6404801600.0020,0040.0060.0080.010Strain (mm/mm)A tensile test specimen of Aluminum alloy having a gauge length of 280 mm wastested to fracture. Stress and strain data obtained during the test are shown in theattached Figure. **Answers are approximate - do your best to read the graph.Determine:(a) the modulus of elasticity in GPa (4sigs). Enter this value into D2L answer box.(b) the proportional limit in MPa (3sigs).(c) the ultimate strength in MPa (3sigs).(d) Ductility of material based on percent elongation. (3sigs)Your Answer:Stress (MPa)

Answered: Image /qna-images/answer/c12e153a-e398-4ecc-bfba-afa7a8643326.jpg

A tensile test specimen of Aluminum alloy having a gauge length of 280 mm was tested to fracture. Stress and strain data obtained during the test are shown in the attached Figure. **Answers are approximate - do your best to read the graph.

A tensile test specimen of Aluminum alloy having a gauge length of 280 mm was tested to fracture. Stress and strain data obtained during the test are shown in the attached Figure. **Answers are approximate - do your best to read the graph.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tensile test was carried out on a tensile sample with a gauge length of 62.35 mm and a cross-sectional area of 5.17mm. Determine the final fracture length and final cross-sectional area of the specimen if the percentage elongation was 17.64% and the percentage reduction in the area was 3.78%
You are called as an expert witness to analyze the fracture of a sintered silicon carbide plate that was fractured in bending when a blunt load was applied to the plate center. Measurement of the distance between the fracture origin and the mirror/mist boundary on the fracture surface gives a radius of 0.796 mm. You are given three pieces of the same SiC to test, and you determine that the mirror radius is 0.603, 0.203, and 0.162 mm for bending failure stress levels of 225, 368, and 442 MPa, respectively. What is your estimate of the stress present at the time of fracture for the original plate?
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 150 kN. - Length of the specimen is 24 mm. - The yield strength is 78 kN/mm2. - The percentage of elongation is 42 %. Determine the following iii) Stress under an elastic load of 14 kN, iv) Young's Modulus if the elongation is 1.7 mm at 14 kN and (v) Final diameter if the percentage of reduction in area is 26 %. I wont answer for this three questions only: 1)Final Area of the Specimen at Fracture (in mm) 2)Final Diameter of the Specimen after Fracture (in mm) 3)Initial Cross-sectional Area (in mm2)
The following engineering tensile properties are given for the 1080 steel:-Yield strength (MPa): 585-Tensile strength (MPa): 965-Elongation to fracture for specimen of 5cm gage length (%): 12A 5cm long circular rod of 1080 steel specimen with a diameter of 1.28cm isloaded to failure in tension. a) What was the maximum load needed to break the specimen?(20 points)b) If necking initiated at 80% of the total elongation, prior to this point thespecimen deformation is uniform, compute the true stress at the point ofnecking initiation.
39) A tensile test specimen has a gauge length=2in. and a diameter of 0.875in. Yielding occurs at a load of 35,500lbs. The corresponding gauge length = 2.0113in. (neglect the .2% yield point). The maximum load of 45,000lbs is reached at a gauge length of 2.543in. If fracture occurs at a gauge length of 2.673in, determine the percent elongation at fracture (Round to the nearest whole %)
A brass specimen of the circular cross-section is fractured at 151 kN force and the final length of the specimen at fracture is 49 mm. The fracture strength of the specimen is found to be 74 kN/mm2. The percentage of elongation of the specimen is 42 %. Determine the following (i) Diameter of the specimen ii) Initial length of the specimen iii) Stress under an elastic load of 16 kN iv) Young's Modulus if the elongation is 1.6 mm at 16 kN (v) Final diameter if the percentage of reduction in area is 20 % solve: Stress under the elastic load (in N/mm2) = Young's Modulus of the Specimen (in N/mm2) = Final Area of the Specimen at Fracture (in mm) =
A brass specimen of the circular cross-section is fractured at 151 kN force and the final length of the specimen at fracture is 49 mm. The fracture strength of the specimen is found to be 74 kN/mm2. The percentage of elongation of the specimen is 42 %. Determine the following (i) Diameter of the specimen ii) Initial length of the specimen iii) Stress under an elastic load of 16 kN iv) Young's Modulus if the elongation is 1.6 mm at 16 kN (v) Final diameter if the percentage of reduction in area is 20 % solve: Final Diameter of the Specimen after Fracture (in mm) =
The following data was obtained as a result of tensile testing of a standard 0.505 inch diameter test specimen of magnesium. After fracture, the gage length is 2.245 inch and the diameter is 0.466 inch. a). Calculate the engineering stress and strain values to fill in the blank boxes and plot the data. Load(lb) Gage Length (in) Stress (kpsi) Strain 0 2 1000 2.00154 2000 2.00308 3000 2.00462 4000 2.00615 5000 2.00769 5500 2.014 6000 2.05 6200 (max) 2.13 6000 (fracture) 2.255 b). Calculate the modulus of elasticity c). If another identical sample of the same material is pulled only to 6000 pounds and is unloaded from there, determine the gage length of the sample after unloading.
Request: Can you please help me with answering the following question? Thank you. Question: A specimen of a ceramic material having an elastic modulus of 250 GPa (36.3 x 106 psi) is pulled in tension with a stress of 750 MPa (109,000 psi). Will the specimen fail if its “most severe flaw” is an internal crack that has a length of 0.20 mm (7.87 x 10-3 in.) and a tip radius of curvature of 0.001 mm (3.94 x 10-5 in.)? Why or why not?
For a steel element with a 0.2% steel characteristic, a stress test was applied and the analysis of the data thrown by the material is required in terms of a variation of force and the respective deformations. Determine the following: A.Determine the percentage elongation at the point where the part develops the fracture. B.Construct the “Stress-Strain” diagram C.Maximum tensile strength of the part.
The following data were obtained during a tensile test of an alluminium alloy specimen. Initial diameter = 18mm Original gauge length = 45mm Final gauge length = 53mm Load at elastic limit = 82kN Yield load = 93kN Maximum load = 168kN Determine the Yield stress - answer to be provided in MPa correct to 3 decimal
The following data were obtained from the tensile test of Aluminum alloy. The initial diameter of testspecimen was 0.505 inch and gauge length was 2.0 inch. Plot the stress strain diagram and determine(a) Proportional Limit (b) Modulus of Elasticity (c) Yield Stress at 0.2% offset (d) Ultimate Stress and(e) Nominal Rupture Stress.