80 degrees C and 4% RH is passed over the cooling coil so that the temperature of the air dry ball becomes 35 degrees Celsius. how much heat is released from the air in the process? (answer in kj / kg)
The author and his then 6-year-old son have conducted the following experiment to determine the thermal conductivity of a hot dog. They first boiled water in a large pan and measured the temperature of the boiling water to be 94°C, which is not surprising, since they live at an elevation of about 1650 m in Reno, Nevada. They then took a hot dog that is 12.5 cm long and 2.2 cm in diameter and inserted a thermocouple into the midpoint of the hot dog and another thermocouple just under the skin. They waited until both thermocouples read 20°C, which is the ambient temperature. They then dropped the hot dog into boiling water and observed the changes in both temperatures. Exactly 2 min after the hot dog was dropped into the boiling water, they recorded the center and the surface temperatures to be 59°C and 88°C, respectively. The density of the hot dog can be taken to be 980 kg/m3, which is slightly less than the density of water, since the hot dog was observed to be floating in water while…
Ethylene glycol at 40°C flows over a heated plate very wide, 6 m long, at velocity of 0.04 m/s. For a temperature = 90°C, determine: 1- the thickness of the hydrodynamic boundary layer at the end of the plate2- the thickness of the thermal boundary layer at the end of the plate3- the local and average heat transfer coefficient at the end of the plate4- the total heat flux transferred from the heated surface.
A fabricated food, in the form of small spherical pellets, is to be frozen in an air-blast freezer. The air-blast freezer isoperating with air at -40°C. The initial product temperatureis 25°C. The pellets have a diameter of 0.5 cm, and the density of the product is 980 kg/m3. The initial freezing temperature is -2.5°C. The latent heat of fusion for this product is 280 kJ/kg. The thermal conductivity of the frozen productis 1.9 W/(m°C). The convective heat transfer coefficient is 50 W/(m2 °C). Calculate the freezing time.
A 5.0-cm-diameter cylinder is heated to a temperature of 200°C, and air at 30 °C forced across it at a velocity of 50 m/s (h = 180 W/m2 K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10 °C. Comment on your calculation.
What is the physical significance of the Fourier number? Will the Fourier number for a specified heat transfer problem double when the time is doubled?