A storage tank has hot water. This water at a temperature of 85 °C is pumped to a 600 cm height at a rate of 6500 cm³/s. There are two different pipelines before and after the pump. Between the storage tank and pump, the pipeline is 6.6 m of 2-in. schedule 40 steel pipe. There are 3 elbow in this pipe. After the pump, the pipeline is 61 m of 2-in. pipe. There are 2 elbow in this pipe. Please calculate all frictional losses and make mechanical energy balance for calculating Ws of the pump in J/kg.

A storage tank has hot water. This water at a temperature of 85 °C is pumped to a 600 cm height at a rate of 6500 cm³/s. There are two different pipelines before and after the pump. Between the storage tank and pump, the pipeline is 6.6 m of 2-in. schedule 40 steel pipe. There are 3 elbow in this pipe. After the pump, the pipeline is 61 m of 2-in. pipe. There are 2 elbow in this pipe. Please calculate all frictional losses and make mechanical energy balance for calculating Ws of the pump in J/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. Oil of specific gravity 0.750 is pumped from a tank over a hill through a 24′′ pipe with the pressure at the top of the hill maintained at 25.5 psi. The summit is 250 ft above the surface of the oil in the tank, and oil is pumped at the rate of 22.0 cfs. If the lost head from tank to summit is 15.7 ft, what horsepower must the pump supply to the liquid? indicate free body diagram
C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the pipeline. The diameter at the smaller end is 245 mm and at the larger end is 467 mm. The length of the conical tube is 1.8 m and the flow rate of the oil is 128 liters/s. The pressure at the smaller end is equivalent to a head of 9.7 m of oil. Considering the following two cases: (1) Neglecting friction, (without head loss) determine (i) the velocity at the smaller end in m/s, (ii) the velocity at the larger end in m/s, and (iii) the pressure at the larger end of the tube. (2) If a head loss (with head loss) in the tube is hL= 0.0153(V1-V2)2, where V1 is the velocity at the smaller end and V2 is the velocity at the larger end, determine (iv) the head loss in m of oil and (v) the pressure at the larger end of the tube.
A pipe has an initial radius of r1, which then changes to a radius of r2. The velocity of the water in the initial part of the pipe is v1. The segment of the pipe with the smaller radius is also 0.5 m higher than the initial pipe segment. What is the pressure difference between the two parts of the pipe? let r1=10cm let r2=6cm let v1=5m/s b) What is the volume flow rate in the pipe?
Water at 60°F is pumped from a reservoir to the top of a mountain through a 6-in. Schedule 120 pipe at an average velocity of 12 ft/s. The pipe discharges into the atmosphere at a level 3,000 ft above the level in the reservoir. The pipeline itself is 4,500 ft long. If the overall efficiency of the pump and the motor driving it is 70 percent and the cost of electric energy to the motor is 4 cents per kilowatt hour, what is the hourly energy cost for pumping this water?
1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
A shower head in your apartment needs to have water come out with a speed of 9.6m/s. The shower head has 20 circular openings. Each opening has a radius of 1mm. The shower head is connected to a pipe with radius of 0.8cm. The bathroom pipe is 8m above the ground level. The pipe at the ground level has twice the radius of the pipe in the bathroom upstairs. a) What is the volume flow rate at the ground floor? b) What must be the gauge pressure between the ground floor and the bathroom pipe? c) What is the gauge pressure between the bathroom pipe and the shower head opening where the water exits the shower head?
Suppose that you are willing to determine the diameter of the water jet impinging to the sink from the kitchen tap.The tap is produced to supply three different flow rates of the low, medium, and high. For each flow rate level, waterthat comes from the tap fills the beaker with a volume of 30 mL in 10 s, 6 s, and 2 s, respectively. The outlet of the tapis 13 mm, and the distance between the tap outlet and the sink is 53 mm. Determine the diameters of the water jetimpinging on the sink at three given flow rates.
The task is to to transfer the fluid from the source towards the tank (TANK A) lying on an elevated platform as shown. The goal is to fill up that 16.49 m by 2.23 m by 6.36 m tank (TANK A) within 11.5 mins (from empty to full). Your budget is limited to 605,000 pesos. Head loss on pipe due to friction is 1.23 meters per 1 meter of pipe. Because it's Fluid Machinery and not Engineering Economics, it's ok for your design to exceed the budget BUT YOU HAVE TO JUSTIFY IT.
The task is to to transfer the fluid from the source towards the tank (TANK A) lying on an elevated platform as shown. The goal is to fill up that 16.49 m by 2.23 m by 6.36 m tank (TANK A) within 11.5 mins (from empty to full). Your budget is limited to 605,000 pesos. Head loss on pipe due to friction is 1.23 meters per 1 meter of pipe. Because it's Fluid Machinery and not Engineering Economics, it's ok for your design to exceed the budget BUT YOU HAVE TO JUSTIFY IT. The pictures I will post is the guide to answer Its okay if the answer is computerized
Correct this problem with step-bystep please: A pump moves water horizontally at a rate of 0.02 m^3 /s. Upstream of the pump, where the pipe diameter is 90 mm, the pressure is 120 kPa. Downstream of the pump, where the pipe diameter is 30 mm, the pressure is 400 kPa. If the loss in energy across the pump due to fluid friction effects is 170 N.m/kg. Determine the hydraulic efficiency of the pump.
Gasoline at 38°C is being drawn from a closed tank having a pressure of 70kPag. The level of gasoline in the tank is 2.5m above the pump centerline. The suction line friction loss is 0.6m. The vapor pressure of the gasoline is 48kPa absolute and its specific gravity is 0.72. Determine the NPSH available.
In oasis Water Company to purify the water, it is flowing through a reducer in a horizontal pipe where the diameter is reduced from 35 cm to 25 cm. The pressure in the 35 cm pipe just upstream of the reducer is 150 kPa. The fluid has a vapor pressure of 50 kPa and a specific weight of 5 kN/m3. Neglecting frictional effects, calculate flow rate of water through this pipe in lit/s. Draw diagram neatly