A structure consists of two thin rectangular plates having the same dimensions (shown in figure) and same mass, m = 8 kg each. The two plates are welded together to form a rigid body that may rotate in the plane. Determine, for this rigid body, the moment of inertia Ip about the fixed point P. wS P is fixed

A structure consists of two thin rectangular plates having the same dimensions (shown in figure) and same mass, m = 8 kg each. The two plates are welded together to form a rigid body that may rotate in the plane. Determine, for this rigid body, the moment of inertia Ip about the fixed point P. wS P is fixed

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by ka = 3,000 N-m/rad and ka = 4.000 N-m/rad. The turbine generates a harmonic torque given by M(t) = M, cos at about the shaft axis with M, = 200 N-m and e = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is Jo = 0.05 kg-m. Assuming the equivalent torsional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, )
A disk attached with a shaft AB, which both end of the shaft have base support, as shown in figure 1 below. Determine the moment of inertia of the disk about the axis of shaft AB.The disk has a mass of 20kg
A thin uniform rod of mass M and length L is bent at its center so that the two segments are now perpendicular to each other. Find its moment of inertia about an axis perpendicular to its plane and passing through (a) the point where the two segments meet and (b) the midpoint of the line connecting its two ends.
A caravan weighs 28 kN. It has a wheel base of 2 m, track width 1m and height ofC.G. 300 mm above the ground level and lies midway between the front andrear axle. The engine flywheel rotates at 2950 rpm clockwise when viewed from thefront. The moment of inertia of the flywheel is 4 kg-m 2 and moment of inertia ofeach wheel is 3 kg-m 2 . Find the reactions between the wheels and the ground whenthe car takes a curve of 15 m radius towards right at 30 km/h, taking intoconsideration the gyroscopic and the centrifugal effects. Each wheel radius is 400 mm.
find the moment of inertia of a quarter of a hollow disk (shaded part of the figure), of inner radius a and outer radius b, of mass M and surface mass density that grows linearly as one moves away from the center of a disk. The axis about which to measure the moment of inertia passes perpendicularly through the center of the hollow disk.
A homogeneous circular disc with radius R = 5.04 m and thickness t = 10.1 x 10^−3 m rotates around the z-axis (perpendicular to the disc, see figure). A rectangular hole is cut from the centre of the disc with the base b = 4.725 m and the height h = 4.719 m. Calculate the mass moment of inertia of the disc around the z-axis if its density is 6.38 kg/m³.
Consider a hollow drainage concrete cylinder of uniform mass density of 2,400kg/m^3 with length L=60m with R1 of 2.8m. Find its outer radius (R2) in m if the moment of inertia is 5, 067, 000kgm^-2 about its axis to symmetry is.
The machine element shown in the figure is made of steel (Density: 7850 kg / m ^ 3). Determine the mass moments of inertia of the machine element, with respect to a system of axes parallel to the X, Y and Z axes, located at the center of gravity of the element.
In the figure the L- shaped machine part is composed of two homogeneous bars . Bar 1 is tungsten alloy with mass density 14,000 kg/m3 , and bar 2 is steel with mass density 7800 kg/m3 . Determine its moment of inertia about the x axis.
The mass moment if inertia of a cylinder about its central axis perpendicular to a circular cross section is
Consider a rectangular frame made of 4 thin rods (slender rod) as shown in the figure. Consider 4 axes ZP, ZQ, ZR, ZS perpendicular to the screen that pass through the points P, Q, R, S as shown in the figure.Around which of the four axes will the mass moment of inertia be the smallest? a. ZP b. ZQ c. ZR d. ZS
Calculate the mass moment of inertia for a rectangular plate for the H-H axis shown in the link. The mass of the plate is 8 kg, a = 5 m and b = 1 m.