A student has collected data from a simple circuit, built with a 10 2 resistor, a 202 resistor, and a 30 2 resistor, in order to identify the type of circuit. The student concludes that it was a series circuit. What evidence would best support the students' claim? • A. d. The student noticed that as resistors are added, the total amount of voltage in the circuit increased. о в. Ь. The student can measure the current for each resistor. A series circuit would have the same current for each resistor. O C. a. The student can measure the voltage for each resistor, A series circuit would have the same voltage for each resistor. O D. C. The student noticed that as resistors are added, the total amount of current in the circuit increased.

A student has collected data from a simple circuit, built with a 10 2 resistor, a 202 resistor, and a 30 2 resistor, in order to identify the type of circuit. The student concludes that it was a series circuit. What evidence would best support the students' claim? • A. d. The student noticed that as resistors are added, the total amount of voltage in the circuit increased. о в. Ь. The student can measure the current for each resistor. A series circuit would have the same current for each resistor. O C. a. The student can measure the voltage for each resistor, A series circuit would have the same voltage for each resistor. O D. C. The student noticed that as resistors are added, the total amount of current in the circuit increased.

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter21: Circuits And Dc Instruments

Section: Chapter Questions

Problem 53PE: A 1,00-?O voltmeter is placed in parallel with a 75.0kresistor in a circuit, (a) Draw a circuit...

See similar textbooks

Similar questions

Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
A person with body resistance between his hands of 10.0k accidentally grasps the terminals of a20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation, (b) If the internal resistance of the power supply is 2000 , what is thecurrent through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low- resistance devices? Explain your reasoning.
The emf devices in the circuits shown in Figure P29.28 are identical. a. Redraw circuit 1 in figure P29.28, including (and labeling) the current in each branch of the circuit. Apply the junction rule to write an equation in terms of the currents you have labeled. b. Repeat part (a) for circuit 2 in Figure P29.28. c. Simplify your equations if necessary, and compare your answers for each circuit. What can you say about the two circuits?
An automobile starter motor has an equivalent resistance of 0.0500 and is supplied by a 12.0-V battery with a 0.0100- internal resistance, (a) What is thecurrent to the motor? (b) What voltage is applied to it? (c) What power is supplied to the motor? (d) Repeat these calculations for when the battery connections are corroded and add 0.0900 to the circuit. (Significant problems are caused by even small amounts of unwanted resistance in low-voltage, high-current applications.)
In the circuit of Figure P28.30, determine (a) the current in each resistor and (b) the potential difference across the 200- resistor.
Consider a circuit that consists of a real battery with an emf and an internal resistance of r connected to a variable resistor R. (a) In order for the terminal voltage of the battery to be equal to the emf of the battery, what should the resistance of the variable resistor be adjusted to? (b) In older to get the maximum current from the battery, what should the resistance variable resistor be adjusted to? (c) In order for the maximum power output of the battery to be reached, what should the resistance of the variable resistor be set to?
A 500- resistor, an uncharged 1.50-F capacitor and a 6.16-V emf are connected in series, (a) What is the initial current? (b) What is the RC time constant? (c) What is the current after one time constant? (d) What is the voltage on the capacitor after one time constant?
A person with body resistance between his hands of 1.00 k accidentally grasps the terminals of a 20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation. (b) If the internal resistance of the power supply is 2000 , what is the current through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low-re si stance devices? Explain your reasoning,
Consider a series RC circuit as in Figure P18.35 for which R = 1.00 M, C = 5.00 F, and = 30.0 V. Find (a) the time constant of the circuit and (b) the maximum charge on the capacitor after the switch is thrown closed. (c) Find the current in the resistor 10.0 s after the switch is closed. Figure P18.35 Problem 35 and 38.
Consider the circuit shown in Figure P28.9. Find (a) the current in the 20.0- resistor and (b) the potential difference between points a and b.
A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.6 V when it is delivering 20.0 W of power to an external load resistor R. (a) What is the value of R? (b) What is the internal resistance of the battery?
A student makes a homemade resistor from a graphite pencil 5.00 cm long, where the graphite is 0.05 mm indiameter. The resistivity of the graphite is =1.38102/m . The homemade resistor is place inseries with a switch, a 10.00-mF capacitor and a 0.50-V power source, (a) What is the BC time constant of the circuit? (b) What is the potential drop across the pencil 1.00 s after the switch is closed?