A student is provided with an unknown solution, which will contain one of the follow anions: chloride (CT), phosphate (PO,), or sulfate (SO,). The unknown solution is mixed with barium nitrate, iron(III) nitrate, and silver nitrate. The student's observations are shown below. Ba(NO3)2 (aq) Fe((NO3)3 (aq) AGNO3 (aq) Unknown solution precipitate precipitate precipitate Which anion does the unknown solution contain? Chloride, CI Phosphate, PO, Sulfate, So,-

A student is provided with an unknown solution, which will contain one of the follow anions: chloride (CT), phosphate (PO,), or sulfate (SO,). The unknown solution is mixed with barium nitrate, iron(III) nitrate, and silver nitrate. The student's observations are shown below. Ba(NO3)2 (aq) Fe((NO3)3 (aq) AGNO3 (aq) Unknown solution precipitate precipitate precipitate Which anion does the unknown solution contain? Chloride, CI Phosphate, PO, Sulfate, So,-

Introductory Chemistry: A Foundation

9th Edition

ISBN:9781337399425

Author:Steven S. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Donald J. DeCoste

Chapter15: Solutions

Section: Chapter Questions

Problem 41CR

See similar textbooks

Similar questions

Addition of water to concentrated sulfuric acid is dangerous because it generates enough heat to boil the water, causing it to spatter out of the container. For this reason, chemists remember to add acid to water. In a dilution experiment, we calculate the amount of the more concentrated solution that must be measured out. If we place this concentrated solution (Figure 4.7) in the volumetric flask first, then dilute with water, we violate the caution Add acid to water. Describe a safer variation on the method shown in Figure 4.7 that allows the quantitative dilution of concentrated sulfuric acid. Figure 4.7 Preparing a dilute solution from a concentrated solution. (a) Draw the concentrated solution into a pipet to a level just above the calibration mark. (b) Allow the liquid to settle down to the calibration line. Touch the tip of the pipet to the side of the container to remove any extra liquid. (c) Transfer this solution to a volumetric flask. Again touch the pipet to the wall of the flask to ensure complete transfer, but do not blow out the pipet because it is calibrated for a small amount of liquid to remain in the tip. (d) Dilute to the mark with solvent. Frequently, especially with concentrated acids, it is best to have some solvent present in the volumetric flask before you add the concentrated sample.
Label each of the following statements as true or false. Explain your answers, and provide an example for each that supports your answer. l type='a'> All nonelectrolytes are insoluble. i>All insoluble substances are nonelectrolytes. i>All strong electrolytes arc soluble. i>All soluble substances are strong electrolytes.
What is a dilution? What stays constant in a dilution? Explain why the equation M1 V1 = M2 V2 works for dilution problems.
4. A 10.00-mL sample of a vinegar solution is titrated with a 0.178N NaOH solution. It requires 48.12 mL of the base solution to turn the solution in flask light pink. What is the amount of equivalent of base in the 48.12-mL portion? What is the amount of equivalent of the acid in the vinegar sample? What is the normality of the vinegar solution?
1.The following reaction takes place as represented by the balanced chemical equation below: Mg(NO3)2 (aq) + 2 NaOH (aq) --> Mg(OH)2 (s) + 2 NaNO3 (aq) How many mL of a 0.55 M solution of Mg(NO3)2 would be required to fully react 145 mL of 1.2 M solution of NaOH? Numerical answer: Unit:
For the following reaction:H2CO3 + 2 NaOHNa2CO3 + 2 H2O(1) What is the equivalent mass of H2CO3? g/equiv(2) Calculate the number of equivalents in 27.1 grams of H2CO3. equiv