A stock solution of analyte is made by dissolving 34.83 mg of copper (II) acetate hexahydrate (fw = 289.73 g/mol) in 25.00 mL of water. A second stock solution of internal standard is made by dissolving 28.43 mg of germanium (I) acetate (fw = 190.74 g/mol) into 25.00 mL of water. These solutions are used to make a series of standards for ﬂame atomic absorption analysis calibration. The standard solutions (each 10.00 mL total volume) should have the following concentrations of copper: 10.00; 25.00; 50.00; 100.0; and 200.0 μM. Each calibration solution should also contain 50.00 μM of germanium. What is the analyte stock solution concentration? What is the internal standard stock solution concentration? Complete this table.

A stock solution of analyte is made by dissolving 34.83 mg of copper (II) acetate hexahydrate (fw = 289.73 g/mol) in 25.00 mL of water. A second stock solution of internal standard is made by dissolving 28.43 mg of germanium (I) acetate (fw = 190.74 g/mol) into 25.00 mL of water. These solutions are used to make a series of standards for ﬂame atomic absorption analysis calibration. The standard solutions (each 10.00 mL total volume) should have the following concentrations of copper: 10.00; 25.00; 50.00; 100.0; and 200.0 μM. Each calibration solution should also contain 50.00 μM of germanium. What is the analyte stock solution concentration? What is the internal standard stock solution concentration? Complete this table.

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter14: Chromatography

Section: Chapter Questions

Problem 9P

See similar textbooks

Similar questions

Standardization of Sodium Thiosulfate Solution Primary Standard used: Potassium Dichromate Formula mass of 1o standard: __________________ % Purity of 1o standard: 99.80% Trials 1 2 3 Weight of K2Cr2O7 (g)Weight of K2Cr2O7 (g) 0.0315 0.0331 0.0380 Final Volume Reading Na2S2O3 (ml) 27.50 27.50 34.90 Initial Volume Reading Na2S2O3 (ml) 1.10 0.00 1.00 Net Volume Na2S2O3 used (ml) Molarity of Na2S2O3
50 mg of granular salt is briefly stirred into a glass container of 1/5 liter volume filled with water. After briefly mixing, some salt is still seen at the bottom of the class. The visible salt is filtered from the water, weighed and determined to have a mass of 20 mg. What is the dissolved phase concentration of salt remaining in the water? Provide your answer to the nearest whole number in units of mg/l.
Density of solution:Trial 1: 1.2 g/mLTrial 2: 1.2 g/mLTrial 3: 1.2 g/mL Average density = 1.2 g/mL What is the relative average deviaion, %?
A standard solution mixture containing each element at 500 ppm is provided. You will need to carefully dilute this so that your total volume is up to 50ml per standard solution mixture in the digitubes. Prepare calculations to show how you are going to prepare your calibration standards.
An HPLC method was developed for the separation and determination of ibuprofen in blood samples. A 3.00 mL blood sample dissolved in 70.00 mL solvent was prepared and 10.0 mL was injected into the HPLC. Standard ibuprofen solutions were also run.Calculate the ibuprofen present in the 3.00 mL blood sample The following data were obtained. Table po itoo: Ibuprofen concentration, mg/ml0.50 1.0 2.0 3.0 Blood sample Peak area (Right column)5.29.617.419.911.4
Table 1. Data for the Concentration of the KMnO4 Unknown Solution. Abs of Unknown Solution is 0.362 Absorbance Concentration Trial 1 0.120 0.00145 Trial 2 0.066 0.00104 Unknown Solution: __________ What is the Concentration of the Unknown Solution. _____________ Show statistical treatment of data.
The original solution was diluted by a factor of three, and then the absorbance of the diluted cereal sample solution was measured and recorded as (2.0x10^-1). Use the following trendline and dilution factor to determine the concentration of iron, in unit of M, in the original cereal sample solution. The trendline (linear regression) as displayed on the plot is y = 11898x - 0.0112.
SALT SOLUTION: Trial 1: Volume: 25 mLMass of 25mL solution: 29.824 gDensity: 1.2 g/mL Trial 2:Volume: 25 mLMass of 25 mL solution: 29.855 gDensity: 1.2 g/mL Trial 3:Volume: 25 mLMass of 25 mL solution: 29.816 gDensity: 1.2 g/mL METAL BAR: Method I - Trial 1:Mass of metal bar: 57.063 gVolume of metal bar: 6.7 cm^3Density of bar: 8.5 g/cm^3 Trial 2:Mass of metal bar: 57.063 gVolume of metal bar: 6.0 cm^3Density of bar: 9.5 g/cm^3 Trial 3:Mass of metal bar: 57.063 gVolume of metal bar: 6.0 cm^3Density of bar: 9.5 g/cm^3 Method 2 - Trial 1:Dimensions: diameter = 1.20 cm, height = 4.91 cmMass of metal bar: 57.063 gVolume of metal bar: 5.55 cm^3Density of bar: 10.3 g/cm^3 Trial 2:Dimensions: diameter = 1.20 cm, height = 4.95 cmMass of metal bar: 57.063 gVolume of metal bar: 5.60 cm^3Density of bar: 10.2 g/cm^3 Trial 3:Dimensions: diameter = 1.20 cm, height = 4.95 cmMass of metal bar: 57.063 gVolume of metal bar: 5.60 cm^3Density of bar: 10.2 g/cm^3 QUESTION - From your data, calculate the…
The gravimetric factor used to express CoCBr6·H20 in a sample that is finally weighed as PbClBr is choose below: FW PbClBr / 6 x FW CoCBr6·H20 FW CoCBr6·H20 / FW PbClBr FW CoCBr6·H20 / 6 x FW PbClBr 6 x FW PbClBr / FW CoCBr6·H20
FT-IR technique can be utilized for the analysis of unknown analytes by matching it with__________. Both choices are correct Commercial library/database Reference standard
Which statements are TRUE regarding internal standards? I. The response factor is calculated by using a mixture containing known amounts of analyte and internal standard and by using detector response to the analyte and the internal standard. II. Internal standards are useful where instrument response or quantity of sample analyzed varies over time. III. Detector response is inversely proportional to concentration. IV. Detector response to analyte and internal standard is assumed to be constant over a range of concentrations A. I, II, and III B. II, III, and IV C. I and II D. I, II, and IV
A 10-ml transfer pipet and a 200-ml volumetric flask (TC) are used to make 0.100 M and 0.0050 M solutions from a stock solution of 2.000(plus or minus) 0.005 M. Calculate the percent relative error for the three solutions if perfect technique is used. (See Garland Experiments in Physical Chemistry, 10th ed. p. 639-642) Report the two new molaritites