a) The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an innerdiameter of 20 mm and outer diameter of 28 mm. The rod has a diameter of 12mm. Determine the average normal stress at points D and E and represent thestress on a volume element located at each of these points. Ans: o,=13.3 MPa,%3DОE%3D70.7 MPа.6 kN4 kN8 kN6 kN E

Given data outer diameter of pipe (do) = 28 mm inner diameter of pipe (di) = 20 mm diameter of rod…

Answered: a) The built-up shaft consists of a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pressurized spherical tank is to be made of 12-mm-thick steel. If it is subjected to an internal pressure of p = 1.4 MPa, determine its outer radius if the maximum normal stress is not to exceed 105 MPa.
A cylindrical propane tank has an outside diameter of 3.25 m. If the allowable hoop stress is 100 MPa and the allowable axial or longitudinal stress is 45 MPa, determine the minimum thickness of the pipe when the internal pressure that can be applied to the tank is 1.25 MPa.
A spherical gas tank has an inner radius of (?? ) = 1.5 ?. If it is subjected to an internal pressure p = 300 kPa, determine its required thickness if the maximum normal stress is not to exceed 12 MPa. Also determine the outer radius. Don't use chat gpt.
The steel bracket below is used to connect the ends of two cables. If the applied force P=1.50kip, determine the maximum normal stress (in ksi) in the bracket. Assume the bracket is made from a rod having a diameter 1.5in.
433 The steel pipe is filled with concrete and subjected 10 a compressive force of 80 kN. Determine the averaee normal stress in the concrete and the steel due to this loading. The pipe has an outer diameter of 80 mm and oo inner diameter of 70 mm. E, = 200 GPa, E. = 24 GPa.
A steel pipe with an outer diameter of 50 mm and a wall thickness of 5 mm is subjected to aninternal pressure of 10 MPa and an axial load of 20 kN at an angle of 45 degrees to the axis of thepipe. Determine the maximum axial stress and maximum hoop stress developed in the pipe.
The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is subjected to an internal pressure of 500 psi and the axial tension and torsional loadings shown, determine the principal stress at a point on the surface of the pipe.
A thin-walled pressure vessel is made of steel with a thickness of 2 mm and an internal diameterof 300 mm. It is subjected to an internal pressure of 10 MPa. Determine the hoop stress andlongitudinal stress developed in the vessel.
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 556 mm2 and P= 36.79 kN. Round off the final answer to four decimal places.
Air pressure in the cylinder is increased by exerting forces P = 2 kN on the two pistons, each having a radius of 45 mm. If the cylinder has a wall thickness of 2 mm, determine the state of stress in the wall of the cylinder.
The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C and subjected to the horizontal 20-lb force acting on the handle of the pipe wrench, determine the principal stresses in the pipe at point B, which is located on the surface of the pipe.
If P is equal to 125 kN Determine the normal stresses of members DH & HG in kPa. The diameter of each member is 120 mm.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS