A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and a diameter of 0.38 inches the rest If it is subjected to a tensile load of 6,000 Ibs, what will be the total deformation of the bar if it has a modulus of elasticity E- 28.5 x 10 6 psi. O 01338 inches O 0.1378 inchies O 0.1423 inches 0.1352 inches O 0.1364 inches

A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and a diameter of 0.38 inches the rest If it is subjected to a tensile load of 6,000 Ibs, what will be the total deformation of the bar if it has a modulus of elasticity E- 28.5 x 10 6 psi. O 01338 inches O 0.1378 inchies O 0.1423 inches 0.1352 inches O 0.1364 inches

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2DP

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A steel bar 106mm long and having a square cross section 20 mm (0.8 in.) on an edge is pulled in tension with a load of 89,000 N, and experiencedan elongation of 0.10 mm. Assuming that the deformation is entirely elastic, calculate the elastic modulus of the steel?
A mild steel wire of radius 0.5 mm and length 3 m is stretched by a force of 49 N. Calculate for the longitudinal stress, longitudinal strain, and elongation produced in the body if Young’s modulus for steel is E = 2.1 x 1011 N/m2. Answers: (6.238 x 107 N/m2, 2.970 x 10-4 m/m, 0.891 mm)
A rectangular steel bar 0.5 inch thickness by 1.5 inches width and 220 ft long is subjectedto a 6000 lbs tensile load acting along its width. Find the deformation along its length andthickness if poison’s ratio is 0.27.
A steel column is 3 mm long and0.4 m in diameter. It carries a loadof 50 MN. Given that the modulusof elasticity is 200 GPa, calculatethe strain.
Which of the following nearly gives the frictional force at the 550lb block? a. 200 lb b. 420 lb c. 320 lb d. 140 lb
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.75 in2, 1.08 in2, and 0.56 in2 respectively.Determine the change in length (in inches) of the bar if P = 11599 lb.The moduli of elasticity are 30022 ksi for steel ,12071 ksifor bronze, and 10028 ksi for aluminum. Round off the final answer to four decimal places.
Calculate the total deformation of steelbars shown in Figure. (d1=15 mm, d2=25 mm and E=210 GPa) A= 5, B=3, C=8
Actual weight of steel bars = 1.520 kg/m, Standard weight of steel bars (16mm )= 1.579 kg/m, Load at yield point = 3480 kgf ,Load at breaking point = 7540 kgf, Maximum load = 7. 9260 kgf, Unit weight of steel = 7854 kg/m^3. What is the cross-sectional area in m^2? Compute it's yield strength,ultimate strength and breaking strength in MPA?
1. A force of 3000 lb stretches a steel rod into its proportional limit of 37 ksi. Calculate the approximate diameter of the steel rod.2. Considering a modulus of elasticity of 30 x 106 psi, calculate the deformation of the 3 ft. long steel rod in number 1.
The information in the photo attached shows elastic properties of a human tibula bone. If you were to take a small cuboidal cross section of the tibula bone and apply the ultimate shear stress, what would be the resulting strain? (a) 1.0 % (b) 6.7 % (c) 10 % (d) 15 % (e) None of the above.
Calculate the plane stresses involved where two pieces of steel are welded together. Our sign convention defines forces causing the object to be in tension positive and forces causing the object to be in compression negative. As we can see from the picture our σx = −4.5MPa and σy = 10MPa. Steel has an average Young’s modulus of elasticity of E = 200 GPa and an average Poisson’s ratio of ν = .285 Because it is not defined we will assume that initially there is no shear stress, τxy = 0. Solve only for: Compression in the x-direction(deformation along the weld)=(-Blank 4)? x 10^-5