A storage tank with base area 40 m2 is being filled with water through a duct in which the volumetric flow rate is 12 L/s, as shown in Fig. 3. Water is concurrently being extracted from the storage tank through two exit pipes with cross-section area 150 cm2. The inlet of the exit pipes is located at a certain height, denoted h in Fig. 3, above the bottom of the storage tank. Water is assumed to be inviscid and incompressible. exit pipes Ve 12 L/s 150 cm? K150 cm 7 m storage tank (base area 40 m2) Figure 3

A storage tank with base area 40 m2 is being filled with water through a duct in which the volumetric flow rate is 12 L/s, as shown in Fig. 3. Water is concurrently being extracted from the storage tank through two exit pipes with cross-section area 150 cm2. The inlet of the exit pipes is located at a certain height, denoted h in Fig. 3, above the bottom of the storage tank. Water is assumed to be inviscid and incompressible. exit pipes Ve 12 L/s 150 cm? K150 cm 7 m storage tank (base area 40 m2) Figure 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to the atmosphere. The water level is 2.5 m above the outlet. The tank air pressure above the water level is 250 kPa (absolute) while the atmospheric pressure is 100 kPa. Neglecting frictional effects, determine the initial discharge rate of water from the tank.
A water tank is attached to a piping system with a sharp edge inlet (KL=0.5). Determine the velocity of the outlet water if the system has two elbow pipes (KL=1.5), the length of the entire system is 10m, the diameter is 1.5cm, the friction factor is 0.002 and the height between the water and the outlet are 5m.
Water with a temperature of 20 oC is pumped from a tank open to the atmosphere (zA = 2.62 m), through two cast iron (roughness value ε=0.005mm) pipes of 26.2 m length, connected in parallel with the higher one (zB = 9.62 m). Pipe diameters are D1 = 3.62 cm and D2 = 5.62 cm, respectively. The water is pumped with a motor-pump group, whose efficiency is 66.2% and consumes 7062 W of electrical power during operation. miner losses in pipes connecting parallel pipes to tanks are neglected. Find the total volume flow rate between the tanks and the volume flow rate in each of the parallel pipes. Solve the problem by making at least three iterations. Solve the problem by making the necessary assumptions and drawing the schematic figure. (a=6 and b=2 on the figure)
Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is 5 m long and has a 6-cm diameter, while the second pipe is 5 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged, and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head and the minimum pumping power to maintain the indicated flow rate. (The density and dynamic viscosity of water at 15°C are ρ = 999.1 kg/m3 and μ = 1.138x10-3 kg/m.s. The loss coefficient is KL = 0.5 for a sharp-edged entrance. The roughness of cast iron pipes is ε= 0.00026 m.)
Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 3-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged, and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head and the minimum pumping power to maintain the indicated flow rate.
A centrifugal pump is required to deliver 50 liters of water per second to a height or 30 m through a 100 m long pipe of 15 cm diameter. The inlet losses in the suction pipe are estimated to be 0.35 m. Assuming an overall efficiency of 70 percent and taking Darcy’s friction coefficient of 0.015 for the pipeline, determine the power, in kW, required to drive the pump.
Water at 15°C is drained from a large reservoir using two horizontal plastic pipes connected in series. The first pipe is 20 m long and has a 10-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 18 m above the centerline of the pipe. The pipe entrance is sharp-edged, and the contraction between the two pipes is sudden. Neglecting the effect of the kinetic energy correction factor, determine the discharge rate of water from the reservoir.
Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet is ( WITH FREE BODY DIAGRAM) CHOICES: A.7.12 B.6.21 C.8.7 D.5.05
You have a 550 W pump with 70% efficiency available. Is it possible to use this pump to carry 10 m3/h of a liquid through a 4.7 cm inside diameter pipe, from one open tank to another, if the liquid is discharged at a point 10 m above the level of liquid in the suction tank and the total friction losses are 50 J/kg? The density and viscosity of the liquid are 1050 kg/m3 and 2 cp respectively.
A 70% efficient water pump is use to pump water to a tank which is 30 m above, the water pump is operated at 240-V, 10-A. The pipe has 5-cm-diameter at inlet and 4-cm-diameter at outlet. Irreversible head loss of the piping system is 3 m. Determine the volume flow rate and mass flow rate of the water.
Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is X= 5 m long and has a 6-cm diameter, while the second pipe is 5 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged, and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head and the minimum pumping power to maintain the indicated flow rate. (The density and dynamic viscosity of water at 15°C are ρ = 999.1 kg/m3 and μ = 1.138x10-3 kg/m.s. The loss coefficient is KL = 0.5 for a sharp-edged entrance. The roughness of cast iron pipes is ε= 0.00026 m.)
Air enters a fan through a duct velocity of 6.3 m/s and an inlet static pressure of 2.5cm of water less than the atmospheric pressure. The air leaves the fan through the duct at a velocity of 11.25 m/s and a discharge pressure of 7.62cm of water above the atmospheric pressure. If, the density of the air is 1.2kg/m3and the fan delivers 9.45m3/s, what is the fan efficiency when the power input to the fan is 13.75 kW at the coupling. Show schematic diagram and provide solutions.